2008 YAMAHA WR 250X stop start

5-1
2
3
4
56
7
8
9

OPERATION AND IMPORTANT RIDING POINTS
EAU15950
WARNING

EWA10270

Become thoroughly familiar
with all operating controls and
their functions before riding.
Consult a Yamaha dealer re-
garding any control or function
that you do not thoroughly un-
derstand.

Never start the engine or oper-
ate it in a closed area for any
length of time. Exhaust fumes
are poisonous, and inhaling
them can cause loss of con-
sciousness and death within a
short time. Always make sure
that there is adequate ventila-
tion.

Before starting out, make sure
that the sidestand is up. If the
sidestand is not raised com-
pletely, it could contact the
ground and distract the opera-
tor, resulting in a possible loss
of control.
EAU45310
NOTE:

This model is equipped with a lean an-
gle sensor to stop the engine in case of
a turnover. To start the engine after a
turnover, be sure to turn the main
switch to “OFF” and then to “ON”. Fail-
ing to do so will prevent the engine from
starting even though the engine will
crank when pushing the start switch.
EAU45120
Starting the engine
In order for the ignition circuit cut-off
system to enable starting, one of the
following conditions must be met:

The transmission is in the neutral
position.

The transmission is in gear with
the clutch lever pulled and the sid-
estand up.
WARNING

EWA10290

Before starting the engine,
check the function of the igni-
tion circuit cut-off system ac-
cording to the procedure
described on page 3-18.

Never ride with the sidestand
down.
1. Turn the key to “ON” and make
sure that the engine stop switch is
set to “ ”.
CAUTION:

ECA16130
The following warning lights should
come on for a few seconds, then go
off.

Fuel level warning light

PERIODIC MAINTENANCE AND MINOR REPAIR
6-42
1
2
3
4
5
6
7
8
9Engine overheating
WARNING

EWA10400

Do not remove the radiator cap when the engine and radiator are hot. Scalding hot fluid and steam may be
blown out under pressure, which could cause serious injury. Be sure to wait until the engine has cooled.

After removing the radiator cap retaining bolt, place a thick rag, like a towel, over the radiator cap, and then
slowly rotate the cap counterclockwise to the detent to allow any residual pressure to escape. When the hissing
sound has stopped, press down on the cap while turning it counterclockwise, and then remove the cap.
NOTE:

If coolant is not available, tap water can be temporarily used instead, provided that it is changed to the recommended coolant
as soon as possible.
Wait until the
engine has cooled.
Check the coolant level in the
reservoir and radiator.
The coolant level
is OK.The coolant level is low.
Check the cooling system
for leakage.
Have a Yamaha dealer checkand repair the cooling system.Add coolant. (See NOTE.)
Start the engine. If the engine overheats again,
have a
Yamaha dealer check
and repair the cooling system.
There is
leakage.
There is
no leakage.

INDEX
A
Air filter element and check hose,
cleaning ................................................ 6-15
Auxiliary light bulb, replacing .................. 6-36
B
Battery..................................................... 6-31
Brake and clutch levers, checking and
lubricating ............................................. 6-28
Brake and shift pedals, checking and
lubricating ............................................. 6-27
Brake fluid, changing .............................. 6-24
Brake fluid level, checking ...................... 6-23
Brake lever .............................................. 3-10
Brake lever free play, adjusting............... 6-22
Brake pedal ............................................. 3-10
C
Cables, checking and lubricating ............ 6-27
Care .......................................................... 7-1
Catalytic converter .................................. 3-12
Clutch lever ............................................... 3-9
Clutch lever free play, adjusting .............. 6-21
Coolant.................................................... 6-12
Coolant temperature warning light ............ 3-2
D
Dimmer switch .......................................... 3-9
Drive chain, cleaning and lubricating ...... 6-26
Drive chain slack ..................................... 6-25
E
Engine break-in ......................................... 5-3
Engine idling speed................................. 6-17
Engine oil and oil filter element ................. 6-9
Engine stop switch .................................... 3-9
Engine trouble warning light...................... 3-3
EXUP system .......................................... 3-17
F
Front and rear brake pads, checking .......6-23
Front fork, adjusting .................................3-13
Front fork, bleeding ..................................3-15
Front fork, checking .................................6-29
Fuel ..........................................................3-11
Fuel consumption, tips for reducing ...........5-3
Fuel level warning light ..............................3-2
Fuel tank cap ...........................................3-11
Fuses, replacing ......................................6-32
H
Handlebar switches ...................................3-8
Headlight bulb, replacing .........................6-33
Helmet holder ..........................................3-13
High beam indicator light ...........................3-2
Horn switch ................................................3-9
I
Identification numbers................................9-1
Ignition circuit cut-off system ...................3-18
Indicator and warning lights .......................3-2
K
Key identification number ..........................9-1
L
License plate light bulb, replacing ...........6-36
M
Main switch/steering lock ...........................3-1
Matte color, caution ...................................7-1
Model label ................................................9-2
Multi-function display .................................3-3
N
Neutral indicator light .................................3-2
P
Panels, removing and installing .................6-6Parking ...................................................... 5-4
Part locations............................................. 2-1
Periodic maintenance and lubrication
chart ........................................................ 6-2
Pre-operation check list ............................. 4-2
R
Rear brake light switch, adjusting............ 6-22
Rear suspension, lubricating ................... 6-29
S
Safety information ..................................... 1-1
Seat ......................................................... 3-12
Shifting ...................................................... 5-2
Shift pedal ............................................... 3-10
Shock absorber assembly, adjusting....... 3-15
Sidestand ................................................ 3-18
Sidestand, checking and lubricating ........ 6-29
Spark plug, checking ................................. 6-8
Specifications ............................................ 8-1
Starting the engine .................................... 5-1
Start switch ................................................ 3-9
Steering, checking ................................... 6-30
Storage ...................................................... 7-3
Supporting the motorcycle....................... 6-37
T
Tail/brake light ......................................... 6-35
Throttle cable free play, checking............ 6-18
Throttle grip and cable, checking and
lubricating .............................................. 6-27
Tires ........................................................ 6-18
Tool kit ....................................................... 6-1
Troubleshooting....................................... 6-40
Troubleshooting charts ............................ 6-41
Turn signal indicator light .......................... 3-2
Turn signal light bulb, replacing............... 6-35