2008 YAMAHA VX SPORT engine overheat

Operation
62
(6) Drain residual water from the exhaust
system by alternately squeezing and re-
leasing the throttle lever for 10 to 15 sec-
onds while the engine is running.
CAUTION:
ECJ00561
Do not run the engine for more than 15
seconds without supplying water, other-
wise the engine could overheat.
(7) If the watercraft will be stored for a week
or more, lubricate internal engine compo-
nents to help prevent corrosion. (See
page 64 for lubrication procedures.)
(8) Rinse the engine and engine compart-
ment with a small amount of water.
CAUTION:
ECJ00570
Do not use high-pressure water when rins-
ing the engine or engine compartment as
severe engine damage could result.
(9) Wipe the engine and engine compart-
ment dry with a clean cloth (repeat step 3,
if necessary).
(10) Wipe the hull, handlebars, and jet unit dry
with a clean cloth.
(11) Spray a rust inhibitor on metallic parts to
minimize corrosion.
(12) Allow the engine compartment to air dry
completely before installing the seat.
EJU33451
Transporting
When transporting the watercraft on a trailer,
secure the tie downs to the trailer through the
bow eye and stern eyes.
CAUTION:
ECJ00621

Do not attach ropes or tie downs to any
part of the watercraft other than the bow
eye and stern eyes to secure the water-
craft to the trailer. Otherwise, the water-
craft may be damaged.

Do not route ropes or tie downs over the
seat, as they may leave permanent
marks on the seat’s surface. Also, wrap
the ropes or tie downs with towels or
rags where they touch the body of the
watercraft to avoid scratches or dam-
age.

For VX Deluxe/VX Cruiser:
Before putting the watercraft on the trail-
er or transporting it, be sure to put the
shift lever in the forward position, other-
wise the reverse gate may hit an obsta-
cle, which may cause damage.
UF1K73E0.book Page 62 Wednesday, July 11, 2007 9:15 AM

Maintenance and care
63
EJU33490
Storage
WARNING
EWJ00330
Always place the watercraft upright in a
horizontal position when storing it, other-
wise fuel could leak out into the engine or
engine compartment, which could create a
fire hazard.
Storage for long periods of time, such as win-
ter storage, requires preventive maintenance
to ensure against deterioration. It is advisable
to have the watercraft serviced by a Yamaha
dealer prior to storage. However, the following
procedures can be performed by the owner.
EJU33542Flushing the cooling system
Flushing the cooling system is essential to
prevent it from clogging with salt, sand, or dirt.
CAUTION:
ECJ00121

Do not supply water to the cooling water
passages when the engine is not run-
ning. The water could flow back through
the muffler into the crankcase, causing
severe engine damage.

Do not run the engine for more than 15
seconds without supplying water or
over 4000 r/min on land, otherwise the
engine could overheat.
(1) Place the watercraft in a horizontal posi-
tion.
(2) Remove the seat. (See page 23 for seat
removal and installation procedures.)
(3) Remove the flushing hose connector
cap, and then insert the garden hoseadapter into the flushing hose connector
and turn it until it is securely connected.
(4) Connect the garden hose adapter to a
water tap using a garden hose.
NOTE:
A garden hose is not included and must be
purchased separately.
(5) Start the engine, and then immediately
turn the water supply on until water flows
out continually from the jet thrust nozzle.
(6) Run the engine at idling speed for about
3 minutes watching the engine condition.
If the engine stops while flushing, turn the
water supply off immediately and repeat
the above steps.
(7) Turn the water supply off, and then force
the remaining water out of the cooling
1Flushing hose connector cap
2Garden hose adapter
3Flushing hose connector
UF1K73E0.book Page 63 Wednesday, July 11, 2007 9:15 AM

Maintenance and care
64
water passages by alternately squeezing
and releasing the throttle lever for 10 to
15 seconds.
(8) Stop the engine.
(9) Remove the garden hose adapter and in-
stall the flushing hose connector cap.
EJU33622Lubrication
WARNING
EWJ00260
Do not spray flammable rust inhibitor
products on engine surfaces while the en-
gine is hot. The sprayed substance or pro-
pellants could catch fire.
(1) Remove the seat. (See page 23 for seat
removal and installation procedures.)
(2) Loosen the clamp screw and disconnect
the air intake duct.(3) Spray a rust inhibitor into the intake open-
ing for 3 seconds.
(4) Connect the air intake duct and tighten
the clamp screw.
(5) Start the engine in a well-ventilated area
and let it run at idle for 15 seconds.
CAUTION:
ECJ00561
Do not run the engine for more than 15
seconds without supplying water, other-
wise the engine could overheat.
(6) Lubricate all cables such as the throttle
and steering cables.
NOTE:
Use a suitable marine grease applicator to
pressure-lubricate the cables and purge out
any moisture between the inner and outer ca-
bles.
(7) Lubricate the areas of the watercraft
specified in “Lubrication points” on page
73.
EJU33670Fuel system
WARNING
EWJ00280
GASOLINE AND ITS VAPORS ARE HIGH-
LY FLAMMABLE AND EXPLOSIVE!
1Clamp screw
2Air intake duct
1Intake opening
UF1K73E0.book Page 64 Wednesday, July 11, 2007 9:15 AM

Trouble recovery
80
EJU34620
Emergency procedures EJU34630Cleaning the jet intake and impeller
If weeds or debris get caught in the jet intake
or impeller, cavitation can occur, causing jet
thrust to decrease even though engine speed
rises. If this condition is allowed to continue,
the engine will overheat and may seize. If
there is any sign that the jet intake or impeller
is clogged with weeds or debris, return to
shore and check the intake and impeller. Al-
ways stop the engine before beaching the wa-
tercraft.
WARNING
EWJ00780
Before attempting to remove weeds or de-
bris from the jet intake or impeller area,
shut the engine off and remove the clip
from the engine shut-off switch. Severe in-
jury or death could result from coming incontact with the rotating parts of the jet
pump.
CAUTION:
ECJ00650
If weeds or debris get caught in the jet in-
take, do not operate the watercraft above
trolling speed until they have been re-
moved.
(1) Turn the watercraft on its side as shown.
UF1K73E0.book Page 80 Wednesday, July 11, 2007 9:15 AM

Index
A
Air filter element ....................................... 71
B
Battery ................................................ 44, 65
Battery, checking...................................... 74
Battery, jumping ....................................... 81
Beaching the watercraft ........................... 60
Bilge ......................................................... 43
Boarding alone ......................................... 55
Boarding and starting from a dock ........... 54
Boarding and starting in deep water ........ 54
Boarding and starting in shallow water .... 54
Boarding with passengers ........................ 55
Bow eye ................................................... 28
Builder’s plate............................................. 2
C
Capsized watercraft ................................. 57
Check engine warning indicator ............... 34
Cleaning the watercraft ............................ 65
Cooling water pilot outlet .................... 26, 48
Craft Identification Number (CIN) ............... 1
Cruising limitations ................................... 10
D
Docking the watercraft ............................. 60
E
Emergency procedures ............................ 80
Engine break-in ........................................ 49
Engine compartment ................................ 42
Engine oil ................................................. 39
Engine oil and oil filter .............................. 70
Engine oil level ......................................... 42
Engine overheat warning indicator ........... 33
Engine serial number ................................. 1
Engine shut-off cord ................................. 47
Engine shut-off switch .............................. 25
Engine stop switch ................................... 25
Enjoy your watercraft responsibly ............ 18
F
Fire extinguisher....................................... 45
Flushing the cooling system ..................... 63
Front storage compartment ...................... 35
Fuel and oil............................................... 38
Fuel injection system................................ 75
Fuel level .................................................. 42
Fuel level meter........................................ 31Fuel level warning indicator ...................... 32
Fuel system .............................................. 64
Fuel system, checking .............................. 70
Fuel tank .................................................. 70
Fuel tank filler cap .................................... 24
Fuel tank, filling ........................................ 39
Fuses, replacing ....................................... 82
G
Gasohol .................................................... 38
Gasoline ................................................... 38
Getting to know your watercraft ............... 52
Glove compartment .................................. 36
H
Handgrip ................................................... 28
Hazard information ................................... 14
Hood ......................................................... 23
Hour meter/voltmeter ............................... 32
Hull and deck ........................................... 42
I
Identification numbers ................................ 1
Important labels .......................................... 3
J
Jet intake .................................................. 47
Jet intake and impeller, cleaning .............. 80
Jet thrust nozzle angle, checking ............. 71
Jumper cables, connecting ...................... 81
L
Labels, other .............................................. 7
Labels, warning .......................................... 4
Launching the watercraft .......................... 49
Learning to operate your watercraft ......... 52
Leaving the watercraft .............................. 51
Limitations on who may operate the
watercraft ................................................ 9
“L-MODE” indicator light (for VX Deluxe/
VX Cruiser) ........................................... 35
Lubrication................................................ 64
Lubrication points ..................................... 73
M
Main components, location of .................. 19
Maintenance and adjustments ................. 66
Model information....................................... 2
Multifunction information center ......... 30, 48
O
Oil pressure warning indicator .................. 32
UF1K73E0.book Page 1 Wednesday, July 11, 2007 9:15 AM