Page 17 of 80
Pushing the “TRIP” button switches
the display between the odometer
mode “ODO” and the tripmeter mode
“TRIP”. To reset the tripmeter, enter
the “TRIP” mode, and then hold down
the “TRIP” button for at least one
second. The tripmeter can be used
together with the fuel gauge to esti-
mate the distance that can be trave-
led with a full tank of fuel. This infor-
mation will enable you to plan future
fuel stops.
Setting the odometer/tripmeter
reading mode
The odometer and tripmeter can be
set to count in either kilometers or
miles according to the following pro-
cedure.
1. Turn the key to “
f” while pres-
sing the reset button.
2. Release the reset button when
the display comes on.
3. The current mode appears in the
display: “CONT” (continental) for
the kilometer mode and “EnGL”
(English) for the mile mode.
4. Press the reset button to switch
the mode.5. Press the reset button for two
seconds to confirm the setting.
NOTE:
The odometer/tripmeter reading
mode can be changed any num-
ber of times while the odometer
reading is below 10 (km/h or
MPH), but it cannot be changed
anymore after the reading has
reached 10 (km/h or MPH).
Switching between the kilometer
mode and the mile mode does
not change or convert the current
odometer/tripmeter reading.
EAUM1100
Battery voltage/fuel gauge
1. Fuel gauge
2. Battery voltage
When the key is turned to “e”, the
voltage/fuel gauge indicates the bat-
tery voltage.
NOTE:
If the battery voltage drops to 10 V,
have a Yamaha dealer check the bat-
tery.
When the key is turned to “f”, the
voltage/fuel gauge indicates the
amount of fuel in the fuel tank after
indicating the battery voltage for two
seconds. The needle moves towards
“E” (empty) as the fuel level decrea-
1
2
y3
INSTRUMENT AND CONTROL FUNCTIONS
3-3
5D8-F819D-E0.qxd 1/6/07 17:30 Página 17
Page 45 of 80
2. Place an oil pan under the engine
to collect the used oil.
3. Remove the engine oil filler cap
and the engine oil drain bolt to
drain the oil from the crankcase.
1. Engine oil drain bolt
2. Washer
4. Check the washer for damage
and replace it if necessary.
5. Install the washer and the engine
oil drain bolt, and then tighten the
drain bolt to the specified torque.
NOTE:
Make sure that the washer is properly
seated.
6. Add the specified amount of the
recommended engine oil, and
then install and tighten the oil
filler cap.
ECA11670
CAUTION:
Do not use oils with a diesel
specification of “CD” or oils of
a higher quality than specified.
In addition, do not use oils
labeled “ENERGY CONSER-
VING II” or higher.
Be sure no foreign material
enters the crankcase.
7. Start the engine, and then let it
idle for several minutes while
checking it for oil leakage. If oil is
leaking, immediately turn the
engine off and check for the cau-
se.
8. Reset the oil change indicator
display according to the follo-
wing procedure.
To reset the oil change indicator
display
1. Push and hold the "TRIP" button
for a MAXIMUM of three
seconds. While pushing the
"TRIP" button, turn the key to
"f".
Recommended engine oil:
See page 8-1.
Oil change quantity:
1.2 L (1.27 US qt) (1.06 Imp.qt)
Tightening torque:
Engine oil drain bolt:
32 Nm (3.2 m•kgf, 23.1 ft•lbf)
2
1
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-10
5D8-F819D-E0.qxd 1/6/07 17:30 Página 45
Page 46 of 80
2. Release the "TRIP" button and
the oil change indicator light will
go off.
3. Turn the key to "e".
NOTE:
If the engine oil is changed before the
oil change indicator light comes on
(i.e. before the periodic oil change
interval has been reached), the indi-
cator light must be reset after the oil
change for the next periodic oil chan-
ge to be indicated at the correct time.
To reset the oil change indicator light
before the periodic oil change interval
has been reached, follow the above
procedure, but note that the indicator
light will come on for 1.4 seconds
after releasing the reset button, other-
wise repeat the procedure.
EAU20061
Final transmission oil
The final transmission case must be
checked for oil leakage before each
ride. If any leakage is found, have a
Yamaha dealer check and repair the
scooter. In addition, the final trans-
mission oil must be changed as
follows at the intervals specified in the
periodic maintenance and lubrication
chart.
1. Start the engine, warm up the
final transmission oil by riding the
scooter for several minutes, and
then stop the engine.
2. Place the scooter on the centers-
tand.
3. Place an oil pan under the final
transmission case to collect the
used oil.
1. Final trasmission oil filler cap
1. Final transmission oil drain bolt
4. Remove the oil filler cap and
drain bolt to drain the oil from the
final transmission case.
5. Install the final transmission oil
drain bolt, and then tighten it to
the specified torque.
1
1
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-11
5D8-F819D-E0.qxd 1/6/07 17:30 Página 46