2008 TOYOTA TUNDRA ESP

343
2008 TUNDRA from Apr. ’08 Prod. (OM 34477U)
For example, nearby buildings and terrain
can interfere with FM reception. Power
lines or telephone wires can interfere with
AM signals. And of course, radio signals
have a limited range. The farther you are
from a station, the weaker its signal will
be. In addition, reception conditions
change constantly as your vehicle moves.
Here are some common reception prob-
lems that probably do not indicate a prob-
lem with your radio:
FM
Fading and drifting stations—Generally, the
effective range of FM is about 40 km (25
miles). Once outside this range, you may
notice fading and drifting, which increase
with the distance from the radio transmit-
ter. They are often accompanied by distor-
tion.
Multi−path—FM signals are reflective,
making it possible for two signals to reach
your antenna at the same time. If this
happens, the signals will cancel each oth-
er out, causing a momentary flutter or
loss of reception.
Static and fluttering—These occur when
signals are blocked by buildings, trees, or
other large objects. Increasing the bass
level may reduce static and fluttering. Station swapping—If the FM signal you
are listening to is interrupted or weak-
ened, and there is another strong station
nearby on the FM band, your radio may
tune in the second station until the origi-
nal signal can be picked up again.
AM
Fading—AM broadcasts are reflected by
the upper atmosphere—especially at night.
These reflected signals can interfere with
those received directly from the radio sta-
tion, causing the radio station to sound
alternately strong and weak.
Station interference—When a reflected sig-
nal and a signal received directly from a
radio station are very nearly the same
frequency, they can interfere with each
other, making it difficult to hear the broad-
cast.
Static—AM is easily affected by external
sources of electrical noise, such as high
tension power lines, lightening, or electri-
cal motors. This results in static.
XM
∗
Alternation or modifications carried out
without appropriate authorization may in-
validate the user ’s right to operate the
equipment.
∗: Use of satellite radio requires XM
tuner and service. Contact your Toyota
dealer for details.
NOTICE
This equipment has been tested and
found to comply with the limits for a
class B digital device, pursuant to
Part 15 of the FCC Rules. These lim-
its are designed to provide reasonable
protection against harmful interfer-
ence in a residential installation. This
equipment generates, uses and can
radiate radio frequency energy and, if
not installed and used in accordance
with the instructions, may cause
harmful interference to radio commu-
nications. However, there is no guar-
antee that interference will not occur
in a particular installation.

346
2008 TUNDRA from Apr. ’08 Prod. (OM 34477U)
NOTICE
Do not use special shaped, trans-
parent/translucent, low quality or la-
beled discs such as those shown in
the illustrations. The use of such
discs may damage the player or
changer, or it may be impossible to
eject the disc.
 This system is not designed for use
of Dual Disc. Do not use Dual Disc
because it may cause damage to
the player or changer.
Correct Wrong
Handle the discs carefully, especially
when you are inserting them. Hold
them on the edge and do not bend
them. Avoid getting fingerprints on
them, particularly on the shiny side.
Dirt, scratches, warping, pin holes, or
other disc damage could cause the
player to skip or to repeat a section of
a track. (To see a pin hole, hold the
disc up to the light.)
Remove discs from the compact disc
player when you are not playing them.
Store them in their plastic cases away
from moisture, heat, and direct sun-
light.
To clean a disc: Wipe it with a soft, lint −
free cloth that has been dampened with
water. Wipe in a straight line from the
center to the edge of the disc (not in
circles). Dry it with another soft, lint −free
cloth. Do not use a conventional record
cleaner or anti −static device.

352
2008 TUNDRA from Apr. ’08 Prod. (OM 34477U)
The system may not function in the follow-
ing conditions and places:
The cellular phone is turned off.
The current position is outside the
communication area.
The cellular phone is not connected.
The cellular phone has a low battery.
The cellular phone is hiding behind the
seat or in the glove box and console
box.
The cellular phone touches or is cov-
ered with metal materials.
This system supports the following ser-
vice.
HFP (Hands Free Profile) Ver.1.0.
OPP (Object Push Profile) Ver.1.1.
If your cellular phone does not support
HFP, you cannot enter the Bluetooth

phone, and take OPP service individually.
Bluetooth is a registered trademark of
Bluetooth SIG. Inc. When transferring ownership of the ve-
hicle:
A lot of personal data is registered
when you use the handsfree system.
When transferring ownership of the ve-
hicle, initialize the system.
If you initialize it, the former state will
never come back again. Pay much atten-
tion when initializing the data.
You can initialize the following data in the
system.
Phone book data
Dialed numbers and received calls
Speed dial
Bluetooth phone data
Security code
FCC ID: HYQBTAU01A
IC ID: 1551ABTAU01A
MADE IN MEXICO
This device complies with Part 15 of the
FCC Rules and RSS
−210. Operation is
subject to the following two conditions:
(1) This device may not cause harmful
interference, and (2) this device must
accept any interference received, includ-
ing interference that may cause unde-
sired operation.
CAUTION
Changes or modifications not ex-
pressly approved by the party respon-
sible for compliance could void the
user’s authority to operate the equip-
ment.

368
2008 TUNDRA from Apr. ’08 Prod. (OM 34477U)
(c) Call History
1. Push the talk switch and say “Call history”, or turn the “AUDIO/CONTROL”
knob until “Call history” is displayed
and push the knob.
“Call history. Push the talk switch and say
incoming or outgoing.” is heard and “Call
History” is displayed. 2. Select one of the following:
Incoming
Outgoing
Incoming
1. Push the talk switch and say “Incoming”, or turn the
“AUDIO/CONTROL” knob until
“Incoming” is displayed and push the
knob.
“Most recent incoming call was XXXX” is
heard and the incoming number is dis-
played.
“Push the talk switch and say confirm.
Otherwise, say previous, or go back.” is
heard. 2. Follow voice guidance instructions, or turn the “AUDIO/CONTROL” knob until
the dial number that you want to regis-
ter is displayed and push the knob.
Next, input a voice tag.
For further details, see page 366. Outgoing
1. Push the talk switch and say “Outgoing”, or turn the
“AUDIO/CONTROL” knob until
“Outgoing” is displayed and push the
knob.
“Most recent outgoing call was XXXX” is
heard and the outgoing number is dis-
played.
“Push the talk switch and say confirm.
Otherwise, say previous, or go back.” is
heard. 2. Follow voice guidance instructions, or turn the “AUDIO/CONTROL” knob until
the dial number that you want to regis-
ter is displayed and push the knob.
Next, input a voice tag.
For further details, see 366. (d) Manual Input
1. Turn the “AUDIO/CONTROL” knob until “Manual Input” is displayed and push
the knob.
2. Turn the “AUDIO/CONTROL” knob to select a number. Push the
“AUDIO/CONTROL” knob to set.
3. When the number is set, push the “AUDIO/CONTROL” knob.
Next, input a voice tag.
For further details, see page 366.
INFORMATION
 The system can recognize single
digits from zero to nine # (pound),
∗ (star), and + (plus). Numbers that
are ten or greater are not recog-
nized.
 To speed up input, it is a good idea
to group all digits into a continuous
string. However, you can enter each
digit individually or group digits to-
gether in preferred string lengths.
The display corresponding to each op-
eration appears on the screen as fol-
lows:

376
2008 TUNDRA from Apr. ’08 Prod. (OM 34477U)
If the cellular phone is not registered, this
system cannot be used. See page 356 for
registering a cellular phone. Make sure
that “BT” is displayed and get the cellular
phone ready to use.
There are 3 way to make a phone call
with this system.
Speed dial
A phone call can be made with a preset
button in which a phone number is regis-
tered. See page 372 for setting the preset
buttons.
Dial by Name
The system dials the numbers correspond-
ing to the spoken names registered in the
system.
Dial by Number
The system dials to the spoken numbers.
To make a phone call
Push the off −hook switch to turn the
hands −free system on. To speed dial
1. Push the preset button where the de- sired number is set. The name or tele-
phone number is displayed.
2. Push the off −hook switch to dial.
To dial by Name 1. Push the talk switch and say “Dial by name”.
“Dial by name. Please push the talk
switch and say the stored name, or say
list names.” is heard and “Dial by Name”
is displayed.
2. Push the talk switch and say “XXXX”, or turn the “AUDIO/CONTROL” knob
until the phone name that you want to
dial is displayed and push the knob. When using a voice command:
“XXXX Push the off
−hook switch to dial.
Otherwise, push the talk switch and say
dial, or go back.” is heard. After that, do
the one of the following:
Push the off −hook switch.
Push the talk switch and say “Dial”.
Turn the “AUDIO/CONTROL” knob until
“Dial” is displayed and push the knob.
When using the knob:
It calls the number.
The system may not function in the follow-
ing cases:
If there is no number registered in the
preset button.
If the system does not recognize the
voice command.
—Making a phone call

377
2008 TUNDRA from Apr. ’08 Prod. (OM 34477U)
INFORMATION
The phone numbers registered in
the phone book can be retrieved.
 The system does not recognize that
the voice tag is not registered in
the registered cellular phone. For
details about voice tags, see “To
add entry” on page 366.
 A shortcut to “Dial by name” is
available. Push the talk switch and
say “Dial XXX (name you want to
dial)”.
To dial by Number
1. Push the talk switch and say “Dial by Number”.
“Dial by number. Please push the talk
switch and say the number.” is heard and
“Dial by Num” is displayed. 2. Push talk switch and say “XXXX”.
“Push the off −hook switch to dial.
Otherwise, push the talk switch and say
dial, go back, or delete.” is heard.
To dial the number, do the one of the
following:
Push the off −hook switch.
Push the talk switch and say “Dial”.
Turn the “AUDIO/CONTROL” knob until
“Dial” is displayed and push the knob.
If the number exceeds 24 digits, the sys-
tem may not function properly.
INFORMATION
 The system can recognize single
digits from zero to nine, # (pound),
∗ (star), and + (plus). Numbers that
are ten or greater are not recog-
nized.
 To speed up input, it is a good idea
to group all digits into a continuous
string. However, you can enter each
digit individually or group digits to-
gether in preferred string lengths.
The display corresponding to each op-
eration appears on the screen as fol-
lows:
Input operation—
You say: “Nine, nine, five”
Voice output: “995 push the offhook
switch to dial. Otherwise, push the
talk switch and say dial, go back, or
delete.”
Display: “995”
You say: “Seven, three, four”
Voice output: “734 push the offhook
switch to dial. Otherwise, push the
talk switch and say dial, go back, or
delete.”

452
2008 TUNDRA from Apr. ’08 Prod. (OM 34477U)
Driving with tire chains installed.
Driving over the steps such as the
joints on the road.
Driving on roads where the road
surface is pitted or has other differ-
ences in surface height.
Install all 4 tires of specified size at
appropriate pressure: The antilock
brake system detects vehicle speeds
using the speed sensors for respec-
tive wheels’ turning speeds. The use
of tires other than specified may fail
to detect the accurate turning speed
resulting in a longer stopping dis-
tance.
LS20017
Ty p e A
LS20018
Ty p e B
“ABS” warning light
The light comes on when the engine
switch is turned to the “ON” position. If
the anti −lock brake system and the brake
assist system work properly, the light
turns off after a few seconds. Thereafter,
if either of the systems malfunctions, the
light comes on again.
When the “ABS” warning light is on (and
the brake system warning light is off), the
following systems do not operate, but the
brake system still operates conventionally.
Anti −lock brake system
Brake assist system
Traction control system
“AUTO LSD” system
Vehicle stability control system
When the “ABS” warning light is on (and
the brake system warning light is off), the
anti −lock brake system does not operate
so that the wheels will lock up during a
sudden braking or braking on slippery
road surfaces.

461
2008 TUNDRA from Apr. ’08 Prod. (OM 34477U)
Temperature A, B, C—T he tem per a-
ture grades are A (the highest), B,
and C, representing the tire’s resis-
tance to the generation of heat and
its ability to dissipate heat when
tested under controlled conditions on
a specified indoor laboratory test
wheel. Sustained high temperature
can cause the material of the tire to
degenerate and reduce tire life, and
excessive temperature can lead to
sudden tire failure. The grade C cor-
responds to a level of performance
which all passenger car tires must
meet under the Federal Motor Vehicle
Safety Standard No.109. Grades B
and A represent higher levels of per-
formance on the laboratory test wheel
than the minimum required by law.
Warning: The temperature grades for
this tire are established for a tire that
is properly inflated and not over-
loaded. Excessive speed, underinfla-
tion, or excessive loading, either sep-
arately or in combination, can cause
heat buildup and possible tire failure.