’08 Solara_U (L/O 0802)
215
2008 CAMRY SOLARA from Feb. ’08 Prod. (OM33810U)
If the cellular phone is not registered, this
system cannot be used. See page 195 for
registering a cellular phone. Make sure
that [BT] is displayed and get the cellular
phone ready to use.
There are 3 ways to make a phone call
with this system.
Speed dial
A phone call can be made with a preset
button in which a phone number is regis-
tered. See page 211 for setting the preset
buttons.
Dial by Name
The system dials the numbers correspond-
ing to the spoken names registered in the
system.
Dial by Number
The system dials to the spoken numbers.
To make a phone call
Push the off −hook switch to turn the
hands −free system on. To speed dial
1. Push the preset button where the de- sired number is set. The name or tele-
phone number is displayed.
2. Push the off −hook switch to dial.
To dial by Name 1. Push the talk switch and say [Dial by name].
[Dial by name. Please push the talk
switch and say the stored name, or say
list names.] is heard and [Dial by Name]
is displayed.
2. Push the talk switch and say the phone name, or turn the “AUDIO CON-
TROL” knob until the name that you
want to dial is displayed and push the
knob. When using a voice command:
[XXXX (phone number) Push the off
−hook
switch to dial. Otherwise, push the talk
switch and say dial, or go back.] is heard.
After that, do the one of the following:
Push the off −hook switch.
Push the talk switch and say [Dial].
Turn the “AUDIO CONTROL” knob until
[Dial] is displayed and push the knob.
When using the knob:
It calls the number.
The system may not function in the follow-
ing cases:
If there is no number registered in the
preset button.
If the system does not recognize the
voice command.
—Making a phone call
’08 Solara_U (L/O 0802)
240
2008 CAMRY SOLARA from Feb. ’08 Prod. (OM33810U)
The displayed value is updated every 2
seconds.
Note that an accurate figure may not be
shown in the following cases.
When the vehicle is stopped with the
engine running, the display will indicate
the extremely high fuel consumption.
When the vehicle is driving down a
long slope, applying the engine brake,
the display will indicate the extremely
low fuel consumption.
The calculation is reset when the engine
switch is turned off. 2. Average fuel consumption (“AVG. MPG” or “AVG. L/100 km”)
Average fuel consumption is calculated
and displayed based on total driving
distance and total fuel consumption
with the engine running.
The displayed value is updated every 10
seconds.
To reset the calculations, push and hold
the “DISP” button for more than 1 second. 3. Driving range
(“RANGE MI” or “RANGE km”)
The distance the vehicle can travel with
the remaining fuel is calculated and
displayed based on the quantity of re-
maining fuel and past fuel consumption.
The driving range display indicates the
approximate distance that you can drive
until the fuel gauge reaches “E”. It is
different from the actual distance traveled.
The displayed value is updated every time
the fuel equivalent for 1 mile or 1 km is
consumed.
Every time you refuel the vehicle, the cal-
culation is reset. However, when only a
small amount of fuel is added to the tank,
the display may not be reset.
The actual driving range varies with driv-
ing habits and road conditions. If fuel con-
sumption is good, the driving range will be
longer. If fuel consumption is poor, the
driving range will be shorter.
If the low fuel level warning light comes
on, refuel even if the display indicates
that the vehicle can be driven further. 4. Average vehicle speed
(“AVG. MPH” or “AVG. km/H”)
Average vehicle speed is calculated and
displayed based on total driving dis-
tance and total driving time with the
engine running.
The displayed value is updated every 10
seconds.
To reset the calculations, push and hold
the “DISP” button for more than 1 second.
5. Elapsed time (“E/T”)
The elapsed time after the engine starts
is displayed.
When the engine is started, driving time
is counted from 0:00. Up to 99:59 (99
hours, 59 minutes) can be displayed.
When the driving time exceeds 99:59, the
counter returns to 0:00.
To reset the calculations, push and hold
the “DISP” button for more than 1 second.
’08 Solara_U (L/O 0802)
241
2008 CAMRY SOLARA from Feb. ’08 Prod. (OM33810U)
The center display indicates the time
when the engine switch is in the “ACC”
or “ON” position.
To reset the hour: Push the “H” button.
To reset the minutes: Push the “M” button.The right side display indicates the out-
side air temperatures when the engine
switch is in the “ON” position.
The displayed temperature ranges from
−30 C ( −22 F) up to 50 C (122 F).
If an abnormality exists in the connection
of the outside air temperature sensor, “ −−”
will appear on the display. If “ −−” appears
on the display, contact your Toyota dealer.
There may be a case that “−−” appears
momentarily when the ignition is quickly
turned to “ON”. It is normal if it goes out
soon.The direction is indicated on the inside
rear view mirror.
If the engine switch was turned off with
the system on, the system will automati-
cally turn back on when the engine switch
is turned on.
Push the “AUTO” switch for longer than 3
seconds to turn the compass system on
and off.
—Clock —Outside temperatureCompass
