2008 TOYOTA SOLARA clock

’08 Solara_U (L/O 0802)
252
2008 CAMRY SOLARA from Feb. ’08 Prod. (OM33810U)
To use the glove box:
Open by pulling the lever.
Lock by inserting the master key and turn-
ing it clockwise.
Unlock by inserting the master key and
turning it counterclockwise.
With the instrument panel lights on, the
glove box light will come on when the
glove box is open.
CAUTION
To reduce the chance of injury in
case of an accident or a sudden stop,
always keep the glove box door
closed while driving.
Center console
Over head console
Glove boxAuxiliary boxes

’08 Solara_U (L/O 0802)
308
2008 CAMRY SOLARA from Feb. ’08 Prod. (OM33810U)
To remove the jack, turn the jack joint
counterclockwise by hand until the
jack becomes free.To st or e the jac k , align the hole o f t he
jack head with the vehicle hook. Turn
the jack joint cloc k wis e unt il the jac k
base fits securely with the vehicle
body.
This prevents the jack from flying for-
ward during a collision or sudden
stop.Ty p e A
Ty p e B

’08 Solara_U (L/O 0802)
310
2008 CAMRY SOLARA from Feb. ’08 Prod. (OM33810U)
4. Loosen all the wheel nuts.
Always loosen the wheel nuts before
raising the vehicle.
Turn the wheel nuts counterclockwise
to loosen. To get maximum leverage,
fit the wrench to the nut so that the
handle is on the right side, as shown
above. Grab the wrench near the end
of the handle and pull up on the han-
dle. Be careful that the wrench does
not slip off the nut.
Do not remove the nuts yet—just un-
screw them about one −half turn.
CAUTION
Never use oil or grease on the
bolts or nuts. The nuts may loose
and the wheels may fall off,
which could cause a serious ac-
cident.
5. Position the jack at the correct
jack point as shown. Rotate the
load rest 90  from storage posi-
tion to lifting position.
Make sure the jack is positioned on
a level and solid place.
—Loosening wheel nuts —Positioning the jack

’08 Solara_U (L/O 0802)
311
2008 CAMRY SOLARA from Feb. ’08 Prod. (OM33810U)
6. After making sure that no oneis in the vehicle, raise it high
enough so that the spare tire
can be installed.
Remember you will need more ground
clearance when putting on the spare
tire than when removing the flat tire.
To raise the vehicl e, insert the jack
handle into the jack (it is a loose fit)
and turn it clockwise. As the jack
touches the vehicle and begins to lift,
double −check that it is properly posi-
tioned.
CAUTION
Never get under the vehicle when
the vehicle is supported by the
jack alone.
7. Remove the wheel nuts and change tires.
Lift the flat tire straight off and put it
aside.
Roll the spare wheel into position and
align the holes in the wheel with the
bolts. Then lift up the wheel and get
at least the top bolt started through
its hole. Wiggle the tire and press it
back over the other bolts.
—Raising your vehicle —Changing wheels

’08 Solara_U (L/O 0802)
313
2008 CAMRY SOLARA from Feb. ’08 Prod. (OM33810U)
9. Lower the vehicle completelyand tighten the wheel nuts.
Turn the jack handle counterclock-
wise to lower the vehicle.
Use only the wheel nut wrench to
tighten the nuts. Do not use other
tools or any additional leverage other
than your hands, such as a hammer,
pipe or your foot. Make sure the
wrench is securely engaged over the
nut.
Tighten each nut a little at a time in
the order shown. Repeat the process
until all the nuts are tight.
CAUTION
 When lowering the vehicle,
make sure all portions of your
body and all other persons
around will not be injured as
the vehicle is lowered to the
ground.
 Have the wheel nuts tightened
with torque wrench to 103 N·m
(10.5 kgf·m, 76 ft·lbf), as soon
as possible after changing
wheels. Otherwise, the nuts
may loosen and the wheels
may fall off, which could cause
a serious accident.
 Do not attach a heavily dam-
aged plastic wheel ornament.
It may fly off the wheel and
cause accidents while the ve-
hicle is moving.
10.Reinstall the wheel ornament.
1. Put the wheel ornament into posi- tion.
Align the cutout of the wheel orna-
ment with the valve stem as shown. 2. Press hand firmly on one side of wheel ornament and then firmly
tap the other side around the edge
of wheel ornament with the heel
of your hand to snap into place.
—Lowering your vehicle —Reinstalling wheel ornament
(steel wheels)

’08 Solara_U (L/O 0802)
349
2008 CAMRY SOLARA from Feb. ’08 Prod. (OM33810U)
Clean all dirt from the outside of the res-
ervoir tank and look at the fluid level. If
the fluid is cold, the level should be in the
“COLD” range. Similarly, if it is hot, the
fluid level should be in the “HOT” range.
If the level is at the low side of either
range, add automatic transmission fluid
DEXRONII or III to bring the level within
the range.
To remove the reservoir cap, turn it coun-
terclockwise and lift up. To reinstall it,
turn it clockwise. After replacing the reser-
voir cap, visually check the steering box
case, vane pump and hose connections
for leaks or damage.
CAUTION
The reservoir tank may be hot so be
careful not to burn yourself.
NOTICE
Avoid overfilling, or the power steer-
ing could be damaged.
Keep your tire inflation pressures
at the proper level.
The recommended cold tire inflation
pressures, tire sizes and the com-
bined weight of occupants and cargo
(vehicle capacity weight) are de-
scribed on pages 372 and 377. They
are also on the tire and loading infor-
mation label.
You should check the tire inflation
pressure every two weeks, or at least
once a month. And do not forget the
spare!
Checking tire inflation
pressure

’08 Solara_U (L/O 0802)
365
2008 CAMRY SOLARA from Feb. ’08 Prod. (OM33810U)
Light bulbsBulbNo.WTy p e
Headlights (low) With discharge
headlights
Without
discharge
headlights
—
35
55A
B
Headlights
(high beam)—65C
Front fog lights—55B
Parking, front
side marker and
front turn signal
lights
3457NA30/8E
Rear turn signal
lightsT20NA21E
Back −up lights92116D
License plate
lights1943.8D
High mounted
stoplight (coupe)92117.9D
Personal lights
(coupe)—5D
Light bulbsBulb
No.WTy p e
Personal lights
(convertible)—8F
Interior light—8G
Vanity lights
(coupe)—1.4G
Vanity lights
(convertible)—1.5F
Glove box light—1.2D
Quarter trim
courtesy light1943.8F
Trunk light
(coupe)28255D
Trunk light
(convertible)—3.8D
A: D4S discharge bulbs
B: H11 halogen bulbs
C: HIR1 halogen bulbs
D: Wedge base bulbs (clear)
E: Wedge base bulb (amber)
F: Single end bulbs
G: Double end bulbs
1. Open the hood. Turn the bulb cover counterclockwise and remove it.
—Low beam headlights
(except discharge headlights)

’08 Solara_U (L/O 0802)
366
2008 CAMRY SOLARA from Feb. ’08 Prod. (OM33810U)
2. Turn the bulb base counterclockwiseto the front of the vehicle as shown.
The above illustration shows the left −hand
headlight.3. Unplug the connector while depress- ing the lock release.
If the connector is tight, wiggle it.4. Plug in a new bulb into the connec- tor and install it into the mounting
hole.
Aiming is not necessary after replacing
the bulb. When aiming adjustment is nec-
essary, contact your Toyota dealer.