2008 TOYOTA SIENNA key

08 SIENNA_U (L/O 0801)
200
2008 SIENNA from Aug. ’08 Prod. (OM45455U)
If the light is flashing, we recommend that
you replace the engine oil at an early
opportunity depending on the driving and
road conditions. If the light comes on,
replace it as soon as possible.
The system must be reset after the en-
gine oil replacement. Reset the system by
the following procedure:1. Turn the engine switch to the “ACC” or “LOCK” position with the odometer
reading shown. (For details, see
“Odometer and two trip meters” on
page 190 in this Section.)
2. Turn the engine switch to the “ON” position while holding down the trip
meter reset button.
Hold down the button for at least 5 sec-
onds. The odometer indicates “000000”
and the light goes off.
If the system fails to reset, the light will
continue flashing. (o) Third Seats Warning Light and
Buzzer
“3RD SEAT” warning light (instrument
cluster)—
This light warns that the third seat opera-
tion is not yet complete. Complete the
third seat operation. For details, see
“—Folding third seats” on page 98 or
“—Stowing third seats” on page 101 in
Section 1 −3.
Third seats warning light and buzzer
(switch)—
This light warns that the third seat opera-
tion is not yet completed.
When flashing—An object may be caught
between the seat and seatback.
When illuminated—An object may be
caught between the seat and floor or
switch is released during the operation.
Remove the object and then operate
again. If nothing is caught when flashing,
contact your Toyota dealer. (p) Dynamic Laser Cruise Control Mas-
ter Warning Light
This light warns that there is a problem
somewhere in the dynamic laser cruise
control system.
The light will come on when the engine
switch is turned to “ON” and go off after
a few seconds.
When the light comes on, the alarm
sounds and the warning code will appear
on the display. At this time, dynamic laser
cruise control is cancelled. For details,
see “Dynamic laser cruise control” on
page 225 in Section 1 −7.
(q) Key Reminder Buzzer
This buzzer acts as a reminder to remove
the key when you open the driver’s door
with the engine switch in the “ACC” or
“LOCK” position.

08 SIENNA_U (L/O 0801)
204
2008 SIENNA from Aug. ’08 Prod. (OM45455U)
“START”—Starter motor on. The key
will return to the “ON” position when
released.
For starting tips, see page 451 in Section
3.
“ON”—Engine on and all accessories
on.
This is the normal driving position.
“ACC”—Accessories such as the radio
operate, but the engine is off.
If you leave the engine switch in the
“ACC” or “LOCK” position and open the
driver ’s door, a buzzer will remind you to
remove the key.“LOCK”—Engine is off and the steering
wheel is locked. The key can be re-
moved only at this position.
You must push in the key to turn the
engine switch from “ACC” to the “LOCK”
position. The selector lever must be put
in the “P” position before pushing the key.
Vehicles with engine immobilizer system—
Once you remove the key, the engine im-
mobilizer system is automatically set. (See
“Engine immobilizer system” on page 13
in Section 1−
2.)
When starting the engine, the engine
switch may seem stuck at the “LOCK”
position. To free it, first be sure the key
is pushed all the way in, and then rock
the steering wheel slightly while turning
the key gently.
Approximately five hours after the engine
is turned off, you may hear sound coming
from under the floor around the driver ’s
seat for several minutes. This is normal
operation and does not indicate a malfunc-
tion. (See “Leak detection pump” on page
viii.)
It is not a malfunction if the needle on all
meters and gauges move slightly when the
engine switch is turned to the “ACC”,
“ON” or “START” position.
NOTICE
Do not leave the engine switch in the
“ON” position if the engine is not
running. The battery will discharge
and the ignition could be damaged.
Engine (ignition) switch

08 SIENNA_U (L/O 0801)
205
2008 SIENNA from Aug. ’08 Prod. (OM45455U)
Your automatic transmission has a shift
lock system to minimize the possibility of
incorrect operation. This means you can
only shift out of “P” position when the
brake pedal is depressed (with the engine
switch in the “ON” position).
(a) Selector lever
The shift position is also displayed on the
instrument cluster.
P:Parking, engine starting and key
removal
R: Reverse
N: Neutral
D: Normal driving
(shifting into overdrive possible)
4: Engine braking
(shifting into overdrive not possible)
3, 2: Stronger engine braking
L: Maximum engine braking
Automatic transmission
Selector lever
Shift normally. Shift with the brake pedal
depressed. (The engine switch
must be in the “ON” position.)

08 SIENNA_U (L/O 0801)
316
2008 SIENNA from Aug. ’08 Prod. (OM45455U)
Phone Setup (see page 322)
Pair phone
To use the hands−free system, you
need to register your phone in the sys-
tem.
Change name
The registered phone names can be
changed.
Delete
The registered phones can be deleted.
List phones
The registered phone names can be
checked.
Select phone
The registered phones can be selected.
Set passkey
The passkey used to register the
phone can be changed. Security (see page 327)
Set PIN
The PIN can be set or changed.
Phone book lock
The phone book can be locked.
Phone book unlock
The locked phone book can be un-
locked.
System Setup (see page 331)
Adjust Guidance Volume
Guidance volume can be adjusted.
Initialize
Phone Book (see page 331)
Add Entry
Phone numbers and voice tags can be
registered.
Change Name
The registered names can be changed.
Delete Entry
The registered names can be deleted.
Delete Speed Dial
The registered speed dial can be de-
leted.
List names
The registered names can be checked.
Set Speed Dial
Speed dials can be set
Redial (see page 339)
Callback (see page 340)
Making a phone call (see page 342)
Receiving a phone call (see page 344)
Talking on the phone (see page 345)
Handsfree phone system
(type 22 audio only)—
—Reference

08 SIENNA_U (L/O 0801)
323
2008 SIENNA from Aug. ’08 Prod. (OM45455U)
Set PassKey
The passkey can be c hanged. A 4 to 8
digit code can be input as a pa sskey.
Delete
The registered phones can be deleted.
To enter the phone setup menu 1. Push the off −hook switch to turn the
hands −free system on.
2. Follow voice guidance instructions, or turn the “AUDIO CONTROL” knob until
“Setup” is displayed and push the
knob.
“Setup. Please push the talk switch and
say security, or phone setup.” is heard. 3. Follow voice guidance instructions, or turn the “AUDIO CONTROL” knob until
“Phone Setup” is displayed and push
the knob.
“Phone setup. Push the talk switch and
say pair phone, select phone, change
name, list phones, set pa sskey or delete.”
is heard.
“XXX (phone name) already selected.” is
heard and “XXX (phone name)” is dis-
played.
If no phone has been registered, the sys-
tem may not function properly. To pair phones
1. Push the talk switch and say “Pair phone”, or turn the “AUDIO CONTROL”
knob until “Pair Phone” is displayed
and push the knob.
“Pair. Push the talk switch and say a
name for the phone.” is heard. 2. Follow voice guidance instructions, or turn the “AUDIO CONTROL” knob until
“Record Name” is displayed, push the
knob and say “XXX (desired phone
name)”.
“Push the talk switch and say confirm.
Otherwise, say go back.” is heard. 3. Follow voice guidance instructions, or turn the “AUDIO CONTROL” knob until
“Confirm” is displayed and push the
knob.
“XXX Ready for phone pairing. Please use
the phone to connect it to the hands −free
system. The passkey for the p hone is....”
is heard.
After “HANDS FREE” is displayed, a pass-
key
∗ is displayed and “Searching.” is
heard.
4. Input the displayed passkey into the phone. “The phone is paired and ready for use.
Returning to the main menu.” is heard and
“Paired” is displayed.
The system may not function in the follow-
ing cases:
If 6 phones have already been regis-
tered.
If the vehicle is moving.
If the system cannot communicate with
the phone.
∗: Passkey is a password r
equired to reg-
ister a phone to the system.
INFORMATION
To use the handsfree system, you
need to register your phone in the
system. Once you have registered
it, you can make a handsfree call.
Up to 6 phones can be registered.
For the operation of the phone, see
the manual that comes with your
cellular phone.
The passkey can be changed. See
page 326 for changing the passkey.

08 SIENNA_U (L/O 0801)
326
2008 SIENNA from Aug. ’08 Prod. (OM45455U)
Select phone
Push the talk switch and say “Select
phone”, or turn the “AUDIO CONTROL”
knob until “Select Phone” is displayed and
push the knob.
For further details on selecting a phone,
see page 324.
Change name
Push the talk switch and say “Change
name”, or turn the “AUDIO CONTROL”
knob until “Change Name” is displayed
and push the knob.
For further details on changing a name,
see page 324.
Delete
Push the talk switch and say “Delete”, or
turn the “AUDIO CONTROL” knob until
“Delete” is displayed and push the knob.
For further details on deleting a phone,
see page 327.
If no phone has been registered, the sys-
tem may not function properly.To set a passkey
1. Push the talk switch and say “Set passkey”, or turn the “AUDIO
CONTROL” knob until “Set Passkey” is
displayed and push the knob.
“Set Passkey. The passkey is r equired for
the phone pairing process. Push the talk
switch and say a new passkey.” is heard
and passkey is displayed.
2. Follow voice guidance instructions, or turn the “AUDIO CONTROL” knob to
select a number.
When using a voice command:
“XXXX (new pa sskey) Push the talk switch
and say confirm. Otherwise, continue add-
ing numbers, or say go back or delete.”
is heard and “XXXX (new pa sskey)” is
displayed.
Follow voice guidance instructions, or turn
the “AUDIO CONTROL” knob until
“Confirm” is displayed and push the knob.
“Passkey ch anged. Returning to the phone
setup.” is heard. When using the knob:
1. Turn the “AUDIO CONTROL” knob to select a number. Push the “AUDIO
CONTROL” knob to set.
2. When the passkey is set, push the “AUDIO CONTROL” knob.
“Passkey c hanged. Returning to the phone
setup.” is heard.
The system does not function in the fol-
lowing cases:
If the passkey has less than 4 digits.
If the passkey has more than 8 digits.

08 SIENNA_U (L/O 0801)
398
2008 SIENNA from Aug. ’08 Prod. (OM45455U)
NOTICE
To prevent the battery from being
discharged, do not use the power
outlet longer than necessary when
the engine is not running.
 Close the power outlet lids when
the power outlets are not in use.
Inserting anything other than an ap-
propriate plug that fits the outlet,
or allowing any liquid to get into
the outlet may cause electrical fail-
ure or short circuits.
The power outlet is not designed for
the following electric appliances even
though their power consumption is un-
der 115 VAC/100W. These appliances
may not operate properly.
Appliances with high initial peak watt-
age: cathode− ray tube type televisions,
compressor −driven refrigerators, electric
pumps, electric tools, etc.
Measuring devices which process pre-
cise data: medical equipment, measur-
ing instruments, etc.
Other appliances requiring an extremely
stable power supply: microcomputer −
controlled electric blankets, touch sen-
sor lamps, etc. Certain electrical appliances may cause
radio noise.
To use the glove box:
Open by pulling the lever.
Lock by inserting the master key and turn-
ing it clockwise.
Unlock by inserting the master key and
turning it counterclockwise.
CAUTION
To reduce the chance of injury in
case of an accident or a sudden stop,
always keep the glove box door
closed while driving.
Glove box

08 SIENNA_U (L/O 0801)
465
2008 SIENNA from Aug. ’08 Prod. (OM45455U)
IN CASE OF AN EMERGENCY
In case of an emergency
If your vehicle will not start466
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
If your engine stalls while driving 469
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
If you cannot increase engine speed 469
. . . . . . . . . . . . . . . . . . . . . . . . . .
If your vehicle overheats 470
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . \
If you have a flat tire 471
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . \
. . . . .
If your vehicle becomes stuck 490
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
If your vehicle needs to be towed 490
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
If you lose your keys 492
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . \
. . . .
If you lose your wireless remote control transmitter 493
. . . . . . . . . . . . .
If you cannot shift automatic transmission selector lever 493
. . . . . . . .
If you cannot operate back door opener 494
. . . . . . . . . . . . . . . . . . . . . . .
SECTION 4