2008 TOYOTA RAV4 Engine

’08 Rav4_U (L/O 0802)
147
2008 RAV4 from Feb. ’08 Prod. (OM42726U)
Your automatic transmission has a shift
lock system to minimize the possibility of
incorrect operation. This means you can
only shift out of the “P” position when the
brake pedal is depressed (with the engine
switch in the “ON” position).
(a) Selector lever
The shift position is also displayed on the
instrument cluster.
P:Parking, engine starting and key
removal
R: Reverse
N: Neutral
D: Normal driving
(shifting into overdrive possible)
4: Engine braking
(shifting into overdrive not possible)
3, 2: Stronger engine braking
L: Maximum engine braking
Automatic transmission (5speed)
Shift normally. Selector lever
Shift with the brake pedal
depressed.
(The engine switch must
be in the “ON” position.)

’08 Rav4_U (L/O 0802)
148
2008 RAV4 from Feb. ’08 Prod. (OM42726U)
(b) Normal driving1. Start the engine as instructed in “How to start the engine” on page 342 in
Section 3. The transmission must be in
the “P” or “N” position.
2. With your foot holding down the brake pedal, shift the selector lever to the
“D” position.
When the lever is in the “D” position, the
automatic transmission system will select
the most suitable gear for running condi-
tions such as normal cruising, hill climb-
ing, hard towing, etc.
Always use the “D” position for better fuel
economy and quieter driving. If the engine
coolant temperature is low, the transmis-
sion will not shift into the overdrive gear
even in the “D” position.
CAUTION
Never put your foot on the accelera-
tor pedal while shifting.
3. Release the parking brake and brake pedal. Depress the accelerator pedal
slowly for smooth starting. (c) Using engine braking
To use engine braking, you can downshift
the transmission as follows:
Shift into the “4” position. The trans-
mission will downshift to fourth gear
and engine braking will be enabled.
Shift into the “3” position. The trans-
mission will downshift to third gear
when the vehicle speed drops down to
or lower than 161 km/h (100 mph),
and stronger engine braking will be en-
abled.
Shift into the “2” position. The trans-
mission will downshift to second gear
when the vehicle speed drops down to
or lower than 99 km/h (62 mph), and
stronger engine braking will be en-
abled.
Shift into the “L” position. The trans-
mission will downshift to first gear
when the vehicle speed drops down to
or lower than 42 km/h (26 mph), and
maximum engine braking will be en-
abled.
When the cruise control is being used,
even if you downshift from the “D” to “4”
position, engine braking will not be en-
abled because the cruise control is not
cancelled. For ways to decrease the vehicle speed,
see “Cruise control” on page 168 in this
Section.
CAUTION
Be careful when downshifting on a
slippery surface. Abrupt shifting
could cause the vehicle to skid or
spin.
(d) Using the “3”, “2” and “L” posi-
tions
The “3”, “2” and “L” positions are used for
strong engine braking as described pre-
viously.
With the selector lever in the “3”, “2” or
“L” position, you can start the vehicle in
motion as with the lever in the “D” posi-
tion.
With the selector lever in the “3” or “2”
position, the vehicle will start in first gear
and automatically shift to third gear or
second gear.
With the selector lever in the “L” position,
the transmission is engaged in first gear.

’08 Rav4_U (L/O 0802)
149
2008 RAV4 from Feb. ’08 Prod. (OM42726U)
NOTICE
Be careful not to overrev the en-
gine. Watch the tachometer to keep
engine rpm from going into the red
zone. The approximate maximum al-
lowable speed for each position is
given below for your reference:
“3” 175 km/h (109 mph). . . . . . . .
“2” 113 km/h (70 mph) . . . . . . . . .
“L” 63 km/h (39 mph) . . . . . . . . . .
 Do not continue hill climbing or
hard towing for a long time in the
“3”, “2” or “L” position. This may
cause severe automatic transmis-
sion damage from overheating. To
prevent such damage, the “4” posi-
tion should be used in hill climbing
or hard towing.
(e) Backing up
1. Bring the vehicle to a complete stop.
2. With the brake pedal held down with your foot, shift the selector lever to the
“R” position.
NOTICE
Never shift into reverse while the ve-
hicle is moving.
(f) Parking
1. Bring the vehicle to a complete stop.
2. Pull the parking brake lever up fully to securely apply the parking brake.
3. With the brake pedal pressed down, shift the selector lever to the “P” posi-
tion.
CAUTION
Never attempt to move the selector
lever into the “P” position under any
circumstances while the vehicle is
moving. Serious mechanical damage
and loss of vehicle control may re-
sult.
(g) Good driving practice
If the transmission repeatedly shifts up
and down between fourth gear and
overdrive when climbing a gentle slope,
shift the selector lever to the “4” posi-
tion. Be sure to shift the selector lever
to the “D” position immediately after-
ward.
When towing a trailer, in order to main-
tain engine braking efficiency, do not
use the “D” position.
CAUTION
Always keep your foot on the brake
pedal while stopped with the engine
running. This prevents the vehicle
from creeping.
NOTICE
Always use the brake pedal or the
parking brake to hold the vehicle on
an upgrade. Do not attempt to hold
the vehicle using the accelerator ped-
al, as this can cause the transmission
to overheat.

’08 Rav4_U (L/O 0802)
150
2008 RAV4 from Feb. ’08 Prod. (OM42726U)
(h) If you cannot shift the selector le-ver out of the “P” position
If you cannot shift the selector lever from
the “P” position even though the brake
pedal is depressed, use the shift lock
override button. For instructions, see “If
you cannot shift automatic transmission
selector lever” on page 378 in Section 4. The active torque control 4WD system
controls the engine torque that is ap-
plied to the rear wheels according to
the driving conditions and road condi-
tions. When the vehicle’s driving condi-
tions are stable such as driving straight
ahead, the engine torque is applied to
only the front wheels.
FOURWHEEL DRIVE LOCK SWITCH
When the vehicle is driven on loose
surfaces, such as sand, gravel, or deep
snow, or if the vehicle gets stuck,
pushing the fourwheel drive lock
switch to ensure that the engine torque
is applied to the 4 wheels.
When the four
−wheel drive lock switch is
pushed, the four −wheel drive lock indicator
light blinks twice and remains on until the
four −wheel drive lock is canceled.
To cancel the four −wheel drive lock, push
the switch once again and the four −wheel
drive lock indicator light will go off.
Active torque control 4WD
system

’08 Rav4_U (L/O 0802)
151
2008 RAV4 from Feb. ’08 Prod. (OM42726U)
When the vehicle speed exceeds 40 km/h
(25 mph), the four−wheel drive lock will
be cancelled automatically.
The four −wheel drive lock indicator will
come on for a few seconds when the
engine switch is turned to the “ON” posi-
tion.
If the indicator light does not come on
when the engine switch is turned to the
“ON” position or the four −wheel drive lock
switch is pushed, contact your Toyota
dealer.
NOTICE
Use the fourwheel drive lock only
when driving on the loose surfaces,
such as sand, gravel, or deep snow,
or if the vehicle gets stuck. After the
fourwheel drive lock is used to pro-
vide traction, cancel the fourwheel
drive lock. Using the fourwheel drive
lock at other times may cause dam-
age to the fourwheel drive system.
SYSTEM FAILURE WARING
The “4WD” warning light warns that there
is a problem somewhere in the active
torque control 4WD system.
The light will come on when the engine
switch is turned to the “ON” position.
When the system works properly, the light
turns off after a few seconds.
If the warning light does not come on
when the engine switch is turned to the
“ON” position, contact your Toyota dealer
to service the vehicle. If the “4WD” warning light flashes...
This indicates that the driveline tempera-
ture has become too high. Without turning
off the engine, do either of the following
to cool the driveline:
Reduce vehicle speed until the light
goes off.
Stop the vehicle at a safe place and
allow the engine to idle until the light
goes off.
If operation of the vehicle is continued
while the light is flashing, the system au-
tomatically shuts off the engine torque that
is applied to the rear wheels to protect
the driveline. If this happens, the light will
flash faster.
When the driveline temperature falls
enough, the light will go off.
If the “4WD” warning light remains on...
This indicates that the system may not
work properly. Contact your Toyota dealer
to service your vehicle.

’08 Rav4_U (L/O 0802)
152
2008 RAV4 from Feb. ’08 Prod. (OM42726U)
The traction control system automatical-
ly helps prevent the spinning of the
front wheels (twowheel drive models)
or 4 wheels (fourwheel drive models)
when the vehicle is started or acceler-
ated on slippery road surfaces.
When the engine switch is turned to the
“ON” position, the system automatically
turns on.
CAUTION
Under certain slippery road condi-
tions, full traction of the vehicle and
power to the front wheels (twowheel
drive models) or 4 wheels (fourwheel
drive models) cannot be maintained,
even though the traction control sys-
tem is in operation. Do not drive the
vehicle under any speed or maneuver-
ing conditions which may cause the
vehicle to lose traction control. If the
road surface is covered with ice or
snow, your vehicle should be fitted
with snow tires or tire chains. Always
drive at a speed that is appropriate
for the present road conditions.
A sound may be heard from the engine
compartment for a few seconds when the
engine is started or just after the vehicle
begins to move. This means that the sys-
tem is in the self−check mode. This sound
does not indicate a malfunction. When the traction control system is oper-
ating, the following conditions occur:
The system controls the spinning of the
front wheels (two
−wheel drive models)
or 4 wheels (four −wheels drive mod-
els). At this time, the slip indicator light
blinks.
The vehicle may vibrate or make a
noise due to brake operation. This indi-
cates the system is functioning proper-
ly.
The slip indicator light comes on for a few
seconds when the engine switch is turned
to the “ON” position. If the indicator light
does not come on when the engine switch
is turned to the “ON” position, contact
your Toyota dealer.
Traction control system

’08 Rav4_U (L/O 0802)
153
2008 RAV4 from Feb. ’08 Prod. (OM42726U)
“VSC” warning light
This light warns that there is a problem
somewhere in the following systems:
Traction control system
“AUTO LSD” system
Enhanced vehicle stability control sys-
tem
Downhill assist control system
Hill −start assist control system
The light will come on when the engine
switch is turned to the “ON” position.
When the systems are work properly, the
light turns off after a few seconds. If the light comes on while driving, all the
above systems will not work. In such a
case, the brakes will operate when applied
(no electronic assistance will be avail-
able), and it will be possible to continue
driving the vehicle.
In the following cases, contact your Toyota
dealer:
The warning light does not come on
when the engine switch is turned to the
“ON” position.
The warning light remains on after the
engine switch is turned to the “ON”
position.
The warning light comes on while driv-
ing.
The “AUTO LSD” system aids traction
by using the traction control system to
control engine performance and braking
when one of the front wheels begins to
spin.
This system is used only when wheel
spinning occurs in a ditch or on a
rough surface.
This system is effective in case one of
the front wheels is spinning.
NOTICE
Do not use the “AUTO LSD” system
in conditions other than the above. A
much greater steering effort and more
careful cornering control will be re-
quired.
“AUTO LSD” system
(twowheel drive models)

’08 Rav4_U (L/O 0802)
154
2008 RAV4 from Feb. ’08 Prod. (OM42726U)
To turn on the system, push the “AUTO
LSD” switch when the vehicle is
stopped.
The “AUTO LSD” indicator light will come
on and remain on while the system is on.
While the system is operating, the slip
indicator light will also flash.
To turn off the system, push the “AUTO
LSD” switch again and the “AUTO LSD”
indicator light will go off.
If the vehicle speed exceeds 50 km/h (31
mph), this system will be cancelled auto-
matically.The “AUTO LSD” indicator light will come
on for a few seconds when the engine
switch is turned to the “ON” position. If
the indicator light does not come on when
the engine switch is turned to the “ON”
position or the “AUTO LSD” switch is
pushed, contact your Toyota dealer.
If the brake actuator temperature becomes
too high, a buzzer will sound for about 3
seconds. (The slip indicator light will also
be lit.) The system will temporarily stop
operating in order to protect the brake
actuator. Although “AUTO LSD” system is
not operating, it is still possible to contin-
ue your driving.
The operation of the system will be auto-
matically restored after the actuator cools
down. After operation is restored, the slip
indicator light will go off.“VSC” warning light
This light warns that there is a problem
somewhere in the following systems:
Traction control system
“AUTO LSD” system
Enhanced vehicle stability control sys-
tem
Downhill assist control system
Hill
−start assist control system
When the engine switch is turned to the
“ON” position, the light will come on.
When the systems are work properly, the
light turns off after a few seconds.