2008 TOYOTA LAND CRUISER warning

163
2−2. Instrument cluster
2
When driving
Indicators and war ning lights
The indicator and warning lights on the instrument cluster and cen
ter panel inform the driver of the
status of the vehicle’s various sys
tems.
Instrument cluster
Center panel
ITY22C017

165
2−2. Instrument cluster
2
When driving
CAUTION
nIf a safety system warning light does not come on
Should a safety system light such as Multi Terrain ABS and the SRS airbag
warning lights not come on when you start the engine, this could mean that
these systems are not available to help protect you in an accident, which
could result in death or serious injury. Have the vehicle inspected by your
Toyota dealer immediately if this occurs.
nWarning lights
Warning lights inform the driver
of malfunctions in the indicated
vehicle’s systems. ( P. 449)
*: These lights turn on when the “ENGINE START STOP” switch is turned
to IGNITION ON mode to indicate that a system check is being per−
formed. They will turn off after the engine is started, or after a few sec−
onds. There may be a malfunction in a system if the lights do not come
on, or if the lights do not turn off. Have the vehicle inspected by your
Toyota dealer.
(if equipped)
*******
***

166
2−2. Instrument cluster
Multi−information display
The Multiinformation di splay presents the driver with a variety of
drivingrelated data.
lTrip information ( P. 167)
Displays driving range, fuel
consumption and other cruis−
ing−related information.
lToyota park assist system
display (
P. 181)
Automatically displayed when
using Toyota park assist sys−
tem.
lCrawl control display
(
P. 197)
Automatically displayed when
using crawl control.
lShift position and shift
range (
P. 153)
l
Warning messages
( P. 460)
Automatically displayed when
a malfunction occurs in one of
the vehicle’s system.

181
2−4. Using other driving systems
2
When driving
Toyota par k assist system (if equipped)
Toyota park assist system uses senso rs in the corners and rear of
the vehicle to detect the distance between the vehicle and any obsta
cles, and informs the driver of th
is distance using the multiinforma
tion display, the touch screen, and warning beeps.
nSensor types
Front corner sensors
Rear corner sensors
Back sensors
nToyota park assist system switch
On/off
To turn the system on, press
the switch. The indicator light
comes on to inform the driver
that the system is operational.
To turn the system off, press
the switch again.

185
2−4. Using other driving systems
2
When driving
Beeps and obstacle distance
A beep sounds when the corner sensors and back sensors are oper−
ating.
lThe beep sounds faster as the vehicle approaches an obstacle.
When the vehicle comes within the following distance of the obsta−
cle, the beep sounds continuously.
Front corner and back sensors: Approximately 1.1 ft. (35 cm)
Rear corner sensors: Approximately 1.0 ft. (30 cm)
lWhen two or more obstacles are detected simultaneously, the
beep system responds to the neare
st obstacle. If one or both come
within the above distances, the bee p will repeat a long tone, fol−
lowed by fast beeps.
l
You can change the volume of the warning beeps. ( P. 187)

186 2−4. Using other driving systems
Obstacle detection range
About 1.8 ft. (60 cm)
About 5.0 ft. (150 cm)
The detection area of the sensors
is shown to the left. If obstacles
move too close to the sensors,
they will not be detected.
The range of the sensors may
change depending on the shape
of the object etc.
Warning beep volume and touch screen settings (vehicles with
navigation system only)
You can change the warning beep volume and touch screen operat−
ing conditions.
Press to display the “Information” screen.
Touch .
ITY24C018
STEP1
STEP 2

187
2−4. Using other driving systems
2
When driving
nChanging the warning beep volume
Touch .
Adjust the beep volume, then touch .
nChanging display and alert settings
Touch .
Touch to change the dist
ance for the back sensors
display and tone indication, then touch .
nDisplay off setting
Touch .
When an obstacle is detected while the rear view monitor is in use, the
warning indicator will appear in the top right of the screen even
has been selected.
nThe Toyota park assist system can be operated when
lFront corner sensors:
The “ENGINE START STOP” switch is in IGNITION ON mode.
The shift lever is in a position other than “P”.
The vehicle speed is less than about 6 mph (10 km/h).
lRear corner and back sensors:
The “ENGINE START STOP” switch is in IGNITION ON mode.
The shift lever is in “R”.
STEP1
STEP 2
STEP 1
STEP 2

193
2−4. Using other driving systems
2
When driving
Shift the four−wheel drive control switch to “L4”, then shift to
“H4” again.
When shifting the four−wheel drive control switch, push the switch
down while turning it.
The low speed four−wheel drive indicator light will flash slowly (turns
on and off every 2 seconds).
Shift the shift lever to “P”.
Shifting to the neutral position is completed with above procedure.
The unengaged “Park” warning light will turn on when the shift lever
is shifted to the “P” position.
To return to “H4” when the vehicle is in this condition, carry out the
following procedure.
nShifting from neutral position to “H4”
Stop the vehicle completely.
Make sure the vehicle is stopped in a safe place while carrying out
the following procedure.
Set the parking brake firmly.
Turn the “ENGINE START STOP” switch to the IGNITION ON
mode.
Do not start the engine at this time.
Depress the brake pedal firmly.
Keep the brake pedal depressed till the end of the procedure.
Shift the shift lever to “N”.
Shift the four−wheel drive control switch to “L4”, and then shift
to “H4” again.
When shifting the four−wheel drive control switch, push the switch
down while turning it.
The low speed four−wheel drive indicator light will turn off.
Shifting to “H4” is completed when the low speed four−wheel drive
indicator light turns off.
STEP9
STEP 10
STEP 1
STEP 2
STEP 3
STEP 4
STEP 5
STEP6