2008 TOYOTA LAND CRUISER warning light

122 1−7. Safety information
CAUTION
nFront passenger occupant classification system precautions
lIf an adult sits in the front passenger seat, the AIR BAG ON indicator light
is illuminated. If the AIR BAG OFF indicator is illuminated, ask the passen−
ger to sit up straight, well back in the seat, feet on the floor, and with the
seat belt worn correctly. If the AIR BAG OFF indicator still remain illumi−
nated, either ask the passenger to move to the second seat, or if that is not
possible, move the front passenger seat fully rearward.
lWhen it is unavoidable to install the forward−facing child restraint system
on the front passenger seat, install the child restraint system on the front
passenger seat in the proper order. (
P. 127)
lDo not modify or remove the front seat.
lDo not kick the front passenger seat or subject it to severe impact. Other−
wise, the SRS warning light may come on to indicate a malfunction in the
detection system. In this case, contact your Toyota dealer immediately.
lDo not use a seat accessory, such as a cushion or seat cover, that covers
the seat cushion surface.
l
Child restraint systems installed on the second seat should not contact the
front seat backs.

163
2−2. Instrument cluster
2
When driving
Indicators and war ning lights
The indicator and warning lights on the instrument cluster and cen
ter panel inform the driver of the
status of the vehicle’s various sys
tems.
Instrument cluster
Center panel
ITY22C017

165
2−2. Instrument cluster
2
When driving
CAUTION
nIf a safety system warning light does not come on
Should a safety system light such as Multi Terrain ABS and the SRS airbag
warning lights not come on when you start the engine, this could mean that
these systems are not available to help protect you in an accident, which
could result in death or serious injury. Have the vehicle inspected by your
Toyota dealer immediately if this occurs.
nWarning lights
Warning lights inform the driver
of malfunctions in the indicated
vehicle’s systems. ( P. 449)
*: These lights turn on when the “ENGINE START STOP” switch is turned
to IGNITION ON mode to indicate that a system check is being per−
formed. They will turn off after the engine is started, or after a few sec−
onds. There may be a malfunction in a system if the lights do not come
on, or if the lights do not turn off. Have the vehicle inspected by your
Toyota dealer.
(if equipped)
*******
***

181
2−4. Using other driving systems
2
When driving
Toyota par k assist system (if equipped)
Toyota park assist system uses senso rs in the corners and rear of
the vehicle to detect the distance between the vehicle and any obsta
cles, and informs the driver of th
is distance using the multiinforma
tion display, the touch screen, and warning beeps.
nSensor types
Front corner sensors
Rear corner sensors
Back sensors
nToyota park assist system switch
On/off
To turn the system on, press
the switch. The indicator light
comes on to inform the driver
that the system is operational.
To turn the system off, press
the switch again.

193
2−4. Using other driving systems
2
When driving
Shift the four−wheel drive control switch to “L4”, then shift to
“H4” again.
When shifting the four−wheel drive control switch, push the switch
down while turning it.
The low speed four−wheel drive indicator light will flash slowly (turns
on and off every 2 seconds).
Shift the shift lever to “P”.
Shifting to the neutral position is completed with above procedure.
The unengaged “Park” warning light will turn on when the shift lever
is shifted to the “P” position.
To return to “H4” when the vehicle is in this condition, carry out the
following procedure.
nShifting from neutral position to “H4”
Stop the vehicle completely.
Make sure the vehicle is stopped in a safe place while carrying out
the following procedure.
Set the parking brake firmly.
Turn the “ENGINE START STOP” switch to the IGNITION ON
mode.
Do not start the engine at this time.
Depress the brake pedal firmly.
Keep the brake pedal depressed till the end of the procedure.
Shift the shift lever to “N”.
Shift the four−wheel drive control switch to “L4”, and then shift
to “H4” again.
When shifting the four−wheel drive control switch, push the switch
down while turning it.
The low speed four−wheel drive indicator light will turn off.
Shifting to “H4” is completed when the low speed four−wheel drive
indicator light turns off.
STEP9
STEP 10
STEP 1
STEP 2
STEP 3
STEP 4
STEP 5
STEP6

207
2−4. Using other driving systems
2
When driving
CAUTION
nWhen the VSC is activated
The slip indicator light flashes and a warning buzzer sounds. Always drive
carefully.
Reckless driving may cause an accident. Exercise particular care when the
indicator light flashes and a buzzer sounds.
nReplacing tires
Make sure that all tires are of the
same size, brand, tread pattern and total
load capacity. In addition, make sure that the tires are inflated to the speci−
fied tire pressure level.
The Multi Terrain ABS and VSC will not function correctly if different tires are
fitted on the vehicle.
Contact your Toyota dealer for further information when replacing tires or
wheels.
NOTICE
nKDSS
In the following situations, there is the possibility that a system malfunction
has occurred, and drive comfort and the vehicle’s ability to travel on poor
road surfaces may be reduced. Take the vehicle to your Toyota dealer imme−
diately.
lWhen turning a corner, the vehicle’s body seems to roll further than nor−
mal.
l
If after the vehicle has been left in a slanted position for a long time, for
example with the wheels of one side parked on a curb, the vehicle does
not return to level when driving (the vehicle remains slanted to one side
after returning the vehicle to level ground).

394 4−3. Do−it−yourself maintenance
Press and hold the tire pressure
warning reset switch until the tire
pressure warning light blinks
slowly three times and the mes−
sage “TIRE PRESSURE RESET
PROCEEDING” appears on the
multi−information display.
Wait for a few minutes with the IGNITION ON mode, and then
turn the “ENGINE START STOP” switch to OFF mode.
STEP4
STEP 5

395
4−3. Do−it−yourself maintenance
4
Maintenance and care
Registering ID codes
The tire pressure warning valve and transmitter is equipped with a
unique ID code. When replacing a tire pressure warning valve and
transmitter, it is necessary to regi ster the ID code of tire pressure
warning valve and transmitter. Have the ID code registered by your
Toyota dealer.
n When to replace your vehicle’s tires
Tires should be replaced if:
lYou have tire damage such as cuts, splits, cracks deep enough to
expose the fabric or bulges indicating internal damage
lA tire goes flat repeatedly or c annot be properly repaired due to the
size or location of a cut or other damage
If you are not sure, consult with your Toyota dealer.
n Replacing tires and wheels
If the ID code of the tire pressure warning valve and transmitter is not
registered, the tire pre ssure warning system will not work properly. After
driving for about 20 minutes, the ti
re pressure warning light comes on
after blinking for 1 minute to indicate a system malfunction.
n Tire life
Any tire over 6 years old must be checked by a qualified technician even
if they have seldom or never been used or damage is not obvious.
n If the treadwears down below 0.16 in. (4 mm) on snow tires
The effectiveness of snow tires is lost.