2008 TOYOTA LAND CRUISER brake light

193
2−4. Using other driving systems
2
When driving
Shift the four−wheel drive control switch to “L4”, then shift to
“H4” again.
When shifting the four−wheel drive control switch, push the switch
down while turning it.
The low speed four−wheel drive indicator light will flash slowly (turns
on and off every 2 seconds).
Shift the shift lever to “P”.
Shifting to the neutral position is completed with above procedure.
The unengaged “Park” warning light will turn on when the shift lever
is shifted to the “P” position.
To return to “H4” when the vehicle is in this condition, carry out the
following procedure.
nShifting from neutral position to “H4”
Stop the vehicle completely.
Make sure the vehicle is stopped in a safe place while carrying out
the following procedure.
Set the parking brake firmly.
Turn the “ENGINE START STOP” switch to the IGNITION ON
mode.
Do not start the engine at this time.
Depress the brake pedal firmly.
Keep the brake pedal depressed till the end of the procedure.
Shift the shift lever to “N”.
Shift the four−wheel drive control switch to “L4”, and then shift
to “H4” again.
When shifting the four−wheel drive control switch, push the switch
down while turning it.
The low speed four−wheel drive indicator light will turn off.
Shifting to “H4” is completed when the low speed four−wheel drive
indicator light turns off.
STEP9
STEP 10
STEP 1
STEP 2
STEP 3
STEP 4
STEP 5
STEP6

194 2−4. Using other driving systems
nThe fourwheel drive control switch can be operated when
lThe “ENGINE START STOP” switch is in IGNITION ON mode.
lThe shift lever is in the “N” position.
lThe vehicle is stopped completely.
nAdvice for driving on slippery roads in “L4” (low speed position)
lIf you shift the four−wheel drive control switch to “L4” and the shift lever to
the “2” range of “S” while driving in steep off−road areas, the output of the
brake can be controlled effectively by the active traction control system,
which assists the driver to control the driving power of 4 wheels.
lUse the “1” range of “S” of the shift lever for maximum power and traction
when your wheels get stuck or when driving down a steep incline. In the
following cases, the output of the brake can be controlled by the active
traction control system if the engine speed is under 3,000 rpm (normally
under 3,000 rpm when the wheels get unstuck).
The four−wheel drive control switch is in the “L4” position and the shift
lever is in the “1” range of “S” or the shift lever is in “D” or “S” with the
transmission downshifted to first gear.
The four−wheel drive control switch is in the “L4” position and the shift
lever is in the “R” position.
nThe center differential lock/unlock button can be operated when
lThe “ENGINE START STOP” switch is in IGNITION ON mode.
lThe vehicle speed is less than 60 mph (100 km/h).
nLocking/unlocking the center differential
lWhen the center differential is locked, VSC (vehicle stability control) is
automatically turned off. (The center di
fferential lock and “VSC OFF” indi−
cator lights come on.)
lIf the operation is not completed, the center differential lock indicator
blinks. If the indicator light does not turn off when unlocking the center
differential, drive straight ahead while accelerating or decelerating, or
drive in reverse.
lIf the center differential lock/unlock is not completed within 5 seconds
while the cruise control system is on, cancel the cruise control system.

195
2−4. Using other driving systems
2
When driving
nIf the low speed fourwheel drive in dicator light or the center differen
tial lock indicator light blinks
lIf the low speed four−wheel drive indicator light continues to blink when
using the four−wheel drive control switch, stop the vehicle completely,
move the shift lever to “N” and operate the switch again.
lIf the shift lever is moved before the low speed four−wheel drive indicator
light has turned on/off, a beep sounds and the transfer position may not
successfully change. In this case, stop the vehicle completely, return the
shift lever to “N” and operate the switch again.
lIf the engine coolant temperature is too low, the four−wheel drive control
system may not be able to shift. When the engine is warmer press the
switch again.
If the low speed four−wheel drive indicator light or the center differential lock
indicator light continues to blink even after attempting the above, there may
be a malfunction in the engine, the brake system or the four−wheel drive sys−
tem. In this case, you may not be able to shift between “H4” and “L4”, and
the center differential lock may not be operable. Have the vehicle inspected
by your Toyota dealer immediately.

205
2−4. Using other driving systems
2
When driving
nSounds and vibrations caused by the Multi Terrain ABS, brake assist,
Active TRAC, VSC and hillstart assist control
lA sound may be heard from the engine compartment when the engine is
started or just after the vehicle begins to move. This sound does not indi−
cate that a malfunction has occurred in any of these systems.
lAny of the following conditions may occur when the above systems are
operating. None of these indicates that a malfunction has occurred.
Vibrations may be felt through the vehicle body and steering.
A motor sound may be heard after the vehicle comes to a stop.
The brake pedal may pulsate slightly after the Multi Terrain ABS is acti−
vated.
The brake pedal may move down slightly after the Multi Terrain ABS is
activated.
nHillstart assist control is operational when
lThe shift lever is in “D” or “S”.
l
The brake pedal is not depressed.

238 2−5. Driving information
CAUTION
nHitches
lLubricate the hitch ball with a light coat of grease.
lIf using a weight distributing hitch when towing, keep your vehicle level
with the ground.
nWhen towing a trailer
lIf the gross trailer weight exceeds 1000 lb. (453 kg), trailer brakes are
required. Toyota recommends trailers with brakes that conform to all appli−
cable federal and state/provincial regulations.
lNever tap into your vehicle’s hydraulic system, as this will lower the vehi−
cle’s braking effectiveness.
lNever tow a trailer without using a safety chain securely attached to both
the trailer and the vehicle. If damage occurs to the coupling unit or hitch
ball, there is danger of the trailer wandering into another lane.
NOTICE
nWhen installing a trailer hitch
lUse only the position recommended by your Toyota dealer. Do not install
the trailer hitch on the bumper; this may cause body damage.
lDo not use axle−mounted hitches, as they can cause damage to the axle
housing, wheel bearings, wheels or tires.
nSafety chain
A safety chain must always be used between the towing vehicle and the
trailer. Leave sufficient slack in the chain for turns. The chain should cross
under the trailer tongue to prevent the tongue from dropping to the ground in
the case that it becomes damaged or separated. For the correct safety chain
installation procedure, ask your Toyota dealer.
nDo not directly splice trailer lights
Directly splicing trailer lights may damage your vehicle’s electrical system
and cause a malfunction.

368 4−2. Maintenance
Vehicle interior
Items Check points
Accelerator pedalMoves smoothly (without uneven
pedal effort or catching)?
Automatic transmission “Park”
mechanismCan the vehicle be hold securely
on an incline with the shift lever in
“P”?
Brake pedalMoves smoothly?
Does it have appropriate clear−
ance and correct amount of free
play?
BrakesPulls to one side when applied?
Loss of brake effectiveness?
Spongy feeling brake pedal?
Pedal almost touches floor?
Head restraintsMove smoothly and lock
securely?
Indicators/buzzersFunction properly?
LightsDo all the lights come on?
Headlights aimed correctly?
Parking brakeMoves smoothly?
Can hold the vehicle securely on
an incline?
Seat beltsDoes the seat belt system oper−
ate smoothly?
Are the belts undamaged?
SeatsDo the seat controls operate
properly?
Steering wheel
Moves smoothly?
Has correct free play?
No strange noises?

385
4−3. Do−it−yourself maintenance
4
Maintenance and care
nBrake fluid can absorb moisture from the air
Excess moisture in the fluid can cause a dangerous loss of braking effi−
ciency. Use only newly opened brake fluid.
CAUTION
nWhen filling the reservoir
Take care because brake fluid can harm your hands or eyes and damage
painted surfaces.
If fluid gets in your eyes, flush your eyes with clean water immediately.
If you still experience discomfort, see a doctor.
NOTICE
nIf the fluid level is low or high
It is normal for the brake fluid level to go down slightly as the brake pads
wear or when the fluid level in the accumulator is high.
If the reservoir needs frequent refilling, it may indicate a serious problem.

388 4−3. Do−it−yourself maintenance
nChecking battery condition
Check the battery condition using the indicator color.
Good condition
Charging is necessary.
Have the vehicle inspected by
your Toyota dealer.
Not working properly, have the
battery checked by your Toy−
ota dealer.
ITY43C100
Green
Dark
Clear or light yellow
Type A
Blue
White
Red
Type B
nBefore recharging
When recharging, the battery produces hydrogen gas which is flammable
and explosive. Therefore, before recharging:
lIf recharging with the battery installed on the vehicle, be sure to discon−
nect the ground cable.
lMake sure the power switch on the charger is off when connecting and
disconnecting the charger cables to the battery.
nAfter recharging the battery
The engine may not start. Follow the procedure below to initialize the sys−
tem.
1. Depress the brake pedal with the shift lever in “N”.
2. Open and close any of the doors.
3. Restart the engine.