2008 TOYOTA FJ CRUISER torque

47
1−3. Adjustable components (seats, mirrors, steering wheel)
1
Before driving
 If you cannot raise the seatback
 When the bottom cushion is reinstalled
 Waterproof and waterrepellent seats
Waterproof and water−repellent seats are installed in your vehicle: however,
the water−repellent effect does not last forever.Release the seat belt lock by:
Pushing on the lower front edge of the
seatback to slacken the seat belt.
Let the seat belt retract a little.
Click the claw of the hinge into the hole of
the bottom cushion before refastening the
dial.
Firmly tighten the hexagon head bolts
using a torque wrench.
Tightening torque:
12.5 ft⋅lbf (17 N⋅m, 1.7 kgf⋅m)

48 1−3. Adjustable components (seats, mirrors, steering wheel)
CAUTION
 When the seatback is folded
Do not sit on or place anything on the seatback while driving.
When returning the seats to their original position
Observe the following precautions. Failure to do so may result in death or
serious injury.
Be careful not to get your hands or feet pinched in the seat.
Make sure the seatbacks and bottom cushions are securely locked. Fail−
ure to do so will prevent the
seat belt from operating properly.
 Check that the seat belts are not twisted or caught under the seat.
Arrange the seat belts in the proper positions for ready use.
When removing or reinstalling the bottom cushion
Observe the following precautions. Failure to do so may result in death or
serious injury.
Do not get in the vehicle with the bottom cushions uninstalled.
Do not leave the removed bottom cushion unsecured in the vehicle.
Do not try to sit on or place anything on the removed bottom cushion.
Do not drop the bottom cushion.

Have the hexagon head bolts tightened with a torque wrench to 12.5 ft⋅lbf
(17 N⋅m, 1.7 kgf⋅m), or have them tightened by your Toyota dealer.
Failure to do so may cause the dials to be loosened and the bottom cush−
ions to be removed.
NOTICE
 Before folding down or removing the seats
 The seat belts buckles must be stowed.

The head restraints must be removed before you fold down the seatback.

346 5−2. Steps to take in an emergency
Lower the vehicle.
Firmly tighten each nut two or
three times in the order shown in
the illustration.
Tightening torque:
85 ft⋅lbf (113 N⋅m, 11.5 kgf⋅m)
Reinstall the wheel ornament.
Aluminum wheel

5
When trouble arises
347 5−2. Steps to take in an emergency
Steel wheel
Stowing the flat tire, jack and all tools
Install the flat tire in the reverse order of removal.
Tightening torque:
65 ft⋅lbf (88 N⋅m, 8.9 kgf⋅m)
Stow the tools and jack securely.
CAUTION
Using the jack
Improper use of the jack may lead to death or injuries due to the vehicle
suddenly falling off the jack.
Do not use the jack for any purpose other than replacing tires or install−
ing and removing tire chains.
Only use the jack that comes with this vehicle for replacing a flat tire.
Do not use it on other vehicles, an d do not use other jacks for replac−
ing tires on this vehicle.
Always check that the jack is securely set to the jack point.
Do not put any part of your body under the vehicle supported by a jack.
Do not start or run the engine while your vehicle is supported by the
jack.
Do not raise the vehicle while someone is in it.
When raising the vehicle, do not put an object on or under the jack.
Do not raise the vehicle to a hei
ght greater than that required to
replace the tire.

348 5−2. Steps to take in an emergency
CAUTION
Using the jack
Use a jack stand if it is necessary to get under the vehicle.
Take particular care when lowering the vehicle to ensure that no one
working on or near the vehicle will be injured.
Using the jack handle
Tighten all the square head bolts securely to prevent the extension parts
from coming apart unexpectedly.
Replacing a flat tire
Observe the following precautions to reduce the risk of injury.
Do not try to remove the wheel ornament by hand. Take due care in
handling the ornament to avoid unexpected personal injury.
Never use oil or grease on the wheel bolts or wheel nuts.
The oil or grease can cause the wheel nuts to loosen, causing a seri−
ous accident. Remove any oil or grease on the wheel bolts or wheel
nuts.
Have the wheel nuts tightened with a torque wrench to 85 ft⋅lbf (113
N⋅m, 11.5 kgf⋅m) as soon as possible after changing wheels.
Failure to follow these precautions could cause the nuts to loosen and
the wheels may fall off, which could lead to an accident causing death
or serious injury.
Do not attach a heavily damaged wheel ornament, as it may fly off the
wheel while the vehicle is moving.

370 6−1. Specifications
Tires and wheels
Tire size P265/75R16 114T, P265/70R17 113S
Tire inflation pressure
(Recommended cold tire
inflation pressure)Front tires:
32 psi (220 kPa, 2.2 kgf/cm
2 or bar)
Rear tires:
32 psi (220 kPa, 2.2 kgf/cm
2 or bar)
Spare tire:
32 psi (220 kPa, 2.2 kgf/cm
2 or bar)
Wheel size 16 7 J, 17
7 1/2 J
Wheel nut torque 85 ft⋅lbf (113 N⋅m, 11.5 kgf⋅m)