2008 TOYOTA FJ CRUISER automatic transmission

114
2−1. Driving procedures
Engine (ignition) switch
 Engine switch
LOCK
The steering wheel is locked
and the key can be removed.
ACC
Some electrical components
such as the audio system can
be used.
ON
All electrical components can
be used.
START
For starting the engine.
 Starting the engine
Automatic transmission
Check that the parking brake is set.
Check that the shift lever is set in P.
Sit in the driver ’s seat and firmly depress the brake pedal.
Turn the engine switch to the START position and start the
engine.
Manual transmission
Check that the parking brake is set.
Check that the shift lever is set in N.
Firmly depress the brake pedal and clutch pedal.
Turn the engine switch to the START position and start the
engine.

117
2−1. Driving procedures
2
When driving
Automatic Transmission (if equipped)
Select a shift position appropriate for the driving conditions.
 Shifting the shift lever
While the engine switch is on, depress the brake pedal and
move the shift lever.
 Shift position uses
*: To improve fuel consumption and reduce noises, set the shift lever in
D for normal driving.
Shift positionFunction
PParking the vehicle or starting the engine
RReversing
NNeutral
DNormal driving*
4Position for engine braking
3, 2Position for more powerful engine braking
LPosition for maximum engine braking

128 2−2. Instrument cluster
 Indicators
The indicators inform the driver of the operating state of the
vehicle’s various systems.
Turn signal indicator
(
P. 121)(if equipped)
Active traction control
system indicator (
P.
148)
Headlight high beam
indicator (
P. 131)
*
(if equipped)
AUTO LSD indicator
(
P. 150)
Security indicator
(
P. 68)(if equipped)
Four−wheel drive
indicator(
P. 146)
(Automatic
transmission
vehicles)
Shift position and shift
range indicators
(
P. 117)
(if equipped)
Center differential lock
indicator (
P. 144)
(if equipped)
Rear differential lock
indicator (
P. 152)
(if equipped)
Cruise control indicator
(
P. 136)
*AIR BAG ON indicator
(
P. 85)
*Slip indicator
(
P. 148, 150, 156)
*AIR BAG OFF indicator
(
P. 85)
*VSC OFF indicator
(
P. 157)

129
2−2. Instrument cluster
2
When driving
CAUTION
 If a safety system warning light does not come on
Should a safety system light such as ABS and the SRS airbag warning light
not come on when you start the engine, this could mean that these systems
are not available to help protect you in an accident, which could result in
death or serious injury. Have the vehicle inspected by your Toyota dealer
immediately if this occurs.
 Warning lights
Warning lights inform the driver of malfunctions in any of the
vehicle’s systems. ( P. 331)
*: These lights turn on when the engine switch is turned to the ON
position to indicate that a system check is being performed. They will
turn off after the engine is started, or after a few seconds. There may
be a malfunction in a system if a light does not come on, or if the
lights do not turn off. Have the vehicle inspected by your Toyota
dealer.
(Canada)(U.S.A.)
(U.S.A.)(Automatic
transmission
vehicles)
(if equipped)
********
**

137
2−4. Using other driving systems
2
When driving
 Cruise control can be set when
 The shift lever is in D or 4 (vehicles with an automatic transmission).
Vehicle speed is between approximately 25 mph (40 km/h) and 125 mph
(200 km/h).
 Accelerating
The vehicle can be accelerated normally.
Automatic cruise control cancelation
The set speed is automatically cancelled in any of the following situations.
Actual vehicle speed falls more than 10 mph (16 km/h) below the preset
vehicle speed.
At this time, the memorized set speed is not retained.
 Actual vehicle speed is below 25 mph (40 km/h).

VSC is activated.
 Canceling and resuming regular acceleration
Cancel
Pull the lever towards you to
cancel cruise control.
The speed setting is also can−
celed when the brakes are
applied or the clutch
depressed (manual transmis−
sion).
Resume
To resume cruise control and
return to the set speed, push
the lever up.

146
2−4. Using other driving systems
Four−wheel drive system (4WD models with an automatic transmission)
Use the frontwheel drive control le ver to select the following trans
fer modes.
The four−wheel drive indicator comes on when the H4, N or L4 mode is
selected.
H2 (high speed position, two−wheel drive)
Normal driving.
H4 (high speed position, four−wheel drive)
Greater traction than two wheel drive.
When you experience a loss of power, such as wheel slipping.
N (neutral position)
No power is delivered to the wheels.
L4 (low speed position, four−wheel drive)
Driving requiring maximum power and traction such as climbing or
descending steep hills, off−road driving and hard pulling in sand or mud,
etc.

148
2−4. Using other driving systems
Active traction control system (if equipped)
When the active traction control system is operating
If all wheels spin, the slip indica−
tor flashes to indicate that the
active traction control system
have been engaged.
The active traction control system automatically helps prevent the
spinning of 4 wheels when the veh icle is started or accelerated on
slippery road surfaces.
 System operation
Vehicles with an automatic transmission:
Shift the front−wheel drive control lever into L4.
Vehicles with a manual transmission:
Shift the four−wheel drive control lever into LL.
Press the A−TRAC switch to
activate the system.
At this time, the active traction
control system indicator will
come on.
To cancel the system, push the
switch again.

152
2−4. Using other driving systems
Rear differential lock system (if equipped)
Using the rear differential lock system
Automatic transmission
4WD models: Before using the rear differential lock system.
Shift the front−wheel drive control
lever into L4 to see if this is
sufficient. If this has no effect, additionally use the rear differ−
ential lock system.
Be sure to stop the wheels.
Press the RR DIFF LOCK switch.
After the rear differential is locked, the indicator will come on.
Gently depress the accelerator pedal.
Unlock the rear differential as soon as the vehicle moves out.
To unlock the rear differential, push the switch again. The rear differential lock system is provided for use only when wheel
spinning occurs in a ditch or
on a slippery or ragged surface.
The rear differential lock system is effective in case one of the rear
wheels is spinning.
Press the RR DIFF LOCK
switch to lock the rear differen−
tial.
At this time, the indicator will
blink. Wait a few seconds for
the system to complete opera−
tion. After the rear differential is
locked, the rear differential lock
indicator will stop blinking and
remain on.
To unlock the rear differential,
push the switch again.