2008 TOYOTA AVALON navigation system

BASIC FUNCTIONS
59
When your vehicle is not receiving signals
from the satellites, the “GPS” mark does
not appear at the screen.
The GPS signal may be physically ob-
structed, leading to inaccurate vehicle
position on the map display. Tunnels, tall
buildings, trucks, or even the placement of
objects on the instrument panel may ob-
struct the GPS signals.
The GPS satellites may not send signals
due to repairs or improvements being
made to them.
Even when the navigation system is re-
ceiving good GPS signals, the vehicle
position may not be shown accurately or
inappropriate route guidance may occur in
some cases.
NOTICE
The installation of window tinting
may obstruct the GPS signals. Most
window tinting contains some metal-
lic content that will interfere with GPS
signal reception of the antenna in the
instrument panel. We advise against
the use of window tinting on vehicles
equipped with navigation systems.
(a) Accurate current vehicle position
may not be shown in the following
cases:
When driving on a small angled Y−
shaped road.
When driving on a spiral road.
When driving on a slippery road such
as in sand, gravel, snow, etc.
When driving on a long straight road.
When freeway and surface streets run
in parallel.
After moving by ferry or vehicle carrier.
When a long route is searched during
high speed driving.
When driving without setting the cur-
rent position calibration correctly.
After repeating a change of directions
by going forward and backward, or
turning on a turntable in the parking lot.
When leaving a covered parking lot or
parking garage.
When a roof carrier is installed.
When driving with the tire chains
installed.
When the tires are worn.
After replacing a tire or tires.
When using tires that are smaller or
larger than the factory specifications.
When the tire pressure in any of the
four tires is not correct.
INFORMATION
If your vehicle cannot receive GPS
signals, you can correct the current
position manually. For the informa-
tion on setting the current position
calibration, see page 95.

BASIC FUNCTIONS
60
(b) Inappropriate route guidance may
occur in the following cases:
When turning at a wrong intersection
off the designated route guidance.
If you are heading for a destination
without passing through a set preferred
road, automatic rerouting may display
a route returning to the set preferred
road.
When turning at an intersection for
which there is no route guidance.
When passing through an intersection
for which there is no route guidance.
During automatic rerouting, the route
guidance may not be available for the
next turn to the right or left.
It may take a long time to operate auto-
matic rerouting during high speed dri-
ving. In automatic rerouting, a detour
route may be shown.
During automatic rerouting, the route
may not be changed.
The route in a U−turn may be shown or
announced.
A location may have multiple names
and the system will announce one or
more.
Some routes may not be searched.
If the route to your destination includes
gravel, unpaved roads or alleys, the
route guidance may not be shown.
Your destination point might be shown
on the opposite side of the street.
When a portion of the route has regula-
tions prohibiting the entry of the vehicle
that vary by time or season or other
reasons.
The road and map data stored in your
navigation system may not be com-
plete or may not be the latest release.After replacing the tire, implement the
operation described in the “Current
position calibration”. (For details, see
page 95.)
This navigation system uses tire turning
data and is designed to work with factory−
specified tires for your Toyota. Installing
tires that are larger or smaller than the orig-
inally equipped diameter may cause inac-
curate display of the vehicle’s position.
The tire pressure also affects the diameter
of the tires so please make sure the tire
pressure of all four tires is correct.

BASIC FUNCTIONS
62
ENDUSER TERMS
The data (“Data”) is provided for
your personal, internal use only
and not for resale. It is
protected by copyright, and is
subject to the following terms
and conditions which are agreed
to by you, on the one hand, and
DENSO CORPORATION
(“[CLIENT]”) and its licensors
(including their licensors and
suppliers) on the other hand.
©2005 NAVTEQ. All rights re-
served.
The Data for areas of Canada
includes information taken with
permission from Canadian author-
ities, including: ©Her Majesty the
Queen in Right of Canada,
©Queen’s Printer for Ontario,
©Canada Post Corporation, Geo-
Base.
TERMS AND CONDITIONS
Personal Use Only. You agree
to use this Data together with the
navigation system for the solely
personal, non−commercial pur-
poses for which you were li-
censed, and not for service bu-
reau, time−sharing or other simi-
lar purposes. Accordingly, but
subject to the restrictions set
forth in the following paragraphs,
you may copy this Data only as
necessary for your personal use
to (i) view it, and (ii) save it,
provided that you do not remove
any copyright notices that appear
and do not modify the Data in
any way. You agree not to
otherwise reproduce, copy,
modify, decompile, disassemble
or reverse engineer any portion
of this Data, and may not trans-
fer or distribute it in any form, for
any purpose, except to the extent
permitted by mandatory laws.
Data provided in multi−disc sets
may not be transferred or sold
on a divided or single disc basis.

BASIC FUNCTIONS
63
Restrictions. Except where you
have been specifically licensed to
do so by [CLIENT], and without
limiting the preceding paragraph,
you may not (a) use this Data
with any products, systems, or
applications installed or otherwise
connected to or in communication
with vehicles, capable of vehicle
navigation, positioning, dispatch,
real time route guidance, fleet
management or similar applica-
tions; or (b) with or in commu-
nication with any positioning de-
vices or any mobile or wireless−
connected electronic or computer
devices, including without limita-
tion cellular phones, palmtop and
handheld computers, pagers, and
personal digital assistants or
PDAs.
Warning
. The Data may contain
inaccurate or incomplete informa-
tion due to the passage of time,
changing circumstances, sources
used and the nature of collecting
comprehensive geographic data,
any of which may lead to incor-
rect results.
No Warranty.
This Data is pro-
vided to you “as is,” and you
agree to use it at your own risk.
[CLIENT] and its licensors (and
their licensors and suppliers)
make no guarantees, representa-
tions or warranties of any kind,
express or implied, arising by law
or otherwise, including but not
limited to, content, quality, accu-
racy, completeness, effective-
ness, reliability, fitness for a par-
ticular purpose, usefulness, use
or results to be obtained from
this Data, or that the Data or
server will be uninterrupted or er-
ror−free.
Disclaimer of Warranty: [CLIENT]
AND ITS LICENSORS (INCLUD-
ING THEIR LICENSORS AND
SUPPLIERS) DISCLAIM ANY
WARRANTIES, EXPRESS OR
IMPLIED, OF QUALITY, PER-
FORMANCE, MERCHANTABIL-
ITY, FITNESS FOR A PARTICU-
LAR PURPOSE OR NON−IN-
FRINGEMENT. Some States,
Territories and Countries do not
allow certain warranty exclusions,
so to that extent the above ex-
clusion may not apply to you.
Disclaimer of Liability:
[CLIENT]
AND ITS LICENSORS (INCLUD-
ING THEIR LICENSORS AND
SUPPLIERS) SHALL NOT BE LI-
ABLE TO YOU IN RESPECT OF
ANY CLAIM, DEMAND OR AC-
TION, IRRESPECTIVE OF THE
NATURE OF THE CAUSE OF
THE CLAIM, DEMAND OR AC-
TION ALLEGING ANY LOSS, IN-
JURY OR DAMAGES, DIRECT
OR INDIRECT, WHICH MAY RE-
SULT FROM THE USE OR POS-
SESSION OF THE INFORMA-
TION; OR FOR ANY LOSS OF
PROFIT, REVENUE, CON-
TRACTS OR SAVINGS, OR ANY
OTHER DIRECT, INDIRECT, INCI-
DENTAL, SPECIAL OR CONSE-
QUENTIAL DAMAGES ARISING
OUT OF YOUR USE OF OR IN-
ABILITY TO USE THIS IN-
FORMATION, ANY DEFECT IN
THE INFORMATION, OR THE
BREACH OF THESE TERMS OR
CONDITIONS, WHETHER IN AN
ACTION IN CONTRACT OR
TORT OR BASED ON A WAR-
RANTY, EVEN IF [CLIENT] OR
ITS LICENSORS HAVE BEEN
ADVISED OF THE POSSIBILITY
OF SUCH DAMAGES.

BASIC FUNCTIONS
66
LIMITED RIGHTS NOTICE
(JUN 1987)
These data are submitted with
limited rights under Government
Contract No. _____ (and sub-
contract ______, if appropriate).
These data may be reproduced
and used by the Government
with the express limitation that
they will not, without written per-
mission of the Contractor, be
used for purposes of manufac-
ture nor disclosed outside the
Government; except that the
Government may disclose these
data outside the Government for
the following purposes, if any,
provided that the Government
makes such disclosure subject
to prohibition against further use
and disclosure: There are no
additional purposes permitting
disclosure of such Data.
The manufacturer/supplier of the
Data is NAVTEQ, 222 Merchan-
dise Mart Plaza, Suite 900, Chi-
cago, Illinois 60654.If the Contracting Officer refuses
to use either of the licenses pro-
vided in (i) or (ii), herein, the
Contracting Officer must notify
NAVTEQ North America, LLC
prior to seeking additional or al-
ternative rights in the NAVTEQ
Data.
END USER LICENSE AGREE-
MENT
PLEASE READ THIS AGREE-
MENT CAREFULLY BEFORE US-
ING THE NAVIGATION SYSTEM
THIS IS A LICENSE AGREE-
MENT FOR YOUR COPY OF
THE SPATIAL MAP DATABASE,
INCLUDING LOCATION CODES
AND RELATED PRODUCTS
(COLLECTIVELY, THE “DATA-
BASE”), USED IN THE NAVIGA-
TION SYSTEM. BY USING THE
NAVIGATION SYSTEM AND THE
DATABASE, YOU ACCEPT AND
AGREE TO BE BOUND BY ALL
TERMS AND CONDITIONS SET
FORTH BELOW.
LICENSE GRANT
Denso Corporation (“Denso”), as
a licensed distributor of the DA-
TABASE, grants to you a non−ex-
clusive, non−perpetual license to
use your copy of the DATABASE
for your personal use or for your
use in your business’ internal op-
erations and not for any other
purpose. This license does not
include the right to grant sub−li-
censes.

BASIC FUNCTIONS
70
END USER NOTICE
PLEASE READ THIS NOTICE
CAREFULLY BEFORE USING
THIS NAVIGATION SYSTEM
The Point Of Interest Data
(“POI” Data) in the navigation
system is in part provided by
infoUSA Inc. (“infoUSA”). By
using the POI Data, you accept
and agree to all terms and con-
ditions set forth below.
1. OWNERSHIP
All rights, title and interest to the
infoUSA POI Data shall be re-
tained by infoUSA.
2. LIMITATIONS ON USE
Except to the extent explicitly
permitted by mandatory laws, you
may not extract or reutilize any
portion of the contents of the
POI Data, nor reproduce, copy,
modify, adapt, translate, disas-
semble, decompile, or reverse
engineer any portion of the POI
Data.3. TRANSFER
You may not transfer the POI
Data to third parties, except to-
gether with the system for which
it was created, provided that you
do not retain any copy of the
POI Data.
4. DISCLAIMER OF WARRANTY
EXCEPT AS STATED HEREIN,
INFOUSA MAKES NO EXPRESS
OR IMPLIED WARRANTIES, IN-
CLUDING, WITHOUT LIMITA-
TION, ANY EXPRESS OR IM-
PLIED WARRANTY OF FITNESS
FOR A PARTICULAR PURPOSE
OR WARRANTY OF MERCHANT-
ABILITY.
5. LIMITATION OF LIABILITY
EITHER INFOUSA OR SUPPLI-
ER OF POI DATA SHALL NOT
BE LIABLE FOR ANY INDIRECT,
CONSEQUENTIAL OR INCIDEN-
TAL DAMAGES MADE OR AL-
LEGED IN CONNECTION WITH
YOUR USE OF THE POI DATA.

ADVANCED FUNCTIONS
94
CHANGING THE NAME
Select alphabet or numeral keys to in-
put the name.
After you finish your entry, select the
“OK” switch on the screen.
The previous screen will be displayed.
CHANGING THE LOCATION
Move the cursor to your desired point,
and push the “ENTER” button of the
navigation controller.
CHANGING THE AREA SIZE
Select one of the “detour gauge” on the left
side of this screen if you want to change
the area size.(c) Deleting area to avoid
1. Select the
“Delete” switch of the
“Area to avoid” to display the “Delete
area to avoid” screen.
2. Select the area you want to delete
from the list.
“Delete all”: All registered areas to avoid
in the system are deleted.
3. Messages appear depending on the
type of deletion. If you want to delete,
select the
“Yes” switch. To cancel the
deletion, select the “No” switch.

ADVANCED FUNCTIONS
95
The current vehicle position mark will
be automatically corrected while driv-
ing on reception of GPS signals. If your
vehicle cannot receive GPS signals,
you can correct the current position
mark manually.
1. Push the “MENU” button on the
navigation controller.
2. Select the “Setup” switch.
3. Select the “Calib.” switch on the
right side of the screen.
The next screen appears.
4. Select the “Position/Direction”switch.
INFORMATION
For additional information on current
position accuracy, see “Limitations
of the navigation system” on page 58.
Current position calibration