2008 SUZUKI GRAND VITARA engine overheat

Downloaded from www.Manualslib.com manuals search engine OPERATING YOUR VEHICLE
A. WARNING
Do not "ride" the brakes by applying
them continuously or resting your
foot
on the pedal. This will result in overheating of the brakes which
could cause unpredictable braking
action, longer stopping distances, or
permanent brake damage.
Accelerator Pedal (3) This pedal controls the speed of the
engine. Depressing the accelerator pedal
increases power output
and speed.
3-9
Starting the Engine
Before Starting the Engine
64J140
1} Make sure the parking brake is set fully. 2} Manual transmission -Shift into UN" (Neutral) and depress the clutch pedal
all the way to the floor. Hold the clutch
pedal while starting the engine.
Automatic transmission -
If the gear­
shift lever is not in Up" (Park) position,
shift into Up" (Park). (If you need to re­start the engine while the vehicle is moving, shift into UN".)
NOTE: Automatic transmission vehicles have a starter interlock device which is designed to keep the starter from operating if the transmission is in any of the drive posi­
tions.
A. WARNING
Make sure that the parking brake is set fully and the transmission is in Neutral (or Park for vehicles with an automatic transmission) before
attempting to start the engine.

Downloaded from www.Manualslib.com manuals search engine OPERATING YOUR VEHICLE
A WARNING
• Reduce your speed and downshift to a lower gear before going down
a long or steep hill. A lower gear
will allow the engine to provide
braking. Avoid riding the brakes or they may overheat, resulting in
brake failure.
• When driving on slippery roads, be
sure to slow down before down­shifting. Excessive and or sudden
changes in engine speed may
cause
loss of traction, which could cause you to lose control.
• Make sure that the vehicle is com­
pletely stationary before you shift into reverse.
CAUTION
• To help avoid clutch damage, do not use the clutch pedal as a foot­rest while driving or use the clutch to keep the vehicle stationary on a
hill. Depress the clutch fully when
shifting.
• When shifting or starting off, do not race the engine. Racing the engine
can shorten engine life and affect
smooth shifting.
3-13
5-Speed Automatic Transmission
EXAMPLE
(1) Power mode selector switch
D:
66J055
5-speed automatic transmission mode 4: 4-speed automatic transmission mode
The 4-speed mode is suitable for the fol­
lowing driving conditions: • Driving on hilly, winding roads
-You can drive more smoothly with less frequent gearshifting
• Going down a steep hill -Some engine braking is provided
NOTE:
With the transfer switch in the "4L LOCK" position, the 5-speed automatic transmis­sion will remain in the 4-speed mode.
Power mode selector switch
A/T
POWER
650448
When you need more power for climbing
hills or smooth starting on slippery road,
push the "AfT POWER" switch. To activate
the power mode selector, push the "AfT POWER" switch, and the "POWER" indica­tor light in the instrument cluster comes on. To deactivate, push the switch again, and
the "POWER" indicator light goes off.
Power driving mode When the "AfT POWER" switch is on with
shift in "0" (Drive), "4" (Low 3) or "3" (Low 2) position, if you depress the accelerator
pedal, the shifting points are delayed so
the engine can rev higher in each gear.
Therefore, you can drive more powerfully than normal driving.

Downloaded from www.Manualslib.com manuals search engine ES~ systems (other than ABS) will be
canceled to provide improved vehicle
traction, and the
~'ESP OFF" indicator
light will come on. When the transfer switch (if equipped) is
turned to the "4L LOCK" position, brake­
traction control can be activated. Brake­
traction control brakes the spinning
wheel to distribute drive power to the other wheels for increased climbing abil­
ity or for better performance on a rolling
hill or a slipe,ery surface .. • If the ESpE> systems operate continu­ously, such as when driving on slippery roads, the traction control functions of the ES~ systems may be canceled
temporarily to avoid overheating the brake pads, and the "ESP OFF" indicator
light will come on. After a short period of time, the ES~ systems (other than ABS) will turn on automatically and the "ESP OFF" indicator light will go out. • If your vehicle is equipped with a hill
descent control system and a hill hold
control system, these systems will not be
turned off
when the "ESP OFF" switch is pushed to turn off the ES~ systems.
E'::.F' OFF I-Qf - -a.'ND S\l',/IT'_ H V"/I)R~;',. I-6-t ONL ',' IN 4HL
79K084
NOTE: If, you push the "ESP OFF" switch when the transfer switch is in the "4H" position, the ES~ systems will not be turned off, and the message shown in the above illus­
tration will appear on the information dis­play. You should turn the transfer switch to the "4H LOCK" position to turn off the ES~ systems. Refer to "Using the Transfer Switch" in this section.
ABS Warning Light I Brake System
Warning Light
See 'Braking" in the "OPERATING YOUR VEHICLE" section.
OPERATING YOUR VEHICLE
Hill descent control System
(if equipped)
The hill descent control system is designed
to reduce the driver's workload when going
down steep, rough and/or slippery hills where the vehicle cannot decelerate enough by engine braking alone. The hill descent control system helps to control
vehicle speed by automatically engaging
the vehicle's brakes, as needed, so you can concentrate on steering the vehicle.
A WARNING
Do not rely excessively on the hill
descent control system. The hill
descent control system may not con­trol vehicle speed on a hill under all load or road conditions. Always be prepared to control vehicle speed by applying the brakes. Failure to pay
attention and control vehicle speed
using the brakes when necessary
may
result in loss' of control or an accident.
3-36