Downloaded from www.Manualslib.com manuals search engine OPERATING YOUR VEHICLE
From 4H to N
64J209
Stop the vehicle completely, place the
transmission in uN" (Neutral) and depress
the brake pedal and the clutch pedal fully (if equipped), then push in and turn the
switch to the mark (1) at the left of the uN" position, and hold the switch in this posi
tion for 5 seconds until the uN" indicator blinks, then turn the switch to the uN" posi
tion. When
you turn the transfer switch to the uN" position, uN" indicator will come on with
the buzzer sound.
3-25
CAUTION
• Be sure to stop the vehicle com
pletely before operating the transfer switch to shift between "N" and "4H", or between "4H LOCK" and "4L LOCK".
• Do not shift between "4H" and "4H
LOCK" unless the front wheels are
in the straight-ahead position and
we recommend
that the vehicle speed be less than 1 00 km/h (60 mph).
Do not operate the transfer switch
while tires are racing.
• Do not operate your vehicle in "4H
LOCK" or "4L LOCK" on dry, hard
surfaces. (Continued)
CAUTION
(Continued) • Do not operate the vehicle while a
4WD mode indicator is blinking except when shifting between "4H" and "4L LOCK".
If you operate the vehicle while a
4WD mode indicator is blinking, a
buzzer will sound and the transfer will shift to "N" (Neutral) to prevent
transfer case damage.
In this case, use the following procedure.
1) Release your foot from the accelerator pedal and depress the
brake pedal to stop the vehicle
completely.
2) Depress the clutch pedal fully (if
equipped) or shift the automatic transmission gearshift lever to the "N" position. 3) If the transfer does not shift from "N" although you perform 1) and 2), turn the transfer switch to the
position previously selected and
operate the switch again.
NOTE: The information display shows the warning
and indicator message when the transfer
system
is operated, or has a problem.
Downloaded from www.Manualslib.com manuals search engine OPERATING YOUR VEHICLE
Warning and Indicator messages
Transfer
Switch Operation Warning
and Indicator messages
In any position
In "N" position
Switching between
"4H" and "4H LOCK"
In "4H" position
3-27
I
79K074
79K077
79K078
I
t¢-I USE 4HL MC'DE
79K079
Master Warning Indicator
Blinks
Blinks
Off
Blinks
Sound
Off
Series
of
Beeps
Off
Beep
Cause and Remedy
There may be a problem with the 4WD
system.
Have your vehicle inspected by an
authorized
SUZUKI dealer.
This message informs you that the
transfer switch is in
"N", which is used only for towing your vehicle,
Move the transfer switch to a different
position
unless you are planning to tow
your vehicle,
This message informs you the 4WD
mode is switching,
Tires are slipping,
Turn the transfer switch to
"4H LOCK" or "4L LOCK" position.
Downloaded from www.Manualslib.com manuals search engine Transfer Switch Operation
Switching between U4H LOCK" and U4L LOCK"
Switching between U4H" and UN"
Warning and Indicator messages
I
1).'110 .8.CCEL ':'FF 1<>1 OE."-.RSHIFT I·.J
79K080
79K081
79K082
I
1<>1 SV'-iIT':Hlf'.JG
79K083
Master Warning Indicator
Off
Off
Off
Off
Sound
Series of Beeps
Series of Beeps
Beep or
Off
Off
OPERATING YOUR VEHICLE
Cause and Remedy
(For automatic transmission)
The desired transfer gear has not been
engaged.
Release your foot from the accelerator
pedal.
Depress the brake pedal.
Shift the automatic transmission gearshift lever to the uN" position.
(For
manual transmission)
The desired transfer gear has not been
engaged.
Release your foot from the accelerator
pedal.
Depress the brake pedal and clutch
pedal.
The desired transfer gear has not been
engaged.
Turn the transfer switch back to the pre
viously selected position, and operate
the transfer switch again.
This message informs
you the 4WD
mode is switching.
Do not move your vehicle.
3-28
