2008 SMART FORTWO COUPE headlamp

Replacing bulbs
256
>> Practical hints. Notes on bulb replacement
• Only use bulbs of the same type and with the
specified watt rating.
• Switch the lights off before replacing a bulb
to prevent short circuits.
• Always use a clean lint
free cloth when
handling bulbs.
• Your hands should be dry and free of oil and
grease.
• Avoid touching the glass of the bulb with
bare fingers.
• If the newly installed bulb does not come on,
contact an authorized smart center.
• Have the bulbs for the front fog lamps*
replaced at an authorized smart center.
Replacing bulbs for front lampsBefore you start to replace a bulb for a front
lamp, do the following first:
>Turn the exterior lamp switch to
positionM (

page 101).
>Switch off the ignition.
>Open the service flap (

page 176)
Left headlamp, (right headlamp in reverse)
1
Bulb socket for parking, and side marker
lamp
2
Bulb socket for turn signal lamp
3
Low beam headlamp cover
4
High beam headlamp coverParking and sidemarker lamp bulb
>Removing:
Driver side: Turn bulb socket
1 toward the
outside.
Passenger side: Turn bulb socket1 toward
the outside.
>Pull bulb socket
1 out of the headlamp
housing.
>Pull the bulb out of bulb socket
1.
> Installing: Insert the new bulb into bulb
socket
1.
>Insert bulb socket
1 into the headlamp
housing.
>Driver side: Turn bulb socket
1 toward the
inside.
Passenger side: Turn bulb socket1 toward
the inside. P82.10
4836
31

Replacing bulbs
>> Practical hints.
257
Low beam headlamp bulb
>Removing: Take off low beam headlamp
cover
3.
>Detach the electrical connector.
>Bend the retainer spring end down and
forward until it unclips. Fold the retainer
spring back.
>Pull the bulb out of the headlamp housing.
>Installing: Insert the new bulb into the
headlamp housing.
>Fold the retainer spring forward.
Bend the retainer spring end forward then
up and back to clip in.
>Attach the electrical connector.
>Reinstall low beam headlamp cover
3.High beam headlamp bulb
>Removing: Take off high beam headlamp
cover
4.
>Detach the electrical connector.
>Tilt the bulb socket down and pull it out.
>Pull the bulb out of the bulb socket.
>Installing: Insert the new bulb into the bulb
socket.
>Fit the bulb so that the retaining lug of the
base plate is pointing up.
>Press the bulb into the bulb socket until it
is fully engaged.
>Attach the electrical connector.
>Reinstall high beam headlamp cover
4.Front turn signal lamp bulb
>Removing: Turn bulb socket
2 counter

clockwise by a quarter of turn and pull it out
of the headlamp housing.
>Press gently onto the bulb and turn it
counterclockwise.
>Pull the bulb out of bulb socket2.
>Installing: Insert the new bulb into bulb
socket
2.
>Press gently onto the bulb and turn it
clockwise.
>Insert bulb socket
2 into the headlamp
housing.
The arrow on bulb socket
2 mu st be in l in e
with the line on the headlamp housing.
>Turn bulb socket
2 clockwise by a quarter
of turn.

Jump starting>> Practical hints.
277 Jump start assistance
Your vehicle’s battery is located in the
passenger’s footwell below the footrest
(
page 273).
For jump starting, use the terminals of the
battery, keeping the leads connected.
>Make sure the two vehicles do not touch.
>Set the parking brake.
>Move the gear selector lever to park
positionP.
>Turn off all electrical accessories.
>Turn off the engine.>Get access to the battery in the passen

ger’s footwell (

page 273).
>Remove the positive terminal cover.
1
Positive terminal of discharged battery
2
Negative terminal of charged battery
3
Positive terminal of charged battery
4
Negative terminal of discharged battery
!
Never invert the terminal connections!>Connect positive terminals
1
and
3 with
the jumper cable.
Clamp the cable to positive terminal3 of
the charged battery first.
>Start the engine of the vehicle with the
charged battery and run at idle speed.
>Connect negative terminals
2 and
4 with
the jumper cable.
Clamp the cable to negative terminal2 of
the charged battery first.
>Start the engine of the disabled vehicle.
You can now turn on the electrical accesso

ries. Do not switch on the headlamps under
any circumstances.
>Remove the jumper cables first from
negative terminals
2 and
4 and then from
positive terminals
1 and
3.
You can now switch on the headlamps.
>Have the battery checked at the nearest
authorized smart center.
G
Warning!
Keep flames or sparks away from battery.
Do not smoke.
Observe all safety instructions and
precautions when handling automotive
batteries (

page 271).P54.10
2749
31