Tires and wheels
182
>> Operation Contact an authorized smart center for infor
mation on tested and recommended rims and
tires for summer and winter operation. They
can also offer advice concerning tire service
and purchase.
Modifications to the brake system and wheels
and the use of spacer and brake dust rings
are not permissible.
Important guidelines• Only use sets of tires and rims of the same
type and make.
• Tires must be of the correct size for the
rim.
• Break in new tires for approximately
60 miles (100 km) at moderate speeds.
• Regularly check the tires and rims for
damage. Dented or bent rims can cause tire
inflation pressure loss and damage to the
tire beads.
• If vehicle is heavily loaded, check tire infla
tion pressure and correct as required.
• Do not allow your tires to wear down too far.
Adhesion properties on wet roads are
sharply reduced at tread depths of less
than
1/8in (3 mm).
G
Warning!
Replace rims or tires with the same des
ignation, manufacturer and type as shown
on the original part. Contact an autho
rized smart center for further informa
tion. If incorrectly sized rims and tires
are mounted:
• The wheel brakes or suspension
components can be damaged.
• The operating clearance of the wheels
and the tires may no longer be correct.
G
Warning!
Worn, old tires can cause accidents. If the
tire tread is badly worn, or if the tires
have sustained damage, replace them.
When replacing rims, only use genuine
smart wheel bolts specified for the
particular rim type. Failure to do so can
result in the bolts loosening and possibly
an accident.
Retreaded tires are not tested or recom
mended by smart, since previous damage
cannot always be recognized on retreads.
The operating safety of the vehicle can
not be assured when such tires are used.
Tires and wheels
>> Operation
183 Tire care and maintenance
Regularly check your tire inflation pressure
at least once a month. For more information on
checking tire inflation pressure, see
"Recommended tire inflation pressure"
(page 189)
.
Tire inspection
Every time you check the tire inflation pres
sure, you should also inspect your tires for
the following:
• excessive treadwear (
page 183)
• cord or fabric showing through the tire’s
rubber
• bumps, bulges, cuts, cracks or splits in the
tread or side of the tire
Replace the tire if you find any of the above
conditions.
Life of tire
The service life of a tire is dependent upon
varying factors including but not limited to:
•Driving style
• Tire inflation pressure
•Distance drivenTread depth
Do not allow your tires to wear down too far.
Adhesion properties on wet roads are sharply
reduced at tread depths of less than
1/8in
(3 mm)
.
Treadwear indicators (TWI) are required by
law. These indicators are located in six places
on the tread circumference and become visi
ble at a tread depth of approximately
1/16in
(1.6 mm), at which point the tire is considered
worn and should be replaced.
Recommended minimum tire tread depth:
Summer tires
1/8in (3 mm)
Winter tires
1/6in (4 mm)
G
Warning!
Regularly check the tires for damage.
Damaged tires can cause tire inflation
pressure loss. As a result, you could lose
control of your vehicle.
Worn, old tires can cause accidents. If the
tire tread is badly worn, or if the tires
have sustained damage, replace them.
G
Warning!
Tires should be replaced after 6 years,
regardless of the remaining tread.
Tires and wheels
184
>> Operation
1
TWI (T
read W
ear I
ndicator)
The treadwear indicator appears as a solid
band across the tread.
Storing tires
!
Keep unmounted tires in a cool, dry place
with as little exposure to light as possible.
Protect tires from contact with oil, grease and
gasoline.Cleaning tires
!
Never use a round nozzle to power wash
tires. The intense jet of water can result in
damage to the tire.
Always replace a damaged tire.
Direction of rotationUnidirectional tires offer added advantages,
such as better hydroplaning performance.
To benefit, however, you must make sure the
tires rotate in the direction specified.
An arrow on the sidewall indicates the
intended direction of rotation (spinning) of
the tire.
G
Warning!
Although the applicable federal motor
safety laws consider a tire to be worn
when the treadwear indicators (TWI) be
come visible at approximately
1/16in
(1.6 mm), we recommend that you do not
allow your tires to wear down to that
level. As tread depth approaches 1/8in
(3 mm), the adhesion properties on a wet
road are sharply reduced.
Depending upon the weather and/or road
surface (conditions), the tire traction
varies widely.
Tires and wheels
186
>> Operation Tire and Loading InformationTire and Loading Information placard
i
Data shown on Tire and Loading Informa
tion placard example are for illustration pur
poses only. Load limit data are specific to
each vehicle and may vary from data shown in
the following illustration. Refer to Tire and
Loading Information placard on vehicle for
actual data specific to your vehicle.
1
Load limit information on the Tire and
Loading Information placardThe Tire and Loading Information placard
showing the load limit information is located
on the driver’s door Bpillar (
page 185).
>Locate the statement "The combined weight
of occupants and cargo should never
exceed XXX kg or XXX lbs." on the Tire and
Loading Information placard.
The combined weight of all occupants and
cargo / luggage should never exceed the
weight referenced in that statement.
Seating capacity
The seating capacity gives you important
information on the number of occupants that
can be in the vehicle. The Tire and Loading
Information placard showing the seating
capacity is located on the driver’s door
Bpillar (
page 185)
.
G
Warning!
Do not overload the tires by exceeding
the specified load limit as indicated on
the Tire and Loading Information placard
on the driver’s door Bpillar. Overload
ing the tires can overheat them, possibly
causing a blowout. Overloading the tires
can also result in handling or steering
problems, or brake failure.
Tires and wheels
>> Operation
189
Certification label
Even after careful determination of the
combined weight of all occupants and cargo as
to not exceed the permissible load limit, you
must make sure that your vehicle never
exceeds the Gross Vehicle Weight Rating
(GVWR) and the Gross Axle Weight Rating
(GAWR) for either the front or rear axle. You
can obtain the GVWR and GAWR from the
certification label. The certification label can
be found on the driver’s door Bpillar, see
"Technical data" (
page 293).
Gross Vehicle Weight Rating (GVWR) means:
the total weight of the vehicle, all occupants,
and all cargo must never exceed the GVWR.
Gross Axle Weight Rating (GAWR) means:
the total allowable weight that can be carried
by a single axle (front or rear).To assure that your vehicle does not exceed
the maximum permissible weight limits (GVWR
and GAWR for front and rear axle), have the
loaded vehicle (including driver, passenger,
and all cargo) weighed on a suitable commer
cial scale.
Recommended tire inflation
pressure
Your vehicle is equipped with the Tire and
Loading Information placard located on the
driver’s door Bpillar (
page 185).
The tire inflation pressure should be checked
regularly and should only be adjusted on cold
tires. The tires can be considered cold if the
vehicle has been parked for at least 3 hours
or driven less than 1 mile (1.6 km).
G
Warning!
Follow recommended tire inflation
pressures.
Do not underinflate tires. Underinflated
tires wear excessively and/or unevenly,
adversely affect handling and fuel econ
omy, and are more likely to fail from being
overheated.
Do not overinflate tires. Overinflated
tires can adversely affect handling and
ride comfort, wear unevenly, increase
stopping distance, and result in sudden
deflation (blowout) because they are
more likely to become punctured or
damaged by road debris, potholes etc.
Do not overload the tires by exceeding
the specified load limit as indicated on
the Tire and Loading Information placard
on the driver’s door Bpillar. Overload
ing the tires can overheat them, possibly
causing a blowout. Overloading the tires
can also result in handling or steering
problems, or brake failure.
Tires and wheels
190
>> Operation Follow recommended cold tire inflation pres
sures listed on Tire and Loading Information
placard on the driver’s door Bpillar.
Keeping the tires properly inflated provides
the best handling, tread life and riding com
fort.
For more information, see "Important notes on
tire inflation pressure" (
page 190).
i
Data shown on Tire and Loading Informa
tion placard example are for illustration pur
poses only. Tire data are specific to each
vehicle and may vary from data shown in the
following illustration. Refer to Tire and Load
ing Information placard on vehicle for actual
data specific to your vehicle.
1
Tire and Loading Information placard
with recommended cold tire inflation
pressures
The Tire and Loading Information placard
lists the recommended cold tire inflation
pressures for maximum loaded vehicle weight.
The tire inflation pressures listed apply to the
tires installed as original equipment.Important notes on tire inflation pressure
Tire temperature and tire inflation pressure
are also increased while driving, depending
on the driving speed and the tire load.
Tire inflation pressure changes by approxi
mately 1.5 psi (0.1 bar) per 18°F (10°C) of air
temperature change. Keep this in mind when
checking tire inflation pressure where the
temperature is different from the outside
temperature.
G
Warning!
If the tire inflation pressure drops
repeatedly:
• Check the tires for punctures from
foreign objects.
• Check to see whether air is leaking
from the valves or from around the rim.
Tires and wheels
>> Operation
191 Checking tire inflation pressure
Regularly check your tire inflation pressure
at least once a month.
Check and adjust the tire inflation pressure
when the tires are cold. The tires can be con
sidered cold if the vehicle has been parked
for at least 3 hours or driven less than 1 mile
(1.6 km).
If you check the tire inflation pressure when
the tires are warm (the vehicle has been
driven for several miles or sitting less than
3 hours), the reading will be approximately
4 psi (0.3 bar) higher than the cold reading.
This is normal. Do not let air out to match the
specified cold tire inflation pressure. Other
wise, the tire will be underinflated.Checking tire inflation pressure manually
Follow the steps below to achieve correct tire
inflation pressure:
>Remove the cap from the valve on one tire.
>Firmly press a tire gauge onto the valve.
>Read tire inflation pressure on tire gauge
and check against the recommended tire
inflation pressure on the Tire and Loading
Information placard on the driver’s door
Bpillar (
page 185). If necessary, add air
to achieve the recommended tire inflation
pressure.
i
If you have overfilled the tire, release tire
inflation pressure by pushing the metal stem
of the valve with e.g. a tip of a pen. Then
recheck the tire inflation pressure with the
tire gauge.
>Install the valve cap.
>Repeat this procedure for each tire.
G
Warning!
Follow recommended tire inflation
pressures.
Do not underinflate tires. Underinflated
tires wear excessively and/or unevenly,
adversely affect handling and fuel econ
omy, and are more likely to fail from being
overheated.
Do not overinflate tires. Overinflated
tires can adversely affect handling and
ride comfort, wear unevenly, increase
stopping distance, and result in sudden
deflation (blowout) because they are
more likely to become punctured or
damaged by road debris, potholes etc.
Do not overload the tires by exceeding
the specified load limit as indicated on
the Tire and Loading Information placard
on the driver’s door Bpillar. Overload
ing the tires can overheat them, possibly
causing a blowout. Overloading the tires
can also result in handling or steering
problems, or brake failure.
Tires and wheels
192
>> Operation Checking tire inflation pressure electroni
cally with the Tire Pressure Monitoring
System (TPMS)
i
The
Tire
Pressure
Monitoring
System
(TPMS) is equipped with a combination low tire
pressure/TPMS malfunction telltale in the
instrument cluster (
page 34). Depending on
how the telltale illuminates, it indicates a low
tire pressure condition or a malfunction in the
TPMS system itself:
• If the telltale illuminates continuously,
one or more of your tires is significantly
underinflated. There is no malfunction in
the TPMS.
• If the telltale flashes for 60 seconds and
then stays illuminated, the TPMS system
itself is not operating properly.
i
USA only:
This device complies with Part 15 of the
FCC Rules. Operation is subject to the follow
ing two conditions:
(1) This device may not cause harmful inter
ference, and
(2) this device must accept any interference
received, including interference that may
cause undesired operation.
Any unauthorized modification to this device
could void the user’s authority to operate the
equipment.
i
Canada only:
This device complies with RSS210 of Industry
Canada. Operation is subject to the following
two conditions:
(1) This device may not cause interference,
and
(2) this device must accept any interference
received, including interference that may
cause undesired operation of the device.
Any unauthorized modification to this device
could void the user’s authority to operate the
equipment.The TPMS only functions on wheels that are
equipped with the proper electronic sensors.
It monitors the tire inflation pressure in all
four tires. A warning is issued to alert you to
a decrease in pressure in one or more of the
tires.
G
Warning!
The Tire Pressure Monitoring System
(TPMS) does not indicate a warning for
wrongly selected inflation pressures.
Always adjust tire inflation pressure
according to the Tire and Loading Infor
mation placard on the driver’s door
Bpillar.
The TPMS is not able to issue a warning
due to a sudden dramatic loss of
pressure (e.g. tire blowout caused by a
foreign object). In this case bring the
vehicle to a halt by carefully applying the
brakes and avoiding abrupt steering
maneuvers.