2008 Seat Leon 5D lock

Quick Reference Guide
4
Entries in the screen menus can be made using the menu
button. Rotating the button selects a function or a submenu or
adjusts a value. Pressing confirms the selection
Backwards/forwards keys, apply to the active audio
source
− Press: in Radio mode : changes station; in CD mode changes
song (“track”)
− Press and hold: in Radio mode, manual station selection; in
CD mode fast forward/backward search
On/off knob (push) and volume control (turn). The volume
control will regulate the volume of the audio source currently
selected. A bar on the screen accompanied by a value indicates
the volume. IF the value is “0”, there is no sound. This control
may also be used to adjust the volume of a telephone conversa-
tion or a spoken navigation message.
The main menu buttons
− Repeat the last audio navigation instruction and show
the current destination, position (direction) and the
geographical position.
− Activates the radio mode. . . . . . . . . . . . . . . . . . . . . .
− Activates the CD mode. . . . . . . . . . . . . . . . . . . . . . . . . .
− Goes to Navigation mode. . . . . . . . . . . . . . . . . . . . . . .
− Shows the traffic reports from the current TMC
( T raffic- Message- Channels) ⇒page 51, “Dynamic destina-
tion guide with TMC (Traffic Message Channel)”. Press the
function selector button goes directly to the
“route options” to make, for example, changes in the route
⇒ page 42, “Route options”. During the guided navigation,
a section of a route may be manually excluded pressing or re-included pressing .
⇒ page 55, “To block sections and consult information from
a route”. −
The button allows adjustments to made in the selec-
tion area, on the screen (Function keys and
) and on the equipment ⇒ page 15, “Radio
adjustments (SETUP)” and ⇒page 48, “Navigation settings
(SETUP)”.
Screen function keys. Correspond ing function indicated on the
screen close to the button. The brackets indicate that the func-
tion is temporarily not available (for example [ERASE] if no entry
has been made).
⇒ page 9, “Sound, sound focus and volume”.
Slot for an audio or navigation CD .
Screen, adjustments on ⇒page 8, “System settings”.
CD eject button. The ejected CD will be pulled back into the
unit if it is not fully withdrawn within 10 seconds.
Set flagged destination. The unit will store the current
vehicle position when this button is pressed ⇒page 45, “To
record or select a final destination, intermediate destinations,
destinations with a flag or current position”..
Return to the previous menu, to the previous adjustment
and the main menu selected using the function keys.
WARNING
Adjust the volume so that you can still hear signals coming from outside
the vehicle, such as those of the fire brigade, ambulances or police cars.
Caution
•
The screen is not a touch screen. Do not press on the surface. The screen
can be cleaned with a soft cloth (and alcohol, if necessary). Do not use
solvents such as turpentine or petrol to clean the surface as they will corrode
the material.
A1A2


A3A4
INFORADIO
11
CD
16
NAV
34
TRAFFIC
OPCS. ROUTE
TRAFFIC JAM
ERASE. TRAFFIC JAM.
SETUP
BRIGHTNESS
OFF. SCREEN
A5A6

A7A8A9

A10

A11

RNS MP3_ingles Seite 4 Mittwoch, 10. Mai 2006 7:52 19

Quick Reference Guide
6After turning the equipment on, the sound source previously active is
selected. The equipment will be switched off if the ignition is turned off. It is
possible to turn the equipment on when the ignition is off. It will be switched
off automatically after an hour to stop the vehicle battery from running down.
If no CD is inserted in the reader, the message Insert the navigation CD will
be displayed after the pin has been entered pressing .
If you do not wish to use the navigation system immediately, you can still
select a different audio source by pressing the appropriate button. Unit card
The code number is printed on a unit card together with the serial number.
This card can be found at the front of the vehicle wallet.
The unit card must be kept in a safe
place - under no circumstances in the
vehicle! Without the code, the unit be useless to unauthorized persons.
Note
If the code is introduced incorrectly twice, the equipment will remain locked
for one hour ( System locked on the screen). After, the correct code may be
entered. The equipment must re main on during this time.
Handling the menusThe menu button may be used to access nearly all of the functions and to adjust them.
OK
Fig. 3 Example
RNS MP3_ingles Seite 6 Mittwoch, 10. Mai 2006 7:52 19

Navigation39
– To enter stages, route lists, route options and blocked sections
⇒ page 42, “Route options”
– Displays the vehicle position. The actual vehicle position is
displayed as an address (if the location is on the navigation CD) and coordi-
nates. The direction of travel is indicated using a compass on the left hand
side of the screen. The SETUP menu may be used to manually enter the
vehicle position ⇒page 48. While the destination guide is working, visual
indications will be given using symbols ⇒page 53.
– Starts destination guide to the indicated destination. The
guide may be stopped using the function ⇒page 50, “Destina-
tion guide”.
Function buttons used to enter numbers and figures
– To erase the character to the right hand side of the screen (only acti-
vated after entering characters).
– Shows a list from which the destination may be selected.
button on the NAVIGATION menu
More options are available in the Navigation setup menu ⇒page 48.Note
•
If the destination is changed while the guide is being used, you will be
asked if you wish to substitute the actual destination or to indicate a stage. If
a stage is added, route planning is automatically selected ⇒ page 40.
•
A mark may be displayed under certain letters. If these letters are marked
then, after a few seconds, special related symbols will appear (see also
⇒ page 45, fig. 24 ).
•
The entries between square brackets [ ... ] can neither be selected or
edited; insufficient data may have been entered. In the case of address, for
example, the country must first be entered followed by the town then finally
the address.ROUTESYMBOLSSTART GUIDE
END GUIDE
ERASELIST / OKSETUP
RNS MP3_ingles Seite 39 Mittwoch, 10. Mai 2006 7:52 19

Navigation
42Route options– Press the button and then the function button to
access the route settings.
– Select the options from the list by turning and pushing the menu knob.Route with intermediate destinations
If this function is active (black box), various destinations may be entered
(⇒ page 40, “Route planning”).
Route list
Selecting this option with the destination guide active, all of the journey
sections may be consulted up to the following destination or stage
⇒ page 55, “To block sections and consult information from a route”. Route options
The route options may be accessed by pressing and the function
button
on the following menu.
Dynamic navigation : The dynamic navigation takes the traffic reports from a
TMC station into account ( TMC = Traffic Message Channel). If necessary,
another route will automatically be selected if the planned route is blocked or
if there are traffic jams. For this, a TMC station must be available (see
⇒ page 51, “Dynamic destination guide with TMC (Traffic Message
Channel)”. To consult the latest reports, press the button .
Route opt.:
•
Short: The shortest route is calculated even if it implies a longer trip time.
•
Fast : This option calculates the fastest route to a destination, even
though deviations may be selected.
•
Optimal : This function searches for a balance between minimum time and
trip distance.
Fig. 21 Route settings
NAV
ROUTE
TRAFFIC
ROUTE OPTIONS
TRAFFIC
RNS MP3_ingles Seite 42 Mittwoch, 10. Mai 2006 7:52 19

Navigation43
Route options can be altered whilst the destination guide function is active.
The changed parameters will be used as a basis for the calculation of the
remaining journey.
Highway , Ferry , To l l or Tunnel : Establishes if the sect ion of a route includes
highways, a ferry, toll roads or tunnels. These options will, however, be used
for route planning if there is no other logical route to the destination (e.g. an
island is to be used without using a ferry) (“ No”).
To avoid a route from a point
During the destination guide, this option may be used to manually block a
section of the route on the menu which follows ⇒page 55, “To block
sections and consult information from a route”.
Note
•
The dynamic route guide option will only function if you are receiving at
least one TMC radio station. During the destination guide, the TMC station
must be selected if the sound source is the radio.
•
The quality of the dynamic destinatio n guide depends on the information
contained in the traffic announcements. The stations and / or traffic informa-
tion providers are responsible for the quality of the information given.
•
In some cases, in order to avoid a traffic jam using the TMC instructions,
no benefit is noticeable if traffic is heavy on the alternative route.
To select a destination using its geographical position
A destination can be entered using the exact coordinates for
longitude and latitude.– Press the button.
–Press Position if you want to enter your destination using coordi-
nates. – Use the menu button to enter
the degrees, minutes and seconds
of the location.
If the coordinates entered do not correspond to the information on the navi-
gation CD, the destination guide cannot begin. Use the following data to esti-
mate the position of your location:
For latitude, 1° corresponds to approximately 111 km, 1 arc minute approxi-
mately 1.85 km and 0.1 hundredth of an arc minute approximately 3 m
For longitude, 1° corresponds to approximately 69 km, 1 arc minute approxi-
mately 1.15 km and 0.1 hundredth of an arc minute approximately 3 m
Note
If you set the longitude higher than 180° or lower than 0°, the E will be
replaced by a W (western longitude). Latitudes can be set from 90°N via 0° to
90°S and back only.
NAV
RNS MP3_ingles Seite 43 Mittwoch, 10. Mai 2006 7:52 19

Navigation55
To block sections and consult information from a route
Sections of a route may be manually blocked. The route list is a list of all route sections that will be travelled through. To block sections manually
– During the active destination guide, press the button to
acce ss the main TRAFFIC me
nu.
– Press the function button . The menu Block the route
from this point is displayed.
–In the menu Block the route from this point , enter the length of
the block by rotating the menu button.
– Confirm the entry by pressing the menu button. The new route will be drawn.
– It is also possible to access this option by pressing the function key from the main navigation menu and then Avoid route
from this point ⇒ page 42 To eliminate a block
– Press the function key in the
TRAFFIC main menu.
– This may also be done by pressing the function button from the main navigation menu and deactivating the function
Block the route from this point ⇒ fig. 28 using the menu button.
Consult the route list
– During the destination guide, press the function button from the main navigation menu.
– Select the option Route list to consult the stretches remaining on
the trip ⇒fig. 28 .
Only stretch from the active destination guide can be blocked.
Fig. 28 To access the route list
TRAFFIC
JAM AHEAD
ROUTE
ERASE JAM
ROUTEROUTE
RNS MP3_ingles Seite 55 Mittwoch, 10. Mai 2006 7:52 19

Navigation
56You will be guided through a blocked area if there is no logical alternative to
travelling through it.
Route list
The route list is updated during the journey. It shows the roads or streets that
you have not yet reached. Route sections that you have already travelled will
be deleted from the route list.
Pressing the menu button, more info rmation can be found on different
stretches. The blocked stretches are indicated by the symbol “ !” in a black
box.
Note
•
It takes some seconds after the destination guide has started for the route
list to be compiled for display.
•
The type and the quantity of the proposed alternative routes in case of a
blockage depends on the navigation CD content.
The destination guide without the navigation CD
With the destination guide active, the navigation CD may be
changed for an audio CD.The navigation function is still available, although in a limited form, without
the corresponding CD. In this case, the internal reader may be used to play an
audio or MP3 CD without having to reinsert the navigation CD. For this, all of
the data on the CD concerning the route is stored in the “temporary memory”
and with the data from this “tempo rary memory” the destination entry
dynamic TMC guide options are limited. The “content” of the temporary
memory depends on the length of the route that must be recorded. The
shorter the route, the more details may be stored in the temporary memory
and the more functions will be available without any need to insert the navi-
gation CD. If the route is long, or unexpected deviations are taken (for example, to avoid a traffic jam based on
TMC reports), the navigation CD will
be requested to resume the destination guide.
In the navigation menu, the equipment in dicates that it is transferring data
from the navigation CD to the temporary memory by a CD symbol after the title
NAVIGATION; The navigation CD can only be removed when this symbol
disappears. If the navigation CD is removed anyway, the route calculation or
destination guide can not be resumed correctly.
During the destination guide using stored data, that is, without the naviga-
tion CD, the CD symbol appears crossed out.
RNS MP3_ingles Seite 56 Mittwoch, 10. Mai 2006 7:52 19

Index59
Position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Preselect buttons . . . . . . . . . . . . . . . . . . . . . . . . . 14QQuick reference guide . . . . . . . . . . . . . . . . . . . . . . 3RRadio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Radio equipment
compatible . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Random playback . . . . . . . . . . . . . . . . . . . . . . . . 27
Random track selection MIX CD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
MP3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Recent destinations . . . . . . . . . . . . . . . . . . . . . . . 46
Remove iPod . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Rewind . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Route entering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Route guidance . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Route list . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42, 55
Route memory . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Route options . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Route planning . . . . . . . . . . . . . . . . . . . . . . . . . . 40 destination guide . . . . . . . . . . . . . . . . . . . . . 50
to access the menu . . . . . . . . . . . . . . . . . . . . 40
to leave the menu . . . . . . . . . . . . . . . . . . . . . 38
Route with stages . . . . . . . . . . . . . . . . . . . . . . . . 42
SSCAN MP3 track search . . . . . . . . . . . . . . . . . . . . . . 19
plays each station briefly in Radio mode . . . 12
track search . . . . . . . . . . . . . . . . . . . . . . . . . . 17
SETTINGS to display the ID3 of MP3 files . . . . . . . . . . . 19
SETUP button navigation . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Skipping songs . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Special destinations . . . . . . . . . . . . . . . . . . . . . . 44
Special destinations nearby . . . . . . . . . . . . . . . . 46
Station list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Switching off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Switching on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Symbol representation visual navigation indication . . . . . . . . . . . . . 53TTelephone volume . . . . . . . . . . . . . . . . . . . . . . . . 10
TemperatureAmbient . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Temporary memory . . . . . . . . . . . . . . . . . . . . . . . 56
Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
TMC Traffic Message Channel . . . . . . . . . . . . . . . . 51
TMC and the dynamic destination guide . . . . . . 51
To block sections . . . . . . . . . . . . . . . . . . . . . . . . . 55 To eliminate a block . . . . . . . . . . . . . . . . . . . . . . 55
To enter a destination
geographic position . . . . . . . . . . . . . . . . . . . 43
special destinations . . . . . . . . . . . . . . . . . . . 44
To erase itineraries . . . . . . . . . . . . . . . . . . . . . . . 48
To input the destination trip destination . . . . . . . . . . . . . . . . . . . . . . . 37
To manually enter the current position . . . . . . . 48
To save the actual position . . . . . . . . . . . . . . . . . 47
TP (Traffic Program) Traffic reports . . . . . . . . . . . . . . . . . . . . . . . . . 15
Track search SCAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
TRAFFIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
TRAFFIC button ROUTE OPTIONS . . . . . . . . . . . . . . . . . . . . . . . 42
to display the traffic reports . . . . . . . . . . . . . 52
to eliminate a block . . . . . . . . . . . . . . . . . . . . 55
to insert a block . . . . . . . . . . . . . . . . . . . . . . . 55
Traffic jam function . . . . . . . . . . . . . . . . . . . . . . . 55
Traffic problems dynamic destination guide . . . . . . . . . . . . . . 52
Traffic reports . . . . . . . . . . . . . . . . . . . . . . . . . 10, 15 adjust the volume . . . . . . . . . . . . . . . . . . . . . 15
display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Turn sound off . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Tyre calibration . . . . . . . . . . . . . . . . . . . . . . . . . . 48
UUSB* connection . . . . . . . . . . . . . . . . . . . . . . . . . 28
RNS MP3_ingles Seite 59 Mittwoch, 10. Mai 2006 7:52 19