Page 246 of 293

If and when245
Safety First
Operating instructions
Practical tips
Te c h n i c a l D a t a
Rear tailgate light unit
Fog light (driver's side) - P21W
Reverse (passenger's side) - P21W
Position - W5W
Side indicator
Side indicator - W5W
Registration plate light
Registration plate light - C5W
Glove box lamp
Glove box lamp - W5W
Note
•
Depending on weather conditions (cold
or wet), the front lights, the fog
lights, the rear lights and the indicators may be temporarily misted. This has
no influence on the life expectancy of the lighting system. By switching on the
lights, the area through which the beam of light is projected will quickly be
demisted. However, the edges may continue to be misted.
•
Please check at regular intervals that all lighting (especially the exterior
lighting) on your vehicle is functioning properly. This is not only in the interest
of your own safety, but also in that of all other road users.
•
Due to the difficulty in accessing the lamps, any replacement work should
be done by a SEAT dealer. However, th e following is a description of how to
change the lamps except for the fog lights* and interior lamps.
Main headlight lamps
Indicator
Dipped headlights
Main beam headlights
Side lights
Fig. 158 Main headlight
lamps
AAABACAD
leon_ingles Seite 245 Montag, 26. Januar 2009 4:29 16
Page 247 of 293
If and when
246Tu r n si g nal l a m ps– Raise the bonnet.
– Rotate the lamp holder ⇒fig. 159 to the left and pull.
– Remove the bulb by pressing on the lamp holder and rotating at the same time to the left.
– Installation is done in the reverse order.
Dipped beam lights–Raise the bonnet
Fig. 159 Turn signal
lamps
AA
Fig. 160 Dipped head-
lightsFig. 161 Dipped head-
lights
leon_ingles Seite 246 Montag, 26. Januar 2009 4:29 16
Page 248 of 293
If and when247
Safety First
Operating instructions
Practical tips
Te c h n i c a l D a t a
– Remove the loops ⇒page 246, fig. 160 in the direction of
the arrow and remove the cover.
– Remove the connector ⇒page 246, fig. 161 from the bulb.
– Disengage the retainer spring ⇒ page 246, fig. 161 pressing
inwards to the right.
– Extract the bulb and fit the replacement so that the rim of the attachment plate is on the reflector cut-out.Main beam lights
– Raise the bonnet
– Remove the cover ⇒fig. 162 by pulling on this.
– Remove the connector ⇒fig. 163 from the bulb.
– Press the spring ⇒fig. 163 inwards and to the right.
– Extract the bulb and fit the replacement so that it sits correctly into the cut-out on the reflector.
– Installation is done in the reverse order.
A1
A2
A3
Fig. 162 Main beam
headlights
Fig. 163 Main beam
headlights
AC
A1
A2
leon_ingles Seite 247 Montag, 26. Januar 2009 4:29 16
Page 249 of 293
If and when
248Side lights– Raise the bonnet.
– Remove the cover ⇒fig. 164 by pulling on this. – Extract the lamp holder
⇒fig. 165 outwards.
– Replace the bulb by pulling this out and inserting the replace- ment.
– Installation is done in the reverse order.
Rear lights•
On the body
- Indicator, side and brake light
•
On the tailgate
- Left side: position and fog lights.
- Right side: reverse and position.
Fig. 164 Side lightsFig. 165 Side lights
AD
A1
leon_ingles Seite 248 Montag, 26. Januar 2009 4:29 16
Page 250 of 293
If and when249
Safety First
Operating instructions
Practical tips
Te c h n i c a l D a t a
Indicator, side and brake lights on the bodywork– Press on the side pin outwards and take out the lamp holder.
– Extract the failed bulb and change it for a new one.
– To refit follow the steps in reverse order, taking special care when
fitting the lamp holder.
Position light, fog light and reverse light on the tailgate–Open the tailgate.
– Pull the cover off. See the arrow ⇒ fig. 167.
Fig. 166 Indicator, side
and brake lights on the
bodywork
Fig. 167 Lights on the
tailgateFig. 168 Removing the
lampholder
leon_ingles Seite 249 Montag, 26. Januar 2009 4:29 16
Page 252 of 293
If and when251
Safety First
Operating instructions
Practical tips
Te c h n i c a l D a t a
Luggage compartment lights– Remove the bulb by pressing on the inside edge of this -arrow-
using the flat side of a screwdriver ⇒fig. 170 . – Press the lamp sideways and remove from its housing
⇒fig. 171.
– Installation is in the reverse order.
Fig. 170 Luggage
compartment lightFig. 171 Luggage
compartment light
leon_ingles Seite 251 Montag, 26. Januar 2009 4:29 16
Page 253 of 293
If and when
252Registration light– To remove the tulip-shaped fitting, unscrew the bolts ⇒fig. 172 .– Remove the bulb, moving it in the direction of the arrow and
outwards ⇒fig. 173 .
– Installation is in the reverse order.
Glove box lamp*– Insert screwdriver above, between the light and the glove box.
– Carefully remove the light Next lift the light out sideways.
– Replace the bulb.
– Insert the light on the connector side, first underneath then push at the top until it clicks into place.
Fig. 172 Registration
lightFig. 173 Registration
light
leon_ingles Seite 252 Montag, 26. Januar 2009 4:29 16
Page 254 of 293

If and when253
Safety First
Operating instructions
Practical tips
Te c h n i c a l D a t a
Sunroof light– Carefully remove the lamp, using the flat side of the screwdriver,
as shown in the figure ⇒fig. 175. – Remove the bulb, moving it in
the direction of the arrow and
outwards ⇒fig. 175.
– Installation is in the reverse order.
Jump-startingJump leads
The jump lead must have a sufficient wire cross section.If the engine fails to start because of a discharged battery, the battery can be
connected to the battery of another vehicle to start the engine.
Jump leads
Jump leads must comply with the standard DIN 72553 (see manufacturer's
documentation). The wire cross section must be at least 25 mm
2 for petrol
engines and at least 35 mm
2 for diesel engines.
Note
•
The vehicles must not touch each othe r, otherwise electricity could flow as
soon as the positive terminals are connected.
•
The discharged battery must be properly connected to the vehicle elec-
trical system.
Fig. 174 Removing
sunroof lightFig. 175 Removing
sunroof light
leon_ingles Seite 253 Montag, 26. Januar 2009 4:29 16