2008 Seat Exeo display

Cockpit
84On-board computerIntroduction
The on-board computer provides you with useful information
during a journey, includin g average and current fuel
consumption, average speed, fuel range, driving time and
distance covered.Press RESET button ⇒page 85, fig. 59 to switch back and forward
between the functions of on-board computers 1 and 2.
The numbers in the display ⇒fig. 58 indicates which of the two memories is
currently in use. The figure 1 means that the display is showing the informa-
tion in the single journey memory (on-board computer 1). The figure 2 means
that the display is showing the inform ation in the total journey memory (on-
board computer 2). Single-journey memory (on-board computer 1)
The single-journey memory processes th
e information on a journey from the
time the ignition is switched on until it is switched off. If the journey is
resumed within two hours after the ignition is switched off, the new figures
are automatically included in the calculation. If the journey is interrupted for
more than two hours the stored information is automatically erased when you
resume your journey.
Total-journey memory (on-board computer 2)
Unlike the single-journey memory, the total-journey memory is not erased
automatically. Hence, you can determine the period for which you wish the
on-board computer to supply figures.
Fuel range
The estimated fuel range is displayed in km. The fuel range is displayed in
increments of 10 km.
Average fuel consumption
This mode shows the average fuel consumption since the memory was last
cancelled in litres/100 km.
Instantaneous fuel consumption
The display shows the instantaneous fuel consumption in litres/100 km.
When the vehicle is stationary, the computer will display the last value in the
memory.
Average speed
This mode shows the average speed driven since the memory was last
cancelled (in km/h).
Driving time
This display shows the period of time which has elapsed since the memory
was last cancelled. The longest possible period it can cover is 999 hours and
59 minutes.
Fig. 58 On-board
computer: memory 1
AB
Exeo_EN.book Seite 84 Freitag, 17. Oktober 2008 11:24 11

Cockpit85
Safety First
Operating instructions
Practical tips
Te c h n i c a l D a t a
Driving time warning
After 2 hours of continuous driving, the display automatically switches over
to the driving time display of
2:00. At the same time the driving time display
starts flashing. This is to remind the driver to take a break.
The driving time warning can be switched off by briefly pressing the function
selector switch or the button ⇒fig. 59 .
If you continue driving or take a break for less than 10 minutes, the driving
time warning will switch on once agai n when the total driving time is 4:00
hours, 6:00 hours, etc. However, if you take a break for more than 10 minutes,
the driving time warning clock will be erased.
Distance covered
This display shows the distance you have covered since the memory was last
cancelled. The longest possible distance which can be recorded is
9999.9 km.
Note
•
The displays for fuel consumption (average and instantaneous), fuel
range and speed are shown in metric units.
•
The information in the memory is lost if the battery is disconnected.
Operating
The on-board computer is controlled by means of two
switches on the windscreen wiper lever.Enabling the on-board computer
– Press the reset button repeatedly until the on-board computer (memory 1 or 2) ⇒page 84, fig. 58 is displayed.
Selecting the function
– Press the top or bottom of the function selector switch ⇒fig. 59 . This displays the functions of the on-board computer
in sequence.
Resetting to zero
– Press and hold the Reset button for at least two seconds.The following values can be reset to zero using the Reset button:
Reset
Fig. 59 Windscreen wiper
lever: On-board computer
controls
AB
AA
AB
Exeo_EN.book Seite 85 Freitag, 17. Oktober 2008 11:24 11

Cockpit
86•
Journey duration
•
Distance covered
•
Average fuel consumption
•
Average speed
The on-board computer can only be oper ated when the ignition is switched
on. When the ignition is switched on, the display shows the function that was
last selected.
As well as the figures from the on-boa rd computer (computer 1 or 2), the
display can also show information from the navigation system*. Press the
Reset button briefly to switch back and forward between these displays.Note
•
If you keep the Reset button pressed for longer than two seconds, it will
reset the currently displayed figure to zero (for instance average fuel
consumption).
•
Faults detected by the auto-check control will be displayed even if the
display is off.
•
The information in the memory is lost if the battery is disconnected.
Menu displayIntroduction
AB
Fig. 60 Windscreen wiper
lever: Menu selection
buttonFig. 61 Display: Main
menu
Exeo_EN.book Seite 86 Freitag, 17. Oktober 2008 11:24 11

Cockpit87
Safety First
Operating instructions
Practical tips
Te c h n i c a l D a t a
Some of the functions in your vehicle can be adjusted, activated and
controlled via
menus (e.g. tyre pressure*). With the aid of the menus you can
then also select the information you wish to see displayed on the DIS display.
This is only possible when the ignition is on. The menu is enabled using the
button on the windscreen wiper lever ⇒page 86, fig. 60 .
The main menu lists the different display types (or basic commands):
Programming
Check
Menu off
Help
The main menu options have the following submenus:
Controlling the menu
The menu display is called up via the button and the
rocker switch on the windscreen wiper lever. Use these
controls to make checks and adjust the settings.Functions of the ⇒fig. 62 and the rocker switch :
Enabling the menu
– Press the button until the menu display ⇒page 86,
fig. 61 appears.
Selecting and setting
– Press the rocker switch to select one of the menus. Press "up" or "down" on the switch to select the options accordingly.
Entering and confirming
– Press the button.
Programming
Clock
⇒ page 87
Computer
⇒page 87
Speed warning
⇒page 81
Radio info (on/off)Units: for measuring dis-
tance, fuel consumption and
temperature
⇒page 87
Language: you can select
one of 6 languages.
⇒page 87
Check
Service
⇒page 74
Menu off
When the menu is switched off, the display shows the
same information as on vehicles without the menu func-
tion.
Help
This function helps you select the options you require.
Reset
Reset
Fig. 62 Windscreen wiper
lever: Reset button and
rocker switch
Reset
AB
AA
ResetReset
Exeo_EN.book Seite 87 Freitag, 17. Oktober 2008 11:24 11

Cockpit
88Use the rocker switch to select the menus and adjust various values. The
selected values are highlighted on a red background.
By pressing the button, you can conf irm the option you have selected
or the value you have set. Selected functions are marked with a tick.
The following symbols are used:Tyre pressure monitoringIntroduction
The tyre pressure monitoring system constantly checks the
pressure of the tyres.The system warns the driver in the event of a loss of pressure by means of
symbols and messages in the instrument panel display. The system works
with the help of the ABS sensors in the wheels.
Please bear in mind that the tyre inflation pressure is also influenced by the
temperature of the tyre. Tyre pressure increases about 0.1 bar for each 10°C
in tyre temperature increase. The tyre heats up while the vehicle is being driven and the tyre pressure will rise accordingly. Therefore, you should only
adjust the tyre pressures when they are
cold (i.e. approximately at ambient
temperature).
To ensure that the tyre pressure monitoring system works reliably, you should
check and, if necessary, adjust the tyre pressures at regular intervals and
store the correct pressures (reference values) in the system.
A tyre pressure information label is attached to the inside of the fuel tank flap.
WARNING
•
Never adjust tyre pressure when the tyres are hot. This may damage or
even burst the tyres. Risk of accident!
•
An insufficiently inflated tyre flexes a lot more at high speeds and
causes significant heating of the ty re. Under these conditions, the tyre
bead may be released or the tyre may burst. Risk of accident!For the sake of the environment
Under-inflated tyres lead to increased fuel consumption and tyre wear.
Note
•
Responsibility for ensuring that the tyres are correctly inflated remains
with the driver; the system can only provide assistance.
•
Pressure can only be adjusted when the tyres are at ambient
temperature.
Cursor
Function selected
Red background (active
function)

Tick
Selected

Box
Not selected

Triangle pointing upwards
Previous page

Triangle pointing down-
wards
Next page
Reset
Exeo_EN.book Seite 88 Freitag, 17. Oktober 2008 11:24 11

Cockpit89
Safety First
Operating instructions
Practical tips
Te c h n i c a l D a t a
Tyre pressure monitoring display

The tyre pressure should be corrected as soon as possible if
it is too low.If the
 symbol appears, the tyre pre ssure on at least one of the
wheels is too low.
– Stop the vehicle.
– Check the tyre(s).
– Correct the tyre pressure ⇒page 228.
For more detailed information on the tyre pressure monitoring system, please
refer to ⇒page 227.
Exeo_EN.book Seite 89 Freitag, 17. Oktober 2008 11:24 11

Steering wheel controls
90Steering wheel controlsThe multi-function steering wheelIntroduction
You can use the multi-function steering wheel to quickly and
easily operate selected functi ons of the radio, CD, TV* and
telephone*.
The functions are operated by pressing or scrolling the controls to on
the multi-function steering wheel ⇒ fig. 63:•
Press the button repeatedly to switch between modes, which
are then displayed in the driver information system ⇒fig. 64 .
•
Scroll and press the left thumbwheel to select a function from one of
the menus.
•
The speech control system* for the on-board phone system is enabled by
pressing the talk button . Pressing th e talk button again disables speed
control*.
•
Scroll the right thumbwheel up/down to raise/lower the volume as
desired.
Fig. 63 Controls on the
multi-function steering
wheel
Fig. 64 Driver informa-
tion system
AA
AD
MODE
AB
AA
AC
AD
Exeo_EN.book Seite 90 Freitag, 17. Oktober 2008 11:24 11

Unlocking and locking95
Safety First
Operating instructions
Practical tips
Te c h n i c a l D a t a
Replacing the key batteryWe recommend you have the batteries changed in a specialist
garage. If you decide to change the used battery yourself, follow the
steps below:
–Carefully prise apart the key ⇒fig. 68 and the cover
using a coin.
– Remove cover in the direction of the arrow.
– Remove the used battery from the cover.
– Insert the new battery. Make sure that the “+” symbol on the battery is facing downwards. The correct polarity is indicated on
the cover.
– After inserting the battery, align the cover and key and press the two parts together. For the sake of the environment
Used batteries must be disposed of appropriately and must not be discarded
with ordinary household waste.
Note
•
The system must be re-synchronised after each battery replacement to be
able to lock and unlock the car using the remote control ⇒page 103.
•
The new battery must be of the same type as the original.
Electronic immobiliser
The electronic immobiliser is designed to prevent unauthor-
ised persons from starting up the vehicle.There is an electronic chip inside th e key which automatically deactivates the
immobiliser when the key is inserted into the ignition lock. The electronic
immobiliser is enabled automatically when the ignition key is removed from
the ignition lock after coming to a stop.
If an uncoded key is used, the message SAFE will appear in the trip recorder
display.
Note
•
The engine can only be started using an original SEAT key with the correct
code.
•
It may not be possible to start the engine with the key if there is another
ignition key from a different make of vehicle on the same key tab.
Fig. 68 Master key:
Opening the cover
AA
AB
Exeo_EN.book Seite 95 Freitag, 17. Oktober 2008 11:24 11