2008 Seat Exeo ignition

Cockpit
68Entire brake system fault
If the ABS warning lamp
 lights up together with the brake warning lamp
 ⇒ page 70 (with the handbrake released), this indicates not only a fault
in the ABS function, but probably also a malfunction in the main brake system
as well ⇒ .
The symbol
 will light up in the instrument panel if a fault occurs in the
brake system . Please refer to ⇒ page 77.
Electronic differential lock (EDL) fault
The EDL works in conjunction with the ABS. The ABS indicator lamp will light
up
 to indicate an EDL fault. Please take the vehicle to a specialist garage
as soon as possible. For further information on the EDL ⇒page 177.WARNING
•
Before opening the bonnet and checki ng the brake fluid level, observe
the warning information in ⇒ page 213, “Work in the engine compart-
ment”.
•
If the brake warning lamp
 should light up together with the ABS
warning lamp
, stop the vehicle immediately and check the brake fluid
level in the reservoir. If the fluid level has dropped below the "MIN" mark
you must not drive on otherwise ther e may be an increased accident risk.
Obtain technical assistance.
•
If the brake fluid level is correct, the fault in the brake system may have
been caused by a fault in the ABS control function. As a result, the rear
wheels can lock relatively easily when braking. Under certain circum-
stances, the rear of the vehicle could suddenly sway from side to side, with
the subsequent danger of skidding. Drive carefully to the nearest specialist
garage and have the fault rectified.
Seat belt warning lamp*

The warning lamp acts as a reminder to the driver to fasten
the seat belt.After switching on the ignition, the warning lamp
 will remain lit until the
driver and front passenger (if applicable) have fastened their seat belts.
When the vehicle has reached a certain speed, you will also hear a warning
signal and the warning light will flash.
For further information on the seat belts, see ⇒page 22.
Indicators and hazard warning lights
 
Depending on which turn signal is operated, either the left
 or right
 indi-
cator lamp flashes. Both indicator lamp s will flash when the hazard warning
lights are switched on.
If one turn signal fails, the indicator lamp will start flashing twice as fast as
normal.
This does not apply when towing a trailer. Where a turn signal lamp does not
work, either on the trailer or on the towing vehicle, the indicator lamp will not
flash. For further informatio n on the indicators, see ⇒page 119.
Electronic stabilisation programme

This warning lamp monitors the electronic stabilisation
program (ESP).The warning lamp
 has the following functions:
Exeo_EN.book Seite 68 Freitag, 17. Oktober 2008 11:24 11

Cockpit69
Safety First
Operating instructions
Practical tips
Te c h n i c a l D a t a
•
It will start flashing to indicate that ESP is counteracting an unstable
driving condition.
•
It lights up when the ignition is switched on for approx. 2 seconds while
the function is checked.
•
The warning lamp will light up if there is a malfunction in the ESP.
•
It will light up after the battery has been disconnected.
•
The warning lamp will light up if the ESP is switched off.
•
It will also come on if a fault should occur in the ABS because the ESP
operates in conjunction with the ABS.
If the ESP warning lamp lights up and stays on after the engine is started, this
may mean that the control system has temporarily switched off the ESP. In this
case the ESP can be reactivated by switching the ignition off and then on
again. After this the warning lamp should go out to show that the system is
fully functional.
The warning lamp will light up when the ignition is switched on if the battery
has been disconnected and then reconnected. It should go out again after
driving a short distance if the steering wheel is turned slightly.
For further information on the ESP, see ⇒ page 177.
Alternator

The warning lamp signals a fault in the alternator or in the
vehicle's electrical system.The warning lamp
 lights up when the ignition is switched on. It should
switch off after the engine has started.
If the warning lamp  lights up when you are driving, you can normally
continue as far as the nearest specialist garage. However, given that the
battery will be running down, any electr ical consumption not absolutely vital
should be switched off.
Caution
If the coolant warning lamp
 in the instrument panel lig h t s u p a s w e l l a s t h e
alternator waning lamp while driving ⇒page 77, stop the vehicle immedi-
ately and switch off the engine. In this case the coolant pump is no longer
being driven, and there is a risk of engine damage.
Main beam headlights

The indicator lamp
 lights up when the main beams are on or when the
headlight flasher is operated.
For further information on the main beam headlights, see ⇒page 119.
Engine management

This warning lamp monitors the engine management system
for petrol engines.The warning lamp
 (Electronic Power Control) li ghts up while the function
is being checked.
Note
If the warning lamp lights up while the vehicle is moving, this indicates a fault
in the engine management system. The vehicle must be taken immediately to
a specialist garage to have the engine serviced.
Exeo_EN.book Seite 69 Freitag, 17. Oktober 2008 11:24 11

Cockpit
70Glow plug system

The indicator lamp lights up while the glow plugs are
preheating.The indicator lamp
 lights up while the glow plugs are preheating. When
the indicator lamp goes out the engine should be started straight away. When
the engine is warm, or at outside temperatures above +8°C, the indicator
lamp will only light up very briefly.
Note
•
If the glow plug indicator lamp should start flashing while the vehicle is
moving, this indicates a fault in the engine management system. The engine
should be serviced without delay.
•
If the indicator lamp fails to light up when the ignition is switched on, this
can mean that the glow plug system is defective. The engine should be
serviced.
Brake system

The warning lamp flashes when the handbrake is applied, or
if the brake fluid level is too low or if there is a fault in the ABS
system.If the warning lamp
 flashes (and the handbrake is not applied), stop the
vehicle and check the brake fluid level ⇒ ⇒ page 222.
If a failure should occur in the ABS, the ABS warning lamp
 will light up
together with the brake warning lamp
 ⇒ . Handbrake applied
The warning lamp
 also lights up when the handbrake is applied. In addi-
tion to this, the handbrake warning ⇒page 76 switches on after driving for 3
seconds at a speed above 5 km/h.
WARNING
•
Before opening the bonnet and checking the brake fluid level, observe
the warning information in ⇒ page 213, “Work in the engine compart-
ment”.
•
If the brake warning lamp does not go out, or if it lights up when
driving, the brake fluid level in the reservoir is too low and this may cause
an increased accident risk. Stop the vehicle and do not drive on. Obtain
technical assistance.
•
If the brake warning lamp lights up together with the ABS warning
lamp, this can mean that the control funct ion of the ABS is out of action. As
a result, the rear wheels can lock relatively easily when braking. Under
certain circumstances, the rear of the vehicle could suddenly sway from
side to side, with the subsequent danger of skidding. Drive carefully to the
nearest specialist garage and have the fault rectified.
Exeo_EN.book Seite 70 Freitag, 17. Oktober 2008 11:24 11

Cockpit
72CD and radio displayIf the radio is switched on and no Priority 2 faults are indicated by the auto-
check control, the “OK” symbol will go out and the display will show the name
or frequency of the selected radio station and various other information,
depending on the type of radio fitted.
When in CD mode*, the display will show the current track.
These displays appear in addition to the display on the radio itself.
Ambient temperature displayThe ambient temperature is shown in the display when the ignition is
switched on ⇒fig. 49.
At temperatures below +5°C a snowflake symbol appears next to the temper-
ature display. This is to warn the driver to take extra care when there is a risk
of ice on the road. When the vehicle is stationary or travelling at very low
speeds, the temperature displayed may be slightly higher than the actual
ambient temperature as a result of heat coming from the engine.
If the vehicle has an air conditioning and the display is changed over to °F
(degrees Fahrenheit), the ambient temperature display automatically
changes over to °F ⇒ page 157.
WARNING
Do not rely on the ambient temperature display as an ice warning. Please
bear in mind that there may be ice on the roads even at ambient tempera-
tures of +5°C – beware of ice patches.
Fig. 48 Display: addi-
tional radio information
Fig. 49 Display: Ambient
temperature display
Exeo_EN.book Seite 72 Freitag, 17. Oktober 2008 11:24 11

Cockpit73
Safety First
Operating instructions
Practical tips
Te c h n i c a l D a t a
Note
When the display shows route guidance instructions from the navigation
system, the ambient temperature appears in the second line of the radio
display.Fuel range
The fuel range display can help you to plan your trip.The estimated fuel range is displayed in km. It shows how far the vehicle can
be driven with the amount of fuel left in the tank, assuming the same style of
driving. The fuel range is displayed in increments of 10 km.
The fuel range is calculated on the basis of the fuel consumption over the last
30 kilometres. The fuel range will increase if you drive in a more economical
manner.
Door catch/ tailgate warningThe door catch/tailgate warning symbol lights up if one or more of the doors,
or the bonnet or tailgate are not proper ly closed when the ignition is on. The
symbol also indicates which of these is not properly closed. The display in the
illustration ⇒fig. 50 shows that the front left door is open.
The corresponding part of the pictogram wil l flash if either the bonnet or tail-
gate are open. The warning symbol goes out when the bonnet, tailgate and
all the doors are closed.
On vehicles with a driver information system and an on-board computer* the
door catches/tailgate warning symbol can be switched off by briefly pressing
one of the control switches for the on-board computer ⇒page 85. However,
the warning symbol will appear again if any of the doors or the bonnet or tail-
gate is opened or closed.
Fig. 50 Display: door
catch/tailgate warning
Exeo_EN.book Seite 73 Freitag, 17. Oktober 2008 11:24 11

Cockpit
74Service indicator
This display reminds the driver when the next routine service
is due.Displaying distance to next service
When you press the service button briefly with the ignition switched on,
the display will show how far the vehicle can be driven before the next service
is due. The query can be made with the engine switched off or in gear up to
speeds of 5 km/h. Every time the igni tion is switched on, the remaining
distance is updated. However, the first time this will be after 500 km.
In new vehicles or following a service, the following display is given for the
first 500 km when the remaining distance until the next service is consulted:
Service reminder
The instrument pane l controls the distance trav elled every day. Calculate the
average of these distances travelled and enable the service reminder suffi-
ciently in advance. The display reverts back to the standard display after about 5 seconds. The
remaining distance to the next service is updated every time the ignition is
switched on, until the service becomes due.
Service due
When a service is due,
SERVICE! will appear in the display immediately after
you switch on the ignition. The display reverts back to the standard display
after about 5 seconds.
Resetting the display
The display is reset by the garage after the service has been carried out. If the
service indicator has not been reset by the specialist garage, please perform
the following steps:
•
Switch the ignition off.
•
Press the service button ⇒fig. 51 and hold while switching on the
ignition. The display will show one of these messages: Service in ----- km or
Service!
•
Now press and hold the reset button until the display shows Service
in ----- km --- days or Service!
The display switches out of the reset mode if you do not press the reset button
within 5 seconds.Note
•
Do not reset the service indicator between services, otherwise the display
will be incorrect.
•
The information in the service indicator remains intact if the battery is
disconnected.
•
The distance to the next service cannot be called up if the system has
detected a Priority 1 fault (red symbol).
Fig. 51 Detailed view of
the instrument panel:
Service indicator
A1
A1A2
Exeo_EN.book Seite 74 Freitag, 17. Oktober 2008 11:24 11

Cockpit75
Safety First
Operating instructions
Practical tips
Te c h n i c a l D a t a
Auto-check systemIntroductionThe auto-check system checks important components and vehicle systems.
These background checks are run consta ntly, as long as the ignition is
switched on.
A message is displayed in the instrument panel if a fault should occur or if any
maintenance or repairs are urgently required. This is accompanied by an
audible warning signal. Depending on the pr iority of the fault, a red or yellow
warning symbol lights up in the display.
The red symbols indicate a danger, whereas the yellow ones represent a
warning . Additional messages to assist the driver may be shown with the red
or yellow symbols.
Driver messages
Additional messages to assist the driver are displayed
together with the warning symbols in the instrument panel.Driver messages and red symbols
If a red warning symbol appears in the display, you can press the
button ⇒fig. 52 to call up an additional driver message.
For example: in the event of an oil pressure malfunction, the oil pressure
symbol

will appear in the display. If you now press the button, the
following message will appear in the display:
Switch off engine, check oil level
The message will disappear from the display after about 5 seconds. If
required, the message can be called up again by briefly pressing the
button.
Fig. 52 Instrument panel:
CHECK button
CHECK
CHECK
CHECK
Exeo_EN.book Seite 75 Freitag, 17. Oktober 2008 11:24 11

Cockpit81
Safety First
Operating instructions
Practical tips
Te c h n i c a l D a t a
Bulb monitor

The bulb monitor checks whether the lights on the vehicle are
working.If a defective bulb is detected, or if one of the lights has failed for any reason,
the bulb monitor symbol
 will appear in the display together with an addi-
tional message (which goes out after 5 sec onds). For instance, if the rear left
turn signal is not working, the display in the instrument panel will show the
following message:
Left rear turn signal
The message disappears after 5 seconds. Press the CHECK button briefly if
you wish to call up the message again.
If the display indicates that one of the lights is not working, this can have a
number of causes:
•
Bulb failure ⇒page 249.
•
A “blown” fuse ⇒page 247, “Changing fuses”.
•
Faulty electrical wiring.
Have the components replaced or the wiring repaired as necessary by a
specialist garage.
WARNING
•
Bulbs are highly sensitive to pressure. The glass can break when you
touch the bulb, causing injury.
•
The high voltage element of gas discharge lamps* (xenon light) must
be handled correctly. Otherwise, there is a risk of death.
Speed warning

Introduction
The speed warning function can help prevent you exceeding
a particular pre-set maximum speed.The speed warning function will warn the driver if a pre-set maximum speed
is exceeded. The system gives an audible warning signal if the set speed is
exceeded by about 10 km/h. A warning symbol will also appear in the display
⇒ fig. 55 .
The speed warning function has two different warning speeds, which operate
independently and serve slightly different purposes:
Speed limit warning 1

With speed limit warning 1, the maximum speed can be changed while
driving. The speed limit that has been set remains stored until the ignition is
switched off, or until it is changed or cleared.
Fig. 55 Display: Speed
warning function
Exeo_EN.book Seite 81 Freitag, 17. Oktober 2008 11:24 11