2008 Seat Cordoba wheel bolt torque

Seats and stowage115
Safety First
Operating instructions
Tips and Maintenance
Te c h n i c a l D a t a
WARNING
Do not place heavy or hard objects on the luggage compartment cover, this
will endanger the vehicle occupants in case of sudden braking.
Caution
•
Before closing the tailgate, ensure that the stowage compartment tray is
correctly fitted.
•
An overloaded boot could mean that the rear stowage tray is not correctly
seated and it may be bent or damaged.Note
•
Below the boot floor trim, next to the spare wheel, is a removable stowage
tray.
Roof carrier*Please observe the following points if you intend to carry loads on the roof:•
For safety reasons, only luggage racks and accessories approved by SEAT
should be used.
•
It is imperative to precisely follow the fitting instructions included for the
rack, taking special care when fitting the front bar in the holes designed for
this and the rear bar between the marks on the upper part of the rear door
frame while respecting the correct direction of travel indicated in the installa-
tion manual. Not following these instructions may lead to paintwork damage
or marks on the bodywork.
•
Pay special attention to the tightening torque of the attachment bolts and
check them following a short journey. If necessary, retighten the bolts and
check them at regular intervals.
•
Distribute the load evenly. A maximum load of 40 kg only is permitted for
each roof carrier system support bar, the load must be distributed evenly over
the entire length. However, the maximum load permitted for the entire roof
(including the support system) of 75 kg must not be exceeded nor should the
total weight of the vehicle be exceeded. See the chapter on “Technical Data”.
•
When transporting heavy or large objects on the roof, any change in the
normal vehicle behaviour due to a change in the centre of gravity or an
increased wind resistance must be taken into account. For this reason, a suit-
able speed and driving style must be used.
•
For those vehicles fitted with a sunroof*, ensure that it does not interfere
with the load on the roof carrier system when opened.
COR_ING_0707 Seite 115 Mittwoch, 1. August 2007 6:25 18

Checking and refilling levels
194•
Avoid running the vehicle on tyres that are more than six years old. If
you have no alternative, you should dr ive slowly and with extra care at all
times.
•
Never use old tyres or those with an unknown “history of use”.
•
If wheel trims are retrofitted, you must ensure that the flow of air to the
brakes is not restricted. This could cause them to overheat.
•
All four wheels must be fitted with radial tyres of the same type, size
(rolling circumference) and the same tread pattern.For the sake of the environment
Old tyres must be disposed of according to the laws in the country concerned.
Note
•
For technical reasons, it is not generally possible to use the wheels from
other vehicles. This can also apply to wheels of the same model. The use of
wheels or tyres which have not been approved by SEAT for use with your
model may invalidate the vehicle's type approval for use on public roads.
•
If the spare tyre is not the same as the tyres that are mounted on the
vehicle - for example with winter tyres - you should only use the spare tyre for
a short period of time and drive with extra care. Refit the normal road wheel
as soon as possible.
Wheel bolts
Wheel bolts must be tightened to the correct torque.The design of wheel bolts is matched to the rims. If different wheel rims are
fitted, the correct wheel bolts with the right length and correctly shaped bolt heads must be used. This ensures that wheels are fitted securely and that the
brake system functions correctly.
In certain circumstances, you may not use wheel bolts from a different car -
even if it is the same model
⇒page 167.
WARNING
If the wheel bolts are not tightened correctly, the wheel could become
loose while driving. Risk of accident.•
The wheel bolts must be clean and turn easily. Never apply grease or oil
to them.
•
Use only wheel bolts which belong to the wheel.
•
If the prescribed torque of the wheel bolts is too low, they could loosen
whilst the vehicle is in motion. Risk of accident! If the tightening torque is
too high, the wheel bolts and threads could be damaged.Caution
The prescribed torque for wheel bolts for steel and alloy wheels is 120 Nm.Winter tyres
Winter tyres will improve the vehicles handling on snow and
ice.In winter conditions winter tyres will considerably improve the vehicles
handling. The design of summer ty res (width, rubber compound, tread
pattern) gives less grip on ice and snow.
Winter tyres must be inflated to a pressure 0.2 bar higher than the pressures
specified for summer tyres (see sticker on tank flap).
Winter tyres must be fitted on all four wheels.
WARNING (continued)
COR_ING_0707 Seite 194 Mittwoch, 1. August 2007 6:25 18

If and when
196If and whenVehicle tools, spare wheelVehicle To ols
The vehicle onboard tools are located under the floor panel in
the luggage compartment.– Lift floor panel
– Remove the tools or jack.The tool kit includes:•
Jack*
•
Hook for removing wheel covers or hub caps*
•
Box spanner for wheel bolts*
•
Reversible screwdriver with handle (including hexagonal interior) for the
wheel bolts. The screwdriver is a combination tool.
•
To wi ng e ye
•
Adapter for the anti-theft wheel bolts*
Some of the items listed are only prov ided in certain models / model years,
or are optional extras.
WARNING
•
Do not use the hexagonal socket in the screwdriver handle to tighten
the wheel bolts as with this it is not possible to tighten the bolts to the
required torque, risk of accident.
•
The jack supplied by the factory is only designed for changing wheels
on this model. On no account attempt to use it for lifting heavier vehicles
or other loads, risk of injury.
•
Use the jack only on firm, level ground.
•
Never start the engine when the vehicle is on the jack, risk of accident.
•
I f wo r k is t o b e ca r r i e d o u t un d e r n ea th the vehicle, this must be secured
by suitable stands. Otherwise, there is a risk of injury.
Compact temporary spare wheel*
If provided as part of the vehicle's equipment, the compact
temporary spare wheel is only intended for temporary use
over short distances.The temporary spare wheel is stored under the floor panel in the luggage
compartment and is attached by a thumbnut.
How to use the compact temporary spare wheel
Should you ever have a punctured tyre, the compact temporary spare wheel
is only intended for temporary use until you can reach a workshop. The
standard-size road wheel should be replaced as soon as possible.
Please note the following restrictions when using the compact temporary
spare wheel. This spare wheel has been specially designed for your vehicle,
thus, it cannot be changed with the spare wheel from another vehicle.
No other type of tyre (normal summer or winter tyre) may be fitted on the
compact temporary spare wheel rim.
WARNING (continued)
COR_ING_0707 Seite 196 Mittwoch, 1. August 2007 6:25 18

If and when
198
WARNING
Put the hazard warning lights on and pl ace the warning triangle in position.
This is for your own safety and also warns other road users.
Caution
If you have to change the tyre on a gradient, block the wheel opposite the
wheel being changed by placing a stone or similar object under it to prevent
the vehicle from rolling away.
Note
Please observe legal requirements when doing so.Changing a wheelChange the wheel as described below
– Remove the hub cap. Also refer to ⇒page 199.
–Slacken the wheel bolts.
– Raise the car with the jack in the corresponding zone.
– Ta k e o f f the wheel and then put on the spare wheel.
– Lower the vehicle.
– Tighten the wheel bolts firmly i n d ia go na l s e q u e n ce wi t h t h e b ox
spanner.
–Replace the hub cap.
After changing a wheel
After changing the wheel there are still tasks to complete.– Put the tools and jack back in the luggage compartment.
– Place the wheel with the defective tyre in the luggage compart- ment and secure it.
– Check the tyre pressure of the newly fitted tyre as soon as possible.
– Have the tightening torque of the wheel bolts checked as soon as possible with a torque wrench. The prescribed torque is 120 Nm.
Note•
If you notice that the wheel bolts are corroded and difficult to turn when
changing a wheel, they must be replaced before having the wheel bolt torque
checked.
•
In the interest of safety, drive at moderate speeds until the wheel bolt
torque has been checked.
COR_ING_0707 Seite 198 Mittwoch, 1. August 2007 6:25 18

General notes on the technical data 231
Safety First
Operating instructions
Tips and Maintenance
Te c h n i c a l D a t a
Snow chains
Snow chains are only permitted on the front wheels and only for tyres 155/80
R13; 165/70 R14 and 185/80 R14. Snow ch
ains must have fine-pitch links
which do not protrude more than 15 mm, including tension device.
Remaining tyres can be fitted with chains no thicker than 9 mm.
Wheel bolts
After the wheels have been changed, the tightening torque of the wheel bolts
should be checked as soon as possible with a torque wrench ⇒. The tight-
ening torque for steel and alloy wheels is 120 Nm.
WARNING
•
Check the tyre pressure at least once per month. Correct tyre pressure
is very important. If the tyre pressure is too high or too low, there is an
increased danger of accidents, particularly at high speeds.
•
If the torque of the wheel bolts is too low, they could loosen whilst the
vehicle is in motion. Risk of accident! If the tightening torque is too high,
the wheel bolts and threads could be damaged.Note
We recommend that you ask your Authorised Service Centre for information
about appropriate wheel, tyre and snow chain size.
COR_ING_0707 Seite 231 Mittwoch, 1. August 2007 6:25 18

Index253
Switch
Hazard warning lights . . . . . . . . . . . . . . . . . . 91
Rear window heating . . . . . . . . . . . . . . . . . . . 90
Switches Electric windows . . . . . . . . . . . . . . . . . . . . . . 84
Sliding/tilting roof . . . . . . . . . . . . . . . . . . . . . 87
Switching off the engine . . . . . . . . . . . . . . . . . . 132TTailgate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Tank fuel level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
reserve indicator . . . . . . . . . . . . . . . . . . . . . . 54
tank capacity . . . . . . . . . . . . . . . . . . . . . . . . . 54
TCS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
TCS (Traction control system) Warning lamp . . . . . . . . . . . . . . . . . . . . . . . . . 66
The danger of not using the seat belt . . . . . . . . 19
Tightening torque of wheel bolts . . . . . . . . . . . 231
Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 196
Towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 224
Towing a trailer . . . . . . . . . . . . . . . . . . . . 154, 230
Towing bracket . . . . . . . . . . . . . . . . . . . . . . . . . . 155
Towing bracket, fitting . . . . . . . . . . . . . . . . . . . 170
Towing eye . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 224
Tow-starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 224
Traction control system warning lamp . . . . . . . . . . . . . . . . . . . . . . . . . 66 Trailer turn signals
Indicator lamps . . . . . . . . . . . . . . . . . . . . . . . 67
Warning lamp . . . . . . . . . . . . . . . . . . . . . . . . . 93
Trailer weights . . . . . . . . . . . . . . . . . . . . . . . . . . 230
Trips, checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Turn signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92 Warning lamp . . . . . . . . . . . . . . . . . . . . . . 63, 93
Two-way radio . . . . . . . . . . . . . . . . . . . . . . . . . . 168
Type plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 228
Tyre Mobility-System (Tyre repair kit) . . . 197, 203
Tyre pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . 191
Tyre pressures . . . . . . . . . . . . . . . . . . . . . . . . . . 230
Tyre repair kit . . . . . . . . . . . . . . . . . . . . . . 197, 203
Tyres and wheels Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . 193
Tyres service life . . . . . . . . . . . . . . . . . . . . . . . . 192
Tyres tread depth . . . . . . . . . . . . . . . . . . . . . . . . 192
Tyres with directional tread pattern . . . . . . . . . 191
UUnderbody sealant . . . . . . . . . . . . . . . . . . . . . . 163
USB* connection . . . . . . . . . . . . . . . . . . . . . . . . 113VVehicle battery . . . . . . . . . . . . . . . . . . . . . . . . . . 188
Vehicle data . . . . . . . . . . . . . . . . . . . . . . . . . . . . 228
Vehicle identification data . . . . . . . . . . . . . . . . 228
Vehicle identification number . . . . . . . . . . . . . 228
Vehicle interior heating or cooling system . . . 120 Vehicle paint
Car care products . . . . . . . . . . . . . . . . . . . . 158
Vehicle tools Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 196
Vehicle wallet storage . . . . . . . . . . . . . . . . . . . . 108
Ventilation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
Ventilation slits . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Volumetric sensor* Activation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Deactivation . . . . . . . . . . . . . . . . . . . . . . . . . . 81
WWarning lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Warning lamps . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Warning triangles . . . . . . . . . . . . . . . . . . . . . . . 113
Washer fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185
Washing by hand . . . . . . . . . . . . . . . . . . . . . . . . 159
Washing the vehicle . . . . . . . . . . . . . . . . . . . . . 159
Washing with high pressure cleaners . . . . . . . 160
Water in the windscreen washer tank . . . . . . . 185
Wear indicators . . . . . . . . . . . . . . . . . . . . . . . . . 192
Wheel bolts . . . . . . . . . . . . . . . . . . . . . . . 200, 231Torque . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 194
Wheel change . . . . . . . . . . . . . . . . . . . . . . . . . . 197
Wheel trims . . . . . . . . . . . . . . . . . . . . . . . . . . . . 199
Wheels . . . . . . . . . . . . . . . . . . . . . . . . . . . 190, 230
Why assume the correct sitting position? . . . . . 27
Why should head restraints be correctly adjusted? 12
COR_ING_0707 Seite 253 Mittwoch, 1. August 2007 6:25 18