2008 Seat Altea Freetrack mileage

Cockpit59
Safety First
Operating instructions
Tips and Maintenance
Te c h n i c a l D a t a
Digital display in the instrument panelDisplay (without warning or information texts)
The display in the instrument panel shows, amongst other
things, the mileage and trip recorder as well as the selector
lever position.
Digital clock display ⇒page 58
Distance display or service interval display ⇒page 60
Selector lever position display for the automatic gearbox*.
Display for the gears in Tiptronic mode (automatic gearbox)*. The
selected gear appears in the display field with a light background
⇒ fig. 37 .
Fig. 36 Detail of the
instrument cluster: screen
with different indicators
Fig. 37 Detail of the
instrument cluster: screen
with Tiptronic gear indi-
cator
A1A2A3A4
altea_XL ingles.book Seite 59 Donnerstag, 13. September 2007 10:36 10

Cockpit
60Displayed categories
The display in the instrument panel shows the mileage and
trip recorder as well as the selector lever position.
Warning and monitoring indicators: “Warning and indication lamps”
Clock: “Setting the time”. In some vehicles the ambient temperature is
displayed to the right of the clock.
There are optional and automatic displays in this field.
- Optional indicators: e.g. Multi-function display (MFD) and ambient
temperature display
- Automatic indicators: Information texts and warnings: “Warning and
information messages on the screen”
- Menus providing further information and which can be used to make diverse settings are also shown: “Instrument panel menus” Distance display or flexible service interval display: “Distance display or
flexible service interval display”
Selector lever position display for the automatic gearbox. The actual
position of the selector lever or the gear which is engaged (for Tiptronic)
are highlighted.
Mileage display or Service Interval DisplayDistance display
The left-hand counter in the display registers the total amount of distance
covered by the vehicle.
The right-hand counter regi
sters the short journeys. The last digit indicates
steps of 100 metres. The trip recorder counter may be reset by the reset
button ⇒page 56, fig. 33 .
Service interval display
A service pre-warning will appear on the mileage displays if a service is due
soon. A “spanner” symbol appears and the display “miles” with the distance
that can be driven until the next service appointment is due. The display will
change after approximately 10 seconds. A “clock symbol” appears and the
number of days until the service appointment should be carried out. The
instrument panel displays shows the following message
5): SERV. IN ... KM OR
... DAYS . The service message will disappear approximately 20 seconds after
the ignition is switched on or the en gine is running. The normal display can
be resumed by pressing the reset button on the trip counter or by pressing the
rocker switch of the MFI ⇒page 61, fig. 39 .
With the ignition switched on, you can call up the current service message by
pressing the trip counter reset knob for 2 seconds.
Fig. 38 Digital display in
the instrument panel
A1A1A2
5)Depending on the model versionA3A4
A5
AB
altea_XL ingles.book Seite 60 Donnerstag, 13. September 2007 10:36 10

Cockpit61
Safety First
Operating instructions
Tips and Maintenance
Te c h n i c a l D a t a
An
overdue service is indicated by a minus sign in front of the mileage or day
information.
Display with multi-function display (MFD)*
The multi-function display (M FD) shows you diverse journey
and consumption data.
The multi-function system uses two automatic memories: 1 - Trip
memory and 2 - Total memory . The selected memory will be shown
in the upper right-hand corner of the display.
Selecting memory
– With the ignition switched on, briefly press the button ⇒fig. 39
on the windscreen wiper lever to move between the two
memories.
Resetting the memory
– Select the memory that you would like to reset.
– Press and hold button on the windscreen wiper lever for at least 2 seconds.The trip memory 1 collects the travel and cons umption data from the moment
the ignition is switched on until it is switched off. If the journey is continued
within two hours of switching off the ignition, the new values will be added to
Fig. 39 Windscreen wiper
and windscreen wash
lever: button A and rocker
switch B
Fig. 40 Digital instru-
ment panel display:
average fuel consumption
indicator
AA
AA
altea_XL ingles.book Seite 61 Donnerstag, 13. September 2007 10:36 10

Intelligent technology
186occurs - without warning to the driver - in regular intervals and requires a
more rapid response from the brakes when driving on wet roads.
In certain conditions, such as in heavy rain, or after washing the car or driving
through water, the full braking effect ca n be delayed by moisture (or in winter
by ice) on the discs and brake pads. The brakes should be dried by pressing
the pedal to restore full braking effect.
The effectiveness of the brakes can also be temporarily reduced if the car is
driven for some distance without using the brakes when there is a lot of salt
on the road in winter. In this case, the layer of salt on the brake discs and pads
has to wear off before braking.
Corrosion
There may be a tendency for dirt to build up on the brake pads and corrosion
to form on the discs if the car is used infrequently, or if you only drive low
mileages without using the brakes very much.
If the brakes are not used frequently, or if corrosion has formed on the discs,
it is advisable to clean off the pads and discs by braking firmly a few times
from a moderately high speed ⇒.
Faults in the brake system
If the brake pedal travel should ever increase suddenly, this may mean that
one of the two brake circuits has failed. Drive immediately to the nearest qual-
ified workshop and have the fault rectified. On the way to the dealer, be
prepared to use more pressure on the brake pedal, and allow for longer stop-
ping distances.
Low brake fluid level
Malfunctions can occur in the brake system if the brake fluid level is too low.
The brake fluid level is monitored electronically.
Brake servo
The brake servo amplifies the pressure you apply to the brake pedal. The
brake servo works only when the engine is running.
WARNING
•
When applying the brakes to clean off deposits on the pads and discs,
select a clear, dry road. Be sure not to inconvenience or endanger other
road users. Risk of accident.
•
Ensure the vehicle does not move wh ile in neutral, when the motor is
stopped. Failure to do so could result in an accident.Caution
•
Never let the brakes “drag” by leaving your foot on the pedal when you do
not really intend to brake. This overh eats the brakes, resulting in longer stop-
ping distances and greater wear.
•
Before driving down a long, steep gradient, it is advisable to reduce speed
and change to a lower gear (or move the selector lever to a lower gear position
if your car has automatic transmission). This makes use of engine braking
and prolongs the service life of the brakes. If you still have to use the brakes,
it is better to brake firmly at interval s than to apply the brakes continuously.Note
•
If the brake servo is not functioning due to a malfunction, or if the vehicle
has to be towed, you will have to press the brake pedal considerably harder
to make up for the lack of servo assistance.
•
If you wish to equip the car with accessories such as a front spoiler or
wheel covers, it is important that the flow of air to the front wheels is not
obstructed, otherwise the brakes can overheat.
altea_XL ingles.book Seite 186 Donnerstag, 13. September 2007 10:36 10

Driving and the environment
194On the right hand side headlight, if you are changing from driving on the
right-hand side to the left-hand side ⇒page 193, fig. 158.
On the left hand side headlight, if you are changing from driving on the left-
hand side to the right-hand side ⇒page 193, fig. 159 .Driving economically and with respect for the
environmentGeneral ObservationsFuel consumption, environmental pollution and wear to the engine, brakes
and tyres depends in large part on your driving style. Fuel consumption may
be reduced from 10 to 15 % by driving defensively and economically. Below
we will give you some suggestions to "alleviate" some of the strain in the
environment and, at the same time, your wallet.
Anticipate the traffic situation well in advance
A vehicle uses most fuel when accelerating. When you anticipate the situa-
tion, you will have to brake less often and, thus, accelerate less. If it is
possible, let the vehicle roll with a gear engaged, for example, if you see a red
light ahead.
Change gear early to save energy
An effective way of saving fuel is to change up quickly through the gears.
Running the engine at high rpm in the lower gears uses an unnecessary
amount of fuel.
Manual gearbox: Change from first to second gear as quickly as possible. We
recommend that, whenever possible, you change to a higher gear upon
reaching 2,000 rpms.
Automatic gearbox: Accelerate slowly and avoid the “kick-down” position. Avoid driving at high speed
We advise you not to drive at the top speed permitted by the vehicle. Fuel
consumption, exhaust emissions and noise levels all increase very rapidly at
higher speeds. Driving at moderate speeds will help to save fuel.
Avoid idling
It is worthwhile switching off the engine when waiting in a traffic jam, at level
crossings or at traffic lights with a long red phase. The fuel saved after only
30 - 40 seconds is greater than the amount of fuel needed to restart the
engine.
The engine takes a very long time to
warm up when it is running at idling
speed. Mechanical wear and pollutant emissions are also especially high
during this initial warm-up phase. It is therefore best to drive off immediately
after starting the engine . Avoid running the engine at high speed.
Periodic maintenance
Periodic maintenance work guarantees that, before beginning a journey, you
will not waste fuel. A well-serviced engine gives you the benefit of improved
fuel efficiency as well as maximum reliability and an enhanced resale value.
A maladjusted engine may mean an increase of 10 % over normal fuel
consumption.
Check the oil level every time you fill the tank. Oil consumption depends to a
great extent on the engine load and engi ne speed. It is quite normal that the
oil consumption of a new engine only reaches its lowest level after a certain
mileage. This means that the oil consumption can only be properly assessed
after about 5,000 km. Depending on your personal driving style, oil consump-
tion can be up to 0.5 litres per 1,000 km.
Avoid short journeys
To reduce the consumption and emission of polluting gases, the engine and
the exhaust filtration systems should reach the optimum service tempera-
ture.
altea_XL ingles.book Seite 194 Donnerstag, 13. September 2007 10:36 10

Checking and refilling levels231
Safety First
Operating instructions
Tips and Maintenance
Te c h n i c a l D a t a
•
If the vehicle is left standing in cold conditions for a long period, protect
the battery from frost. If it “freezes” it will be damaged.
Checking the electrolyte level
The electrolyte level should be checked regularly in high-
mileage vehicles, in hot countries and in older batteries.– Open the bonnet and open the battery cover at the front ⇒ in
“Safety instructions on working in the engine compartment” on
page 215 ⇒ in “Warnings on handling the battery” on
page 230.
– Check the colour display in the "magic eye" on the top of the battery.
– If there are air bubbles in the window, tap the window gently until they disperse.The position of the battery is shown in the corresponding engine compart-
ment diagram ⇒page 279.
The round window (“magic eye”) on the top of the battery changes colour,
depending on the charge level and electrolyte level of the battery.
If the colour in the window is colourless or bright yellow, the electrolyte level
of the battery is too low. Have the battery checked by a qualified workshop.
The colours green and black are used by the workshops for diagnostic
purposes.
Charging and changing the vehicle battery
The battery is maintenance-free and is checked during the
inspection service. All work on the vehicle battery requires
specialist knowledge.If you often drive short distances or if the vehicle is not driven for long
periods, the battery should be checked by a qualified workshop between the
scheduled services.
If the battery has discharged and you have problems starting the vehicle, the
battery might be damaged. If this happens, we recommend you have the
vehicle battery checked by an Authorised Service Centre where it will be re-
charged or replaced.
Charging the battery
The vehicle battery should be charged by a qualified workshop only, as
batteries using special technology have been installed and they must be
charged in a controlled environment.
Replacing a vehicle battery
The battery has been developed to suit the conditions of its location and has
special safety features.
Genuine SEAT batteries fulfil the maintenance, performance and safety spec-
ifications of your vehicle.
WARNING
•
We recommend you use only maintenance-free or cycle free leak-proof
batteries which comply with the standards T 825 06 and VW 7 50 73. This
standard applies as of 2001.
•
Before starting any work on the batteries, you must read and observe
the warnings ⇒ in “Warnings on handling the battery” on page 230.
altea_XL ingles.book Seite 231 Donnerstag, 13. September 2007 10:36 10

Index309
head restraints
Adjusting . . . . . . . . . . . . . . . . . . . . . . 129, 130
adjustment of the head restraint angle . . . 130
Removing . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
head restraints, correct adjustment . . . . . . . . . . 13 In-use and non-use positions . . . . . . . . . . . . 14
Headlight flasher . . . . . . . . . . . . . . . . . . . . . . . . 116
Headlight range control . . . . . . . . . . . . . . . . . . 113
Headlights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111 Driving abroad . . . . . . . . . . . . . . . . . . . . . . . 191
Fog lights . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
Washer system . . . . . . . . . . . . . . . . . . . . . . . 125
Heated front seats . . . . . . . . . . . . . . . . . . . . . . . 132
Heated window 2C-Climatronic . . . . . . . . . . . . . . . . . . . . . . . 157
Heating and ventilation . . . . . . . . . . . . . . . . . . . 151
High pressure cleaners . . . . . . . . . . . . . . . . . . . 203
Horn . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55IIdentification number . . . . . . . . . . . . . . . . . . . . 276
Ignition key . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163
Ignition lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163
Indicator lights indication lamp . . . . . . . . . . . . . . . . . . . . . . . 76
Information texts in the display . . . . . . . . . . . . . 63
Instrument and switch lighting . . . . . . . . . . . . . 113
Instrument lighting . . . . . . . . . . . . . . . . . . . . . . . 55
Instrument panel . . . . . . . . . . . . . . . . . . . . . . . . . 55 Instrument panel menu
Configuration menu . . . . . . . . . . . . . . . . . . . . 69
Example of menu use . . . . . . . . . . . . . . . . . . 67
Lights and visibility menu . . . . . . . . . . . . . . . 71
Instrument panel menus Principal menu . . . . . . . . . . . . . . . . . . . . . . . . 65
Vehicle status menu . . . . . . . . . . . . . . . . . . . 69
Instruments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Interior lights . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
Intermittent wipe, windscreen . . . . . . . . . . . . . 121
ISOFIX and Toptether systems . . . . . . . . . . . . . . 52
JJacking points Sill panel with cover . . . . . . . . . . . . . . . . . . 248
Jump leads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 268
Jump-starting . . . . . . . . . . . . . . . . . . . . . . . . . . . 268KKey tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99LLights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
Load compartment See Luggage compartment . . . . . . . . . . . . . . 17
Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 205 Luggage compartment . . . . . . . . . . . . . . . . 17, 147
See also Luggage compartment . . . . . . . . . . 17
Luggage compartment cover . . . . . . . . . . . . . . 148
Luggage compartment retaining net . . . . . . . . 138
MMain beam . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
Main beam headlights Indicator lamp . . . . . . . . . . . . . . . . . . . . . . . . 76
Main headlight lamps . . . . . . . . . . . . . . . . . . . . 260
Manual gearbox . . . . . . . . . . . . . . . . . . . . . . . . . 167
Manual mode 2C-Climatronic . . . . . . . . . . . . . . . . . . . . . . . 158
MFD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Mileage display . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Mirrors Exterior mirrors, electrical . . . . . . . . . . . . . . 126
Interior mirror . . . . . . . . . . . . . . . . . . . . . . . . 125
Make-up mirrors . . . . . . . . . . . . . . . . . . . . . 120
Mobile telephone . . . . . . . . . . . . . . . . . . . . . . . 211
Modifications . . . . . . . . . . . . . . . . . . . . . . . . . . . 210
Multi-function display . . . . . . . . . . . . . . . . . . . . . 61
Multi-purpose* mobile stowage compartment 141
Closing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141
Fitting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140
Opening . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140
Uses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141
altea_XL ingles.book Seite 309 Donnerstag, 13. September 2007 10:36 10