2008 SATURN VUE HYBRID instrument panel

Increasing Speed While Using Cruise
Control
There are two ways to go to a higher speed.
Disengage the cruise control, but do not turn it off.
If the cruise control system is already engaged,
press the thumbwheel up toward RES+ and hold it
until your vehicle accelerates to the desired speed,
and then release the switch. To increase the speed
in very small amounts, press the thumbwheel up
toward RES+ briey and then release it. Each
time this is done, the vehicle will go about 1 mph
(1.6 km/h) faster.
Reducing Speed While Using Cruise
Control
If the cruise control system is already engaged,
Push the thumbwheel toward−SET and hold
until the desired lower speed is reached, then
release it.
To slow down in very small amounts, push the
thumbwheel toward−SET briey. Each time
this is done, the vehicle goes about 1 mph
(1.6 km/h) slower.
Passing Another Vehicle While Using
Cruise Control
Use the accelerator pedal to increase the vehicle’s
speed. When you take your foot off the pedal, the
vehicle will slow down to the previously set cruise
control speed.
Using Cruise Control on Hills
How well the cruise control works on hills depends upon
the vehicle’s speed, load, and the steepness of the hills.
When going up steep hills, you might have to step on the
accelerator pedal to maintain the vehicle’s speed. When
going downhill, you might have to brake or shift to a lower
gear to maintain the vehicle’s speed. Of course, applying
the brakes ends cruise control. Many drivers nd this to
be too much trouble and do not use cruise control on
steep hills.
Ending Cruise Control
There are three ways to disengage the cruise control:
Step lightly on the brake pedal or clutch; when
cruise control disengages, the indicator light on
the instrument panel cluster goes out.
Press the on/off button, this will turn off the cruise
control system.
3-13
ProCarManuals.com

Erasing Speed Memory
The cruise control set speed memory is erased when
the cruise control or the ignition is turned off.
Exterior Lamps
The exterior lamp control is
located on the instrument
panel to the left of the
steering wheel.
The exterior lamp control can be turned to the following
positions:
9(Off):This position turns off the exterior lamps.
The knob returns to the AUTO position after it is
released.
AUTO (Automatic):This position is the automatic
mode for headlamps. The exterior lamps turn on and
off, depending on outside lighting.
;(Parking Lamps):This position turns on the
parking lamps together with the following:
Sidemarker Lamps
Taillamps
License Plate Lamps
Instrument Panel Lights
2(Headlamps):This position turns on the
headlamps, together with the previously listed lamps
and lights.
Lamps On Reminder
A warning chime sounds, if the driver’s door is opened
while the ignition is off and the lamps are on.
Wiper Activated Headlamps
This feature automatically turns on the headlamps and
parking lamps if the exterior lamp control is set in the
AUTO position and the windshield wipers are turned on
and have completed eight wipe cycles. SeeExterior
Lamps on page 3-14for additional information.
When the ignition is turned off, the wiper-activated
headlamps immediately turn off. They also turn off if
the windshield wiper control is turned off.
3-14
ProCarManuals.com

Daytime Running Lamps (DRL)
Daytime Running Lamps (DRL) can make it easier for
others to see the front of your vehicle during the day.
DRL can be helpful in many different driving conditions,
but they can be especially helpful in the short periods
after dawn and before sunset. Fully functional daytime
running lamps are required on all vehicles rst sold in
Canada.
The DRL system makes the low-beam headlamps come
on in daylight when the following conditions are met:
The engine is running,
The exterior lamp band is in AUTO, and
The light sensor determines it is daytime.
When the DRL are on, the low-beam headlamps will be
on. The taillamps, sidemarker, and other lamps will
not be on. The instrument panel will not be lit up either.
When the exterior lamp band is turned to the headlamp
position, the regular headlamps will come on. The other
lamps that come on with the headlamps will also
come on.
When the headlamps are turned off, the regular lamps
also turn off, and the low-beam headlamps turn on.
The regular headlamp system should be used when
needed.
Automatic Headlamp System
When it is dark enough outside, the headlamps come
on automatically.
There is a light sensor located on top of the instrument
panel. Make sure it is not covered, or the headlamps
will come on when they are not needed.
The system may also turn on the headlamps when
driving through a parking garage or tunnel.
3-15
ProCarManuals.com

Instrument Panel Brightness
This feature controls the brightness of the instrument
panel lights.
The thumbwheel for this
feature is located on the
left side of the steering
wheel next to the exterior
lamps control.
Turn the thumbwheel to the right to brighten the lights
or to the left to dim them.
Dome Lamp
*(Dome Lamp Override):Press this button to keep
the dome lamps and other interior lamps turned off while
any door is open. Press this button again to return it to the
out position and the lamps automatically come on when
any door is opened.
+(On/Off):Press this button to turn the dome
lamps on and off while the doors are closed.
Entry Lighting
If the dome lamp override button is in the out position,
the lamps inside the vehicle automatically come on
when any door is opened or when the Remote Keyless
Entry (RKE) unlock button is pressed. After the door is
opened the lights remain on and stay on for 20 seconds
after the doors are closed, or until the key is put into the
ignition and turned to the ACC/ACCESSORY position.
The lights will then gradually dim until it is no longer lit.
3-16
ProCarManuals.com

Reading Lamps
The reading lamps are located on the overhead console.
To turn the reading lamps on or off, press the button
located next to each lamp.
Battery Run-Down Protection
The battery saver feature is designed to protect your
vehicle’s battery.
If any interior or exterior lamp is left on and the ignition
is turned off, the battery rundown protection system
automatically turns the lamp off after 10 minutes.
Accessory Power Outlet(s)
The accessory power outlets can be used to connect
electrical equipment such as a cellular phone or
CB radio.
The accessory power outlets are located on the rear
of the center storage console and in the rear cargo
compartment. There may be a power outlet located inside
the instrument panel storage area below the climate
controls.To use the outlets, remove the cover. When not in use,
always cover the outlet with the protective cap.
Notice:Leaving electrical equipment on for
extended periods will drain the battery. Always
turn off electrical equipment when not in use and
do not plug in equipment that exceeds the maximum
20 ampere rating.
Certain electrical accessories may not be compatible
with the accessory power outlet and could result in blown
vehicle or adapter fuses. If you experience a problem,
see your dealer/retailer for additional information on the
accessory power outlet.
Notice:Adding any electrical equipment to your
vehicle may damage it or keep other components
from working as they should. The repairs would
not be covered by your warranty. Check with your
dealer/retailer before adding electrical equipment.
When adding electrical equipment, be sure to follow the
installation instructions included with the equipment.
Notice:Improper use of the power outlet can cause
damage not covered by your warranty. Do not
hang any type of accessory or accessory bracket
from the plug because the power outlets are
designed for accessory power plugs only.
3-17
ProCarManuals.com

Climate Controls
Automatic Climate Control System
The heating, cooling, and ventilation for the vehicle can
be controlled with this system.
Climate Control Inuence on Hybrid
Operation and Fuel Economy
To maximize your fuel economy, use the following
settings:
Set the fan knob to AUTO.
Set the air delivery knob to AUTO.
Select an air temperature setting near 75°F (23°C).
Select the Hybrid A/C button, if A/C is required.Avoid using these settings that may lead to fewer auto
stops and to higher fuel consumption:
Manual fan speed operation.
Defrost mode. Only use this setting to clear the
windows.
Extreme cold or hot air temperature settings, such
as 60°F (16°C) or 90°F (32°C).
Normal air conditioning mode, if A/C is required.
Automatic Operation
This climate control system automatically maintains the
desired temperature inside the vehicle.
Do not cover the sensor located on the top of the
instrument panel near the windshield or the sensor grille
below the climate control faceplate. These two sensors
help regulate the inside air temperature.
AUTO (Automatic Fan):Turn the fan knob to AUTO
for the system to automatically adjust the fan speed
to reach the desired inside temperature.
Temperature Control:Select the desired air
temperature between 60-90°F (16-32°C). Typically,
the best setting is near 75°F (23°C). Choosing the
coldest or warmest temperature setting does not
cause the system to heat or cool any faster.
3-18
ProCarManuals.com

To change the current air delivery mode, use the right
knob to select one of the following:
H(Vent):This mode directs air to the instrument
panel outlets.
)(Bi-Level):This mode divides the air between the
instrument panel outlets and the oor outlets.
6(Floor):This mode directs most of the air to the
oor outlets with some air directed to the windshield.
When this mode is selected, the system turns the
recirculation mode off. Recirculation mode cannot be
selected while in oor mode. This is to help prevent
window fogging.
The right knob can also be used to select defog or
defrost mode. See “Defogging and Defrosting” later in
this section.
#(Normal Air Conditioning):Press this button to
turn the air conditioning system on or off. When this
button is pressed, an indicator light comes on to show
that the air conditioning is activated. Normal Air
Conditioning (A/C) can be selected in any mode as long
as the fan is on and the outside air temperature is above
freezing. Normal A/C cannot be selected at the same
time as Hybrid Air Conditioning (A/C). A ashing indicator
light indicates that the air conditioning compressor is
currently not available.When Normal A/C is selected, the climate control system
will prevent all automatic engine start/stop operations.
This will ensure the cabin comfort is maintained. See “Air
Conditioning and Automatic Engine Start/Stop” later in
this section.
N(Hybrid Air Conditioning):Press this button to
turn the Hybrid A/C system on or off. When this button is
pressed, an indicator light comes on to show that the
Hybrid A/C is activated. Hybrid A/C can be selected in
any mode, except defrost as long as the fan is on and the
outside air temperature is above freezing. Hybrid A/C
cannot be selected at the same time as the normal air
conditioning. A ashing indicator light indicates the air
conditioning compressor is not available.
The Hybrid A/C works to balance fuel economy and air
conditioning comfort. When Hybrid A/C is used in warm
weather, the vehicle gets better fuel economy by allowing
more frequent start/stops. For additional cooling, select
Normal A/C. See “Air Conditioning and Automatic Engine
Start/Stop” later in this section.
3-20
ProCarManuals.com

Instrument Panel Cluster
The instrument panel cluster is designed to let you know at a glance how your vehicle is running. You will know how
fast you are going, about how much fuel you have and many other things you will need to know to drive safely
and economically.
United States cluster, Canada similar
3-26
ProCarManuals.com