2008 RENAULT SCENIC boot

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands87B
87B - 249
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands87B
87B - 249V9 MR-372-J84-87B000$774.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
AC004
LOCK DOORS AND BOOT
NOTESNo faults should be present or stored.
This command is for testing locking relay operation.
Note:
The driver's door circuit is shared with the fuel tank flap circuit.
Use Wiring Diagrams Technical Note for MEGANE II or SCENIC II.
One or more doors do not lock when the command is activated.
Check the condition and connection of the PP2 connector on the UCH.
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check the condition and connection of the connector on the faulty lock(s).
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check for earth on the following connections:
●Connection code MAM.
●Connection code 87H of component 140.
●Connection code MZ.
●Connection code 87A of component 139.
●Connection code MAN.
●Connection code 87G of component 141.
●Connection code MAQ.
●Connection code 87B of component 138.
●Connection code 20BC.
●Connection code 20BH of component 844.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If faulty: If OK:
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands87B
87B - 251
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands87B
87B - 251V9 MR-372-J84-87B000$774.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
AC005
AC006
UNLOCK DOORS AND BOOT
DRIVER'S DOOR UNLOCKING
NOTESNo faults should be present or stored.
This command is for testing unlocking relay operation.
The driver's door circuit is shared with the fuel tank flap circuit.
Use Wiring Diagrams Technical Note for MEGANE II or SCENIC II.
One or more doors do not unlock when the commands are activated.
Check the condition and connection of the PP2 connector on the UCH.
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check the condition and connection of the connector on the faulty lock(s).
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check for earth on:
●Connection code MAM.
●Connection code 87H.
Of component 140.
●Connection code MZ.
●Connection code 87A.
Of component 139.
●Connection code MAN.
●Connection code 87G.
Of component 141.
●Connection code MAQ.
●Connection code 87B.
Of component 138.
●Connection code 20BC.
●Connection code 20BH.
Of component 140.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If faulty: If OK:
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands87B
87B - 287
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands87B
87B - 287V9 MR-372-J84-87B000$817.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
AC034
BOOT EXTERNAL AERIAL TEST
NOTESBefore performing this command, it is essential to perform command AC037
Transmitter aerial diagnostic to ensure there is no aerial fault.
There must be no present or stored faults.
This command is for checking the hands-free boot access zone and works even if the
hands-free card does not belong to the vehicle.
Special note:
This command is for testing correct operation of the external aerial on the boot side.
If the range exceeds 1.50 m, check that there is no short circuit to the aerial earth.
This command takes 1 minute.
View the flashing of the card reader.
Use Wiring Diagrams Technical Note for MEGANE II or SCENIC II.
Check the condition and connection of the aerial connector (bent, broken tabs, etc.).
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check the condition and connection of the PE3 connector of the UCH (tabs bent, broken, etc.).
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check the insulation and continuity of the following connections to + 12 V and to earth:
●Connection code 26AM.
●Connection code 26AN between components 645 and 1378.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact Techline.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands87B
87B - 289
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands87B
87B - 289V9 MR-372-J84-87B000$817.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
AC036
CONTINUED 1
BOOT INTERNAL AERIAL
Check the condition and connection of the aerial connector (bent, broken tabs, etc.).
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check the condition and connection of the PE3 connector of the UCH (tabs bent, broken, etc.).
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check the insulation and continuity of the following connections to + 12 V and to earth:
●Connection code 26AV.
●Connection code 26AW between components 645 and 1397.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Replace the aerial if necessary.
If the fault is still present, contact Techline.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Customer complaints
87B
87B -296
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Customer complaints
87B
87B -296V9 MR-372-J84-87B000$860.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
*RAID: Renault Anti-Intruder DeviceOPENING ELEMENTS
NO SUNROOF OPENING AND CLOSING ALP24
NO SUNROOF OPENING POSITION 1, 2 or 3 ALP25
THE SUNROOF IS DIFFICULT TO CLOSE OR THE ANTI-PINCH IS
TRIGGERED WITHOUT ANY APPARENT OBSTACLEALP26
FAULT LOCKING/UNLOCKING USING CARD BUTTON ALP27
TAILGATE LOCKING/UNLOCKING FAULT VIA CARD BUTTON ALP28
BOOT OPENING FAULT
(NOT HANDS-FREE)ALP29
REAR SCREEN OPENING FAULT
(NOT HANDS-FREE)ALP30
FUEL TANK FLAP LOCKING / UNLOCKING FAULT ALP31
UNLOCKING FAULT IN HANDS-FREE MODE ALP32
LOCKING FAULT IN HANDS-FREE MODE ALP33
HANDS-FREE BOOT UNLOCKING FAULT ALP34
FAULT OPENING THE REAR SCREEN IN HANDS-FREE MODE ALP35
FAULT LOCKING/UNLOCKING ONE OR MORE DOORS ALP36
RENAULT ANTI-INTRUDER DEVICE OPERATION FAULT (RAID*) ALP37
WINDOWS FAIL TO CLOSE AFTER TWO ATTEMPTS TO LOCK ALP38

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart87B
87B - 347
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart87B
87B - 347V9 MR-372-J84-87B000$946.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ALP27 Locking/unlocking fault when pressing card button.
NOTESCheck that there is no APC or card in the card reader.
Check that no opening element is detected as open by the UCH (look at the symbol on
the instrument panel).
First carry out a function fault finding check.
Test with the other card.
Check the condition of the battery (inserted the wrong way round, flat, incorrect
model).
If the fault is still present after having carried out a test with the other card, it could be that:
–There may be radiofrequency interference in the area (ET066 Card button press received is NO for both
cards). Move the vehicle to try again.
–The UCH which has just been replaced does not have the correct part number (external or internal UCH
aerial). Use the correct UCH part number.
–If the vehicle is a Scenic II fitted with a tyre pressure monitoring system, check that the external UCH aerial
is connected correctly.
–Check that the UCH for the vehicle is not blank. Check that the UCH on the vehicle has not been used on
another vehicle.
Check that statuses ET066 Card button press received and ET067 Card button press recognised are YES
after pressing the card's lock or unlock button.
If not, apply the fault finding procedures for those statuses.
Check that statuses ET066 Card button press received and ET067 Card button press recognised are YES
after pressing the card's lock or unlock button.
If not, apply the fault finding procedures for those statuses.
Check that status ET014 Control power level is not APC.
If not, apply the fault finding procedures for this status.
Check that statuses ET041 Opening rear screen, ET042 Passenger's door, ET050 Tailgate/Boot, ET051 Rear
left-hand door, ET052 Rear left-hand door and ET053 Driver's door are CLOSED.
If not, apply the fault finding procedures for those statuses.
If the fault is still present, contact Techline.
AFTER REPAIRCarry out a complete check using the diagnostic tool.
UCH_V44_ALP27 /UCH_V48_ALP27/UCH_V4C_ALP27/
UCH_V4D_ALP27/UCH_V4F_ALP27/UCH_V50_ALP27

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart87B
87B - 348
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart87B
87B - 348V9 MR-372-J84-87B000$946.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ALP28 Fault locking/unlocking boot via card button
NOTESCheck that there is no APC or card in the card reader.
First carry out a function fault finding check.
Test with the other card.
Check the condition of the batteries.
Check if the direction indicator lights flash once on unlocking and twice on locking.
NOYES
Check that statuses ET066 Card button press received and ET067 Card button press
recognised are YES after pressing the card's lock or unlock button.
If not, apply the fault finding procedures for those statuses.
Check that the boot is not detected as OPEN using status ET050 Tailgate/Boot.
If not, apply the fault finding procedures for this status.
Check that the boot is not detected as OPEN using status ET050 Tailgate/Boot.
If not, apply the fault finding procedures for this status.
AFTER REPAIRCarry out a complete check using the diagnostic tool.
UCH_V44_ALP28 /UCH_V48_ALP28/UCH_V4C_ALP28/
UCH_V4D_ALP28/UCH_V4F_ALP28/UCH_V50_ALP28

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart87B
87B - 349
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart87B
87B - 349V9 MR-372-J84-87B000$946.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ALP29 Boot opening fault (not hands-free)
NOTESFirst carry out a function fault finding check.
The vehicle or boot must be unlocked.
Check that status ET061 Open tailgate request becomes PRESENT after pressing the boot opening button.
If not, apply the fault finding procedures for this status.
Check that the boot is not detected as OPEN using status ET050 Tailgate/Boot.
If not, apply the fault finding procedures for this status.
If the fault is still present, contact Techline.
AFTER REPAIRCarry out a complete check using the diagnostic tool.
UCH_V44_ALP29 /UCH_V48_ALP29/UCH_V4C_ALP29/
UCH_V4D_ALP29/UCH_V4F_ALP29/UCH_V50_ALP29