2008 RENAULT SCENIC light

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Configurations and programming
87B
87B-51
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Configurations and programming
87B
87B-51V9 MR-372-J84-87B000$215.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Configurations and programming
1/ GENERAL INFORMATION
The engine immobiliser protection system is controlled by a RENAULT card recognition system with random rolling
code.
A coded transponder chip (operating without a battery) independent of the remote control function is built into each
of the vehicle's RENAULT Cards.
The engine immobiliser is active a few seconds after the RENAULT Card is removed from the card reader. Its status
is shown by the flashing warning light on the instrument panel and by locking of the steering column lock.
To obtain the immobiliser code, see Technical Note 5037A, Code delivery procedure.
There are two programming methods: "Not connected" to the code server mode and "connected" to the code
server mode.
–In the "not connected" mode, the CLIP diagnostic tool supplies a programming key and the user enters the
immobiliser code.
–In the "connected" mode, the CLIP diagnostic tool automatically exchanges the programming key and the
immobiliser code.
IMPORTANT
If not all of the Renault cards are available, reallocate all Renault cards later. Cards not inserted will no longer be
allocated to this vehicle.
IMPORTANT
In "not connected" mode, once the tool has issued the programming key, the user has a limited amount of time
in which to enter the immobiliser code.
If this time expires, the CLIP diagnostic tool displays the message "Time expired. Restart the procedure.
Note:
When only the UCH is replaced, there is no operation to perform on the injection computer or the steering column
lock, they retain the same immobiliser code.
IMPORTANT
Once a part is programmed with a code, it is allocated to the vehicle; the code cannot be deleted and the part
cannot be reprogrammed with another code. The programmed code cannot be erased.
IMPORTANT
In "connected" mode, the exchange of the programming key and the entry of the immobiliser code is done
automatically.
If the connection parameters are not met, "connected" mode switches automatically to "not connected" mode.
MR-372-J84-87B000$215.mif

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Configurations and programming
87B
87B-53
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Configurations and programming
87B
87B-53V9 MR-372-J84-87B000$215.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
UCH programming procedure
–Run the Multiplex network test.
–Switch on the side lights.
–Establish dialogue with the UCH.
–Select the menu repair mode.
–Select the menu secure programming.
–Select line SC004 Program UCH.
Follow the instructions on the CLIP diagnostic tool.
In "not connected" mode, when the CLIP diagnostic tool displays the programming key, make a note of this key
and the VIN.
To obtain the immobiliser code, see Technical Note 5037A, Code delivery procedure.
Operations to be carried out after programming the UCH
●Enter the vehicle VIN in the computer using the command VP004 Enter VIN.
●After programming the UCH, allocate all of the cards using command SC006 Card allocation.
●Configure the equipment as present or not present on the vehicle using the commands
(see Configuration and programming). IMPORTANT
In "not connected" mode, the programming key can only be used for a limited amount of time, as indicated by
the CLIP diagnostic tool. After this time, the programming key and associated immobiliser code are no longer
valid. The operation must be restarted from the beginning.

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Configurations and programming
87B
87B-61
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Configurations and programming
87B
87B-61V9 MR-372-J84-87B000$215.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
–Double input: on vehicles manufactured after 10/01/2005.
1Rear left-hand door
2Rear right-hand door
7/ PROCEDURE FOR CONFIGURING PROTECTION AND SWITCHING UNIT TYPE (CF135)
This configuration is only available with a UCH Vdiag 4F or 50.
This procedure will enable certain functions of the UCH computer to be configured to differentiate between a vehicle
fitted with a phase 1 electronic layout and a vehicle fitted with a phase 2 electronic layout.
–Click on Repair mode and in the Configuration writing menu,
–confirm the line CF135 Protection and Switching Unit computer type,
–follow the procedure and enter the following data:
–CF135 UPC computer type (SIEMENS Vdiag 44 or OTHER),
–CF114 Body type (phase 1 or phase 2),
–CF112 Headlight washers on vehicle (WITH or WITHOUT): only if UCH Vdiag 50.
–confirm, follow the procedure and enter the following data:
–CF085 Valet card function (WITH or WITHOUT) Important: the Valet function is only available on vehicles for the
MEXICAN market (this configuration is only available if the vehicle is fitted with a UPC Vdiag 44): only if UCH
Vdiag 50.
–confirm and follow the procedure,
–a screen prompts the user to verify that the specifications configured are those for the vehicle,
–confirm and follow the procedure.

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Configurations and programming
87B
87B-62
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Configurations and programming
87B
87B-62V9 MR-372-J84-87B000$215.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
8/ UCH TYPE CONFIGURATION PROCEDURE (SC008)
8.1 Vdiag 44, 48
This procedure will enable the UCH to be configured in relation to the vehicle to provide optimum running.
–Click on the Repair mode and in the Programming menu,
–confirm line SC008 UCH type,
–follow the procedure and enter the following data:
–CF097 Vehicle type (3-door/4-door/5-door/cabriolet/extended MPV/MPV/Estate),
–confirm, follow the procedure and enter the following data:
–CF010 Hands-free function (WITH or WITHOUT),
–CF023 Tyre pressure monitoring system function (WITH or WITHOUT),
–CF057 Type of heating resistors (NONE, 1000 W, or 1800 W),
–CF019 Type of air conditioning (HEATING, AUTOMATIC, MANUAL),
–CF027 Type of windscreen (TINTED, HEAT INSULATING),
–CF035 Rain/light sensor (WITH or WITHOUT),
–CF014 Daytime running lights (WITH or WITHOUT),
–CF022 Factory fitted perimeter protection (WITH or WITHOUT): function only available on vehicles for the
Mexican market,
–CF173 One-touch window(s)/Sunroof (WITH or WITHOUT),
–confirm, follow the procedure and enter the following data:
–CF036 Selective opening of the opening elements (WITH or WITHOUT) Only if CF010 = WITHOUT
–confirm, follow the procedure and enter the following data:
–CF085 Valet card function (WITH or WITHOUT) Function only available in Mexico,
–(This status will only be available if the following conditions are met: CF036 Selective opening of opening
elements = WITH),
–check that the options configured are those desired and finish.

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Configurations and programming
87B
87B-63
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Configurations and programming
87B
87B-63V9 MR-372-J84-87B000$215.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
8.2 Vdiag 4C and 4D:
This procedure will enable the UCH to be configured in relation to the vehicle to provide optimum running.
–Click on the Repair mode and in the Programming menu,
–confirm line SC008 UCH type,
–follow the procedure and enter the following data:
CF097 Vehicle type (3-door/4-door/5-door/cabriolet/extended MPV/MPV/Estate).
CF011 Gearbox type (BVA or BVM).
CF020 Type of driving style (Right-hand or Left-hand).
CF028 Engine type (F or K)
–confirm, follow the procedure and enter the following data:
CF010 Hands-free function (WITH or WITHOUT),
CF023 Tyre pressure monitoring system (WITH or WITHOUT),
CF057 Type of heating resistors (NONE, 1000 W, or 1800 W),
CF019 Type of air conditioning (HEATING, AUTOMATIC, MANUAL),
CF027 Type of windscreen (TINTED, HEAT INSULATING),
CF087 Front fog light (WITH or WITHOUT),
CF014 Daytime running lights (WITH or WITHOUT),
CF012 Rain sensor (WITH or WITHOUT),
CF029 External temperature sensor (WITH or WITHOUT).
–confirm, follow the procedure and enter the following data:
CF036 Selective opening of opening elements (WITH or WITHOUT): Only if CF010 = WITHOUT.
CF016 PAX system type tyre (WITH or WITHOUT): Only if CF097 = MPV or extended MPV or cabriolet and if
CF023 = WITH.
CF100 Deadlocking (WITH or WITHOUT).
CF013 Light sensor (WITH or WITHOUT): Only if CF014 = WITHOUT.
CF022 Factory fitted
perimeter protection (WITH or WITHOUT). Function only available on vehicles sold in
Mexico. CF083 One touch window(s) (WITH or WITHOUT): Absent if CF097 = Cabriolet.
–confirm, follow the procedure and enter the following data:
CF085 Valet card function (WITH or WITHOUT) Function only available in Mexico. Only if CF036 = WITH and
CF023 = WITHOUT.
–check that the options configured are those desired and finish.

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Configurations and programming
87B
87B-64
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Configurations and programming
87B
87B-64V9 MR-372-J84-87B000$215.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
8.3 Vdiag 4F and 50:
This procedure will enable the UCH to be configured in relation to the vehicle to provide optimum running.
–Click on the Repair mode and in the Programming menu,
–confirm line SC008 UCH type,
–follow the procedure and enter the following data:
–CF097 Vehicle type (3-door/4-door/5-door/cabriolet/Estate) except for Scénic (extended MPV/MPV).
–confirm, follow the procedure and enter the following data:
CF010 Hands-free function (WITH or WITHOUT),
CF023 Tyre pressure monitoring system (WITH or WITHOUT),
CF057 Type of heating resistors (NONE, 1000 W, or 1800 W),
CF019 Type of air conditioning (HEATING, AUTOMATIC, MANUAL),
CF027 Type of windscreen (TINTED, HEAT INSULATING),
CF035 Rain/light sensor (WITH or WITHOUT),
CF014 Daytime running lights (WITH or WITHOUT),
CF189 Protection type (TYPE 1, TYPE 2 or WITHOUT): TYPE 1 = with factory
fitted perimeter protection, TYPE
2 = with Cobra type alarm and WITHOUT = without factory fitted perimeter protection and without Cobra alarm.
–confirm, follow the procedure and enter the following data:
CF173 One-touch window(s)/sunroof (1 OTW* phase 1/1 OTW* phase 2/2 or 4 OTW*/WITHOUT): Absent if
CF097 = Cabriolet.
1 OTW* phase 1 = 1 driver side one touch window with a phase 1 bodywork vehicle.
1 OTW* phase 2 = 1 driver side one touch window with a phase 2 bodywork vehicle.
2 or 4 OTW = 2 or 4 one touch windows.
WITHOUT = no one touch windows on the vehicle.
–confirm, follow the procedure and enter the following data:
CF188 Production number type (Jxxxxxx or OTHER): only if CF097 = 4-doors and CF173 = 1 OTW* Phase 1.
The production number is located on the oval plate on the vehicle's right-hand side B-pillar. The production number
consists of 7 characters: 1 letter indicating the production plant followed by 6 figures.
–If the production number starts with the letter J, select Jxxxxxx.
–If the production number does not start with the letter J, select Other.
–Confirm, follow the procedure and enter the following data:
CF036 Selective opening of opening elements (WITH or WITHOUT): Only if CF010 = WITHOUT CF016 PAX
System type tyre (WITH or WITHOUT): Only if CF097 = MPV or Extended MPV and if CF023 = WITH.
–confirm, follow the procedure and enter the following data:
CF085 Valet card function (WITH or WITHOUT): Only if CF036 = WITH and CF023 = WITHOUT.
–check that the options configured are those desired and finish.
OTW*: One-touch window(s)IMPORTANT
Only configure WITH valet card function when the vehicle is electrically pre-equipped with the valet option.
Incorrect configuration may cause certain pieces of equipment to malfunction.
Note:
After having finished the UCH configuration, run command AC037 "TRANSMITTING AERIALS FAULT FINDING"
and check that there are no faults.

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Configurations and programming
87B
87B-65
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Configurations and programming
87B
87B-65V9 MR-372-J84-87B000$215.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
9) CONFIGURATION PROCEDURE FOR THE TYRE PRESSURE MONITOR FUNCTION (CF023)
10) INSTRUMENT PANEL CONFIGURATION PROCEDURE (CF145)CF023:
TYRE PRESSURE MONITOR FUNCTION
(in programming command SC008 "UCH type")
WRITING THE CONFIGURATION WITH
OR WITHOUT TYRE PRESSURE MONITOR:
●Select the Repair mode menu.
●Select the Programming menu.
●Select line SC008 then line CF023, then With or Without.
●Confirm the selection.
●Check that sure the configuration has been properly stored by checking the Read configuration menu at line
LC017 Tyre pressure monitor function.
IMPORTANT:
CONFIGURATION INCONSISTENCY BETWEEN THE INSTRUMENT PANEL AND UCH
1st case–The instrument panel detects that the tyre pressure monitor is programmed in the UCH but
not its proper configuration. The message ELECTRONIC FAULT appears, then the
4 wheels disappear on the instrument panel display, and the Service warning light comes
on.
2nd case–The instrument panel detects that the tyre pressure monitor is programmed in its own
configuration but the UCH fails to respond to any requests from the instrument panel (not
configured in UCH). The message TYRE SENSOR FAULT will appear, the four wheels
will disappear from the instrument panel display and the Service warning light will come
on.
CF145:
TYRE PRESSURE MONITOR
●After the multiplex network test, select Instrument panel.
●Select Repair mode.
●Select Write configuration.
●Select line CF145, then With or Without.
●Confirm the selection.
●Check that the configuration has been properly stored in the Read configuration menu at line LC056 Tyre
pressure monitor.

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Configurations and programming
87B
87B-66
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Configurations and programming
87B
87B-66V9 MR-372-J84-87B000$215.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
The UCH configurations performed in accordance with the vehicle's equipment level are configured using
the CLIP tool:
Configuration
readingConfigurationName of
configurationChoice of
configurationVdiag
LC001Hands-free functionSC008 UCH typeWITH/WITHOUT44, 48, 4C, 4D, 4F
and 50
LC002External temperature
sensorCF029WITH/WITHOUT 4C, 4D, 4F and 50
LC003DeadlockingCF009WITH/WITHOUT44, 48, 4C, 4D, 4F
and 50
LC004One-touch window(s)SC008 UCH typeWITH/WITHOUT 4C and 4D
LC005Gearbox typeCF011Manual/
Automatic44, 48, 4C, 4D, 4F
and 50
LC006Rain detectorSC008 UCH typeWITH/WITHOUT 44, 48, 4C, 4D
LC007Light sensorSC008 UCH typeWITH/WITHOUT 44, 48, 4C, 4D
LC008Daytime running lightsCF014WITH/WITHOUT44, 48, 4C, 4D, 4F
and 50
LC009Hazard warning lights
illuminated upon impactAutomatic
configurationWITH/WITHOUT 44, 48, 4C, 4D
LC010Tyre type Run flat tyreSC008 UCH typeWITH/WITHOUT44, 48, 4C, 4D, 4F
and 50
LC011Vehicle typeSC008 UCH typeCabriolet/3-door/
All except E and
C44, 48, 4C, 4D
LC012Automatic relockingCF018WITH/WITHOUT 44, 48, 4C, 4D
LC013Type of air conditioningSC008 UCH typeHeating/
Automatic/
Manual 44, 48, 4C, 4D, 4F
and 50
LC014Type of driving styleCF020LEFT-HAND/
RIGHT-HAND 44, 48, 4C, 4D, 4F
and 50
LC015Front fog lightsCF021WITH/WITHOUT44, 48, 4C, 4D, 4F
and 50
LC016Valet card functionSC008 UCH type WITH/WITHOUT 4C, 4D, 4F and 50