2008 RENAULT SCENIC light

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart87B
87B - 304
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart87B
87B - 304V9 MR-372-J84-87B000$903.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ALP4 No left-hand direction indicator
NOTESOnly check this customer complaint after performing a complete check with the
diagnostic tool.
Check the bulbs.
Are the bulbs in good condition?
YES
Check the + 12 V supply and earth on the headlight
connectors (see interpretation of DF013 Left-hand
direction indicator circuit).
Is there a supply?
NO
Check status ET083 Left-hand direction indicator
request by moving the control stalk.
Is status ET083 present?
YES
Perform command AC022 Left-hand direction
indicator.
Does the left-hand direction indicator come on?
YES
Check the UCH connectors.
If the fault is still present, contact the Techline.
NOReplace the bulbs.
YESVerify that there is no corrosion on the
connector.
If the connector is faulty and if there is a
repair procedure (see Technical Note
6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair
the connector; otherwise, replace the
wiring.
NOApply interpretation of status ET083 Left-
hand direction indicator request.
NOApply interpretation of command AC022
Left-hand direction indicator.
AFTER REPAIRCarry out a complete check using the diagnostic tool.
UCH_V44_ALP4/UCH_V48_ALP4/ UCH_V4C_ALP4/
UCH_V4D_ALP4 /UCH_V4F_ALP4/UCH_V50_ALP4

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart87B
87B - 305
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart87B
87B - 305V9 MR-372-J84-87B000$903.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ALP5No side lights
(Lights without xenon bulb)
NOTESOnly check this customer complaint after performing a complete check with the
diagnostic tool.
Use Wiring Diagrams Technical Note for MEGANE II or SCENIC II.
Check the bulbs.
Are the bulbs in good condition?
YES
Check the + 12 V supply between connections LPD
and MAS of component 226.
Check the + 12 V supply between connections LPG
and MAS of component 270.
Are the feeds correct?
NO
Check status ET081 Lighting stalk position.
Is the side lights request on side lights?
YES
Run fault finding on the Protection and Switching
Unit.
NOReplace the bulbs.
YESVerify that there is no corrosion on the
connector.
If the connector is faulty and if there is a
repair procedure (see Technical Note
6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the
connector; otherwise, replace the wiring.
NOApply interpretation of status ET081
Lighting stalk position.
AFTER REPAIRCarry out a complete check using the diagnostic tool.
UCH_V44_ALP5/UCH_V48_ALP5/ UCH_V4C_ALP5/
UCH_V4D_ALP5 /UCH_V4F_ALP5/UCH_V50_ALP5

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart87B
87B - 306
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart87B
87B - 306V9 MR-372-J84-87B000$903.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ALP6NO DIPPED HEADLIGHTS
(Lights without xenon bulb)
NOTESOnly check this customer complaint after performing a complete check with the
diagnostic tool.
Use Wiring Diagrams Technical Note for MEGANE II or SCENIC II.
Check the bulbs.
Are the bulbs in good condition?
YES
Check the + 12 V supply between connections RPG
and MAS of component 270.
Check the + 12 V supply between connections RPD
and MAS of component 270.
If the connection or connections are faulty and there
is a repair procedure (see Technical Note 6015A,
Electrical wiring repair, Wiring: Precautions for
repair), repair the wiring, otherwise replace it.
Are the feeds correct?
NO
Check status ET081 Lighting stalk position.
Is the dipped beam headlight request on dipped
beam?
YES
Run fault finding on the Protection and Switching
Unit and check the dipped headlight F8C fuses
(Vdiag 44 UPC) and F3 and F4 fuses (Vdiag 48 or
above UPC) on the UPC.
NOReplace the bulbs.
YESVerify that there is no corrosion on the
connector.
Repair if necessary.
NOApply interpretation of status ET081
Lighting stalk position.
AFTER REPAIRCarry out a complete check using the diagnostic tool.
UCH_V44_ALP6/UCH_V48_ALP6/ UCH_V4C_ALP6/
UCH_V4D_ALP6 /UCH_V4F_ALP6/UCH_V50_ALP6

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart87B
87B - 307
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart87B
87B - 307V9 MR-372-J84-87B000$903.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ALP7No main beam headlights
(Lights without xenon bulb)
NOTESOnly check this customer complaint after performing a complete check with the
diagnostic tool.
Use Wiring Diagrams Technical Note for MEGANE II or SCENIC II.
Check the bulbs.
Are the bulbs in good condition?
YES
Check the + 12 V supply on connection RPD of
component 226 and on connection RPG of
component 227.
Check for earth on connection MAS of
components 226 and 227.
If the connection or connections are faulty and there
is a repair procedure (see Technical Note 6015A,
Electrical wiring repair, Wiring: Precautions for
repair), repair the wiring, otherwise replace it.
Are the feeds correct?
NO
Check status ET081 Lighting stalk position.
Does the side light request occur on main beam?
YES
Run fault finding on the Protection and Switching
Unit.
Check the F8A and F8B fuses (Vdiag 44 UPC) and
F6 and F7 fuses (Vdiag 48 or above UPC).
NOReplace the bulbs.
YESVerify that there is no corrosion on the
connector.
Repair if necessary.
NOApply interpretation of status ET081
Lighting stalk position.
AFTER REPAIRCarry out a complete check using the diagnostic tool.
UCH_V44_ALP7/UCH_V48_ALP7/ UCH_V4C_ALP7/
UCH_V4D_ALP7 /UCH_V4F_ALP7/UCH_V50_ALP7

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart87B
87B - 308
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart87B
87B - 308V9 MR-372-J84-87B000$903.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ALP8 No front fog lights
NOTESOnly check this customer complaint after performing a complete check with the
diagnostic tool.
Check status ET111 Front fog lights request with
the stalk in the front fog lights position.
Is status ET111 Present?
YES
Perform command AC008
Front fog lights.
Do the front fog lights come on?
YES
Check the UCH connectors.
If the fault is still present, contact the Techline.
NOApply interpretation of status ET111 Front
fog light request.
NOApply interpretation of command AC008
Front fog lights.
AFTER REPAIRCarry out a complete check using the diagnostic tool.
UCH_V44_ALP8/UCH_V48_ALP8/ UCH_V4C_ALP8/
UCH_V4D_ALP8 /UCH_V4F_ALP8/UCH_V50_ALP8

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart87B
87B - 315
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart87B
87B - 315V9 MR-372-J84-87B000$903.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ALP14No headlight washers
(Only if VDIAG 44 UPC)
NOTESOnly check this customer complaint after performing a complete check with the
diagnostic tool.
Set the stalk to side lights and check whether status
ET081 Lighting stalk position is to Side lights.
YES
Check whether status ET078 Front windscreen
washer request is Present when the stalk is
operated.
YES
Run commands AC030 Headlight washer 1 relay
and AC031 Headlight washer 2 relay.
Can commands AC030 and AC031 be run?
YES
Check the condition of the pipes and nozzles. Repair
if necessary.
If the fault is still present, contact the Techline.
NOApply interpretation of status ET081
Lighting stalk position.
NOApply interpretation of status ET078
Windscreen washer request.
NOApply interpretation of commands AC030
Headlight washer 1 relay and AC031
Headlight washer 2 relay.
AFTER REPAIRCarry out a complete check using the diagnostic tool.
UCH_V44_ALP14 /UCH_V48_ALP14/UCH_V4C_ALP14/
UCH_V4D_ALP14/UCH_V4F_ALP14/UCH_V50_ALP14

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart87B
87B - 348
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart87B
87B - 348V9 MR-372-J84-87B000$946.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ALP28 Fault locking/unlocking boot via card button
NOTESCheck that there is no APC or card in the card reader.
First carry out a function fault finding check.
Test with the other card.
Check the condition of the batteries.
Check if the direction indicator lights flash once on unlocking and twice on locking.
NOYES
Check that statuses ET066 Card button press received and ET067 Card button press
recognised are YES after pressing the card's lock or unlock button.
If not, apply the fault finding procedures for those statuses.
Check that the boot is not detected as OPEN using status ET050 Tailgate/Boot.
If not, apply the fault finding procedures for this status.
Check that the boot is not detected as OPEN using status ET050 Tailgate/Boot.
If not, apply the fault finding procedures for this status.
AFTER REPAIRCarry out a complete check using the diagnostic tool.
UCH_V44_ALP28 /UCH_V48_ALP28/UCH_V4C_ALP28/
UCH_V4D_ALP28/UCH_V4F_ALP28/UCH_V50_ALP28

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart87B
87B - 354
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart87B
87B - 354V9 MR-372-J84-87B000$946.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ALP33 Locking fault in hands-free mode
NOTESCheck that there is no APC or card in the card reader.
Conduct the tests with the other cards allocated to the vehicle.
First carry out a function fault finding check.
Make sure all the doors are fully closed (check that the interior lights are off or switch
on the ignition to check that no door is open from the instrument panel symbol).
Visually check that the lock buttons are not stuck in the down position.
Check that one of the cards has not been disabled (locked in the vehicle), activate the
+ after ignition feed with this card and attempt to unlock again with it.
If the fault only affects one card, replace the faulty card.
Make sure statuses ET058, ET059 and ET060 indicating a press on the lock button for each door or the boot
become active when the button is pressed.
Test all the lock buttons.
See the section for dealing with the status(es) concerned.
Make sure that the cards belong to the vehicle and are properly configured by running command SC005 Check
card.
If the cards belong to the vehicle but have a faulty configuration, program the cards.
Run command AC037 Transmitter aerial fault finding and see if a fault appears.
In the event of a present or stored fault, refer to the procedure for it.
Run the following commands and check the card coverage zone on each side of the vehicle:
AC032 Driver's side external aerial test
AC033 Passenger's side external aerial test
AC034 Boot external aerial test.
The card reader starts to flash as soon as a card is detected in the coverage zone.
The maximum distance from the vehicle is 1.5 m.
If not correct, apply the fault finding procedure associated with each command.
This mode enables a Mégane hands-free card to be detected in the coverage zone of the vehicle or that of
another vehicle.
Configure the UCH in hands-free function (see Configurations and programming).
If the fault is still present, contact Techline.
AFTER REPAIRCarry out a complete check using the diagnostic tool.
UCH_V44_ALP33 /UCH_V48_ALP33/UCH_V4C_ALP33/
UCH_V4D_ALP33/UCH_V4F_ALP33/UCH_V50_ALP33