2008 RENAULT SCENIC diagram

MULTIMEDIA
Fault finding - Interpretation of faults
86C
86C - 23V5 MR-372-J84-86C050$468.mif
ITS
Program No.: 0020
Vdiag No.: 04
DF030
PRESENT
OR
STOREDGPS AERIAL CIRCUIT
CO : Open circuit
NOTESConditions for applying the fault finding procedure to the stored fault:
Apply this fault finding procedure if the fault reappears as present or stored after it has
been cleared and the ignition has been switched off and on again.
Use the Wiring Diagrams Technical Note, Scenic II.
Check the condition and connection of the GPS aerial 2-track connectors (component code 886) and of the
navigation computer (component code 662) (broken, oxidised, bent tabs).
Manipulate the wiring harness at the connectors to produce a change in status (present → stored).
If the connectors are faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connectors; otherwise, replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connections:
●connection code 46CB,
●connection code TB15,
between components 662 and 886.
If any connection is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring; otherwise, replace the wiring.
If the connections are correct, replace the GPS aerial.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults using command RZ001 Fault memory.
Deal with any other faults.
ITS_V04_DF030ITSJ84ph2V1.0

MULTIMEDIA
Fault finding - Interpretation of statuses
86C
86C - 29V5 MR-372-J84-86C050$624.mif
ITS
Program no.: 0020
Vdiag No.: 04MULTIMEDIA
Fault finding - Interpretation of statuses
ET003
+ 12 V SIDE LIGHTS FEED
NOTESVisually check that the side lights are working. Carry out fault finding on the steering
column switches and the side lights.
Use the Wiring Diagrams Technical Note, Scenic II.
Check the condition of the 7.5 A fuse in the engine compartment connection unit (component code 1337).
Check the condition and connection of the navigation central control connectors (component code 1657) and of
the CD changer (component code 1272) (broken, bent tabs).
If the connectors are faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connectors; otherwise, replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the LPG connection between
components 1337, 1272 and 1657.
If the connection is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring; otherwise, replace the wiring.
If the fault is still present, contact the Techline.
AFTER REPAIRRepeat the conformity check from the start.
ITS_V04_ET003ITSJ84ph2V1.0
MR-372-J84-86C050$624.mif

MULTIMEDIA
Fault finding - Interpretation of statuses
86C
86C - 30V5 MR-372-J84-86C050$624.mif
ITS
Program no.: 0020
Vdiag No.: 04
ET006
ET007
ET009
ET010
ET034+ BUTTON
- BUTTON
UPPER BUTTON
LOWER BUTTON
MODE BUTTON
NOTESThere must be no present or stored faults.
Use the Wiring Diagrams Technical Note, Scenic II.
Check the condition and connection of the steering column switch 10-track connector (component code 1519) and
of the receiver 32-track connector (component code 261) (broken, oxidised, bent tabs).
If the connectors are faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connectors; otherwise, replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connections:
●connection code 34AQ,
●connection code 34AU,
●connection code 34AS,
●connection code 34AR,
●connection code 34AP,
●connection code 34AT,
●connection code 34AO,
between components 261 and 1519.
If any connection is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring; otherwise, replace the wiring.
AFTER REPAIRRepeat the conformity check from the start.
ITS_V04_ET006/ ITS_V04_ET007/ITS_V04_ET009/ITS_V04_ET010/ITS_V04_ET034 ITSJ84ph2V1.0

MULTIMEDIA
Fault finding - Interpretation of statuses
86C
86C - 32V5 MR-372-J84-86C050$624.mif
ITS
Program no.: 0020
Vdiag No.: 04
ET017
COMMUNICATION CONNECTION BUTTON
NOTESThere must be no present or stored faults.
Use the Wiring Diagrams Technical Note, Scenic II.
Check the condition and connection of the steering column switch 10-track connector (component code 1519) and
of the receiver 32-track connector (component code 261) (broken, oxidised, bent tabs).
If the connectors are faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connectors; otherwise, replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connections:
●connection code 34AT,
●connection code 34AO,
between components 261 and 1519.
If any connection is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring; otherwise, replace the wiring.
Carry out the following checks on component 1519 using an ohmmeter:
●Communication button pressed: the resistance should be less than 150 Ω between connections 34AT and
34AO.
●Communication button released: there should be insulation between connections 34AT and 34AO.
If the measurements taken do not correspond to the values above, replace component 1519 (see MR 370
Mechanical 84A, Control - signals, Wiper switch: Removal - Refitting).
If the fault is still present, contact the Techline.
AFTER REPAIRRepeat the conformity check from the start.
ITS_V04_ET017ITSJ84ph2V1.0

MULTIMEDIA
Fault finding - Interpretation of statuses
86C
86C - 33V5 MR-372-J84-86C050$624.mif
ITS
Program no.: 0020
Vdiag No.: 04
ET018
TUMBLEWHEEL ACTION
NOTESThere must be no present or stored faults.
Use the Wiring Diagrams Technical Note, Scenic II.
Check the condition and connection of the steering column switch 10-track connector (component code 1519) and
of the receiver 32-track connector (component code 261) (broken, oxidised, bent tabs).
If the connectors are faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connectors; otherwise, replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connections:
●connection code 34AU,
●connection code 34AS,
●connection code 34AT,
●connection code 34AR,
between components 1519 and 261.
If any connection is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring; otherwise, replace the wiring.
Check the continuity of component 1519:
–between connections 34AR and 34AT,
–between connections 34AR and 34AS,
–between connections 34AR and 34AU.
Wheel checking procedure (see MR 370 Mechanical 84A, Control - signals, Radio control satellite: Test).
If there is no continuity, replace component 1519 (see MR 370 Mechanical 84A, Control - signals, Wiper switch:
Removal - Refitting).
If the fault is still present, contact the Techline.
AFTER REPAIRRepeat the conformity check from the start.
ITS_V04_ET018ITSJ84ph2V1.0

MULTIMEDIA
Fault finding - Interpretation of statuses
86C
86C - 34V5 MR-372-J84-86C050$624.mif
ITS
Program no.: 0020
Vdiag No.: 04
ET024
REVERSE GEAR ENGAGED
NOTESThere must be no present or stored faults.
Use the Wiring Diagrams Technical Note, Scenic II.
Carry out fault finding on the Protection and Switching Unit (see 87G, Engine compartment connection unit).
Check the condition and connection of the navigation computer 32-track connector (component code 662) (broken,
oxidised, bent tabs).
If the connector is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check the condition and connection of the Protection and Switching Unit MN and CN connectors (Vdiag 48)
(component code 1337) (broken, oxidised, bent tabs).
If the connectors are faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connectors; otherwise, replace the wiring.
Check the insulation, continuity and the absence of interference resistance of the H66P connection between
components 662 and 1337.
If any connection is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring; otherwise, replace the wiring.
If the fault is still present, contact the Techline.
AFTER REPAIRRepeat the conformity check from the start.
ITS_V04_ET024ITSJ84ph2V1.0

MULTIMEDIA
Fault finding - Interpretation of parameters
86C
86C - 36V5 MR-372-J84-86C050$728.mif
ITS
Program no.: 0020
Vdiag No.: 04MULTIMEDIA
Fault finding - Interpretation of parameters
PR002
VEHICLE SPEED
NOTESCarry out a road test to obtain a variation of parameter PR002 Vehicle speed.
There must be no present or stored faults.
Use the Wiring Diagrams Technical Note, Scenic II.
If no value for parameter PR002 Vehicle speed appears on the tool, check the insulation, continuity and the
absence of interference resistance of the 47F connection between components 662 and 118 or 1094, depending
on the vehicle's equipment level.
If the connection is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring; otherwise, replace the wiring.
If the value for parameter PR002 Vehicle speed is incorrect, carry out fault finding on the ABS system (see 38C,
Anti-lock braking system).
If the fault is still present, contact the Techline.
AFTER REPAIRRepeat the conformity check from the start.
ITS_V04_PR002ITSJ84ph2V1.0
MR-372-J84-86C050$728.mif

MULTIMEDIA
Fault finding - Interpretation of commands
86C
86C - 39V5 MR-372-J84-86C050$832.mif
ITS
Program no.: 0020
Vdiag No.: 04
AC004
SPEAKER TEST
NOTESThis command activates, one by one, the front left-hand tweeters, front right-hand
tweeters, front right-hand bass, rear right-hand bass, rear left-hand bass and front
right-hand bass speakers.
Special note:
Check the output setting on the right-hand and left-hand speakers (press the SET
button, select Balance) then the output setting on the front and rear speakers (press
the SET button and then select Fad).
Use the Wiring Diagrams Technical Note, Scenic II.
Check the condition and connection of the receiver connector B (component code 261) and of the faulty speaker
connector (component code 365, 191, 366, 189, 190, 192) (broken, oxidised, bent tabs).
If the connectors are faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connectors; otherwise, replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connections:
●connection code 34E,
●connection code 34F,
between components 261, 365 and 191.
●connection code 34D,
●connection code 34C,
between components 261 and 189.
●connection code 34A,
●connection code 34B,
between components 261 and 190.
●connection code 34G,
●connection code 34H,
between components 261, 366 and 192.
If any connection is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring; otherwise, replace the wiring.
If the checks reveal no faults, but one or more of the speakers does not work, replace the faulty speaker(s).
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out another fault finding check on the system.
ITSJ84ph2V1.0