ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults87G
87G-38V7 MR-372-J84-87G050$330.mif
UPC
Vdiag No.: 48, 4C
DF020
PRESENT
OR
STOREDFRONT FOG LIGHT CIRCUIT
CO: Open circuit
CC.0: Short circuit to earth
CO
NOTESSpecial note:
To display this fault as present or stored, run the command
AC016 Electrical supply circuit test.
Use Wiring Diagrams Technical Note for Mégane II or
Scénic II.
Check that the front fog light bulbs are sound.
Repair if necessary.
Check the condition and connection of the 2-track connectors for the front fog lights, component code 176 and
177 (tabs broken, bent or oxidised).
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the connector.
Check that the earth on connection code MAS for the front right-hand fog light, component code 176 is perfect.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring otherwise replace the wiring.
Check that the earth on connection code MAS for the front left-hand fog light, component code 177 is perfect.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring otherwise replace the wiring.
Check the condition and connection of the 8-track connector AN for the Protection and Switching Unit,
component code 1337 (tabs bent, broken, oxidised).
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the connector.
Check the insulation, continuity and the absence of interference resistance on the following connections:
–8E between components 1337 and 177,
–8F between components 1337 and 176.
If the connection or connections are faulty and if there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the fitting and switch for the front fog lights.
Repair if necessary or replace the light(s) if faulty.
If the fault is still present, contact the Techline.
AFTER REPAIRRun command AC016 "Electrical supply circuits test".
Erase the faults from the computer memory, switch the + after ignition supply off and
back on again and run another check using the diagnostic tool.
USM_V48_DF020/USM_V4C_DF020
ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands87G
87G - 79V7 MR-372-J84-87G050$770.mif
UPC
Vdiag No.: 48, 4C
AC004
FRONT FOG LIGHTS
NOTESSpecial notes:
Use this command only for vehicles fitted with front fog lights.
Check the condition and connection of fuse 5 (20A) on the Protection and Switching
Unit. Replace it if necessary.
Check the condition and connection of the bulbs. Replace them if necessary.
Use Wiring Diagrams Technical Note for Mégane II or Scénic II.
Check the condition and connection of the fog lights, component codes 176 and 177 (tabs bent, broken or
oxidised).
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the connector.
Check for earth connection code MAS on the headlights, component codes 176 and 177.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check for + 12 V on connection codes 8E and 8F for the fog lights whilst running the command.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the condition and connection of the Protection and Switching Unit 8-track AN connector, connection
code 1337 (tabs broken, bent or oxidised).
If the connector is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the connector.
Check the insulation, continuity and the absence of interference resistance on the following connections:
–8E, between components 1337 and 177,
–8F, between components 1337 and 176.
If the connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact Techline.
AFTER REPAIRRepeat the conformity check from the start.
