2008 RENAULT SCENIC check engine light

ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands87G
87G - 79V7 MR-372-J84-87G050$770.mif
UPC
Vdiag No.: 48, 4C
AC004
FRONT FOG LIGHTS
NOTESSpecial notes:
Use this command only for vehicles fitted with front fog lights.
Check the condition and connection of fuse 5 (20A) on the Protection and Switching
Unit. Replace it if necessary.
Check the condition and connection of the bulbs. Replace them if necessary.
Use Wiring Diagrams Technical Note for Mégane II or Scénic II.
Check the condition and connection of the fog lights, component codes 176 and 177 (tabs bent, broken or
oxidised).
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the connector.
Check for earth connection code MAS on the headlights, component codes 176 and 177.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check for + 12 V on connection codes 8E and 8F for the fog lights whilst running the command.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the condition and connection of the Protection and Switching Unit 8-track AN connector, connection
code 1337 (tabs broken, bent or oxidised).
If the connector is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the connector.
Check the insulation, continuity and the absence of interference resistance on the following connections:
–8E, between components 1337 and 177,
–8F, between components 1337 and 176.
If the connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact Techline.
AFTER REPAIRRepeat the conformity check from the start.

ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands87G
87G - 86V7 MR-372-J84-87G050$770.mif
UPC
Vdiag No.: 48, 4C
AC013
HEADLIGHT WASHER RELAY
NOTESSpecial notes:
Check the condition and connection of fuse 21 (15A) on the Protection and
Switching Unit. Replace it if necessary.
The headlight washer pump operates if the dipped headlights are lit and the
windscreen washer switch is pressed and held.
Use Wiring Diagrams Technical Note for Mégane II or Scénic II.
Check the condition and connection of the headlight washer pump component code 219 (tabs bent, broken or
oxidised).
If the connector is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the connector.
Check the condition and connection of the Protection and Switching Unit connector (tabs bent, broken, or
oxidised).
If the connector is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the connector.
To check that the pump is working properly, supply the pump's tracks directly in one direction and then the other.
If the pump does not rotate, replace it.
Check for + 12 V alternately on connection code 39C of the headlight washer pump connector.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the insulation, continuity and the absence of interference resistance on the following connections:
–39A, between components 1337 and 219,
–39C, between components 1337 and 219.
If the connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact Techline.
AFTER REPAIRRepeat the conformity check from the start.

ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands87G
87G - 87V7 MR-372-J84-87G050$770.mif
UPC
Vdiag No.: 48, 4C
AC014
ALTERNATOR REGULATION
NOTESConditions for the application of the command:
–engine running at idling speed and warm engine,
–air conditioning off,
–check that the passenger compartment blower unit is not operating.
–check that the cooling fan assemblies are not operating,
–if fault DF007 UPC-alternator connection is declared present, deal with this fault
first,
–check the conformity of PR010 Alternator charge (see Interpretation of
parameters).
Effect of command:
–for 30 seconds, the Protection and Switching Unit sets the alternator a regulation
voltage of 15 V ± 0.5,
–then for another 30 seconds, the Protection and Switching Unit imposes a
regulation voltage of 13 V ± 0.5 on the alternator.
Switch off all the electrical consumers (fans, main beam headlights, etc.).
Measure the voltage across the alternator terminals, between the B+ terminal and the alternator chassis earth.
Run AC014 Alternator regulation.
Wait 20 seconds,
For 10 seconds the alternator voltage should be 15 V ± 0.5.
Wait 20 seconds,
For 10 seconds the alternator voltage should be 13 V ± 0.5.
Switch on the heated rear screen and the main beam headlights.
Run AC014 again.
Wait 20 seconds,
For 10 seconds the alternator voltage should be 15 V ± 0.5.
Wait 20 seconds,
For 10 seconds the alternator voltage should be 13 V ± 0.5.
If the values obtained are not correct, replace the alternator (see MR 364 or MR 370 Mechanical, 16A, Starting-
Charging, Alternator: Removal - Refitting).
AFTER REPAIRRepeat the conformity check from the start.

ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Fault finding charts87G
87G-91V7 MR-372-J84-87G050$880.mif
UPC
Vdiag No.: 48, 4C
ALP3No backlighting of the various functions in the passenger
compartment
NOTESMake sure that the side lights are working; if not, refer to the procedure for command
AC003 Side lights.
Use Wiring Diagrams Technical Note for Mégane II or Scénic II.
Check the condition and connection of the defective functions.
If the connector is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the connector.
Check for earth on the defective function(s).
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
With the side lights on, check for 12 V on the defective function(s).
If correct, replace the defective component.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the insulation, continuity, and the absence of interference resistance between the defective function
and the Protection and Switching Unit:
Right-hand headlight component code 226, rear right-hand
lights component code 172, right-hand and left-hand heated
seat control component codes 1513 and 1514, parking distance
control switch component code 1540, cruise control/speed
limiter control component code 1081, ESP on/off button
component code 1106, gear lever display component code
1129, hard roof switch component code 1482, simultaneous
window control component code 854, LPG or petrol selector
switch component code 1003, right-hand number plate light
component code 166.LPDConnector CN of the
Protection and Switching
Unit, component code
1337.
Left-hand rear light component code 173, left-hand headlight
component code 227, child safety switch component code 135,
CD changer component code 1272, radio component code
261, multifunction display component code 653, headlight
adjustment rheostat switch component code 1390, warning/door
locking switch component code 1391, first cigarette lighter
component code 101.LPGConnector CN of the
Protection and Switching
Unit, component code
1337.
If the connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.
AFTER REPAIRCheck that no fault is present.
USM_V48_ALP3 /USM_V4C_ALP3

ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Tests87G
87G-94V7 MR-372-J84-87G050$935.mif
UPC
Vdiag No.: 48, 4C
TEST1
CONTINUED
With the engine running, main beam
headlights and heated rear screen on,
measure the voltage between the B+
battery feed and B+ alternator feed
Check the condition of all the wires connecting the
battery, alternator and starter and that all of their
terminals are correctly tightened. Is the voltage > 0.7 V?
Repair any damaged wires and terminals. If the
connection is faulty and if there is a repair
procedure (see Technical Note 6015A Electrical
wiring repair, Wiring: Precautions for repair),
repair the wiring, otherwise replace the wiring
With the engine running, main beam
headlights and heated rear screen on,
measure the voltage between the B- battery
feed and the alternator frame.Check the earths for the engine, the alternator, the
chassis, the gearbox, the battery or the starter
(check for tightness, check the condition of the
terminals and the condition of the wires) (see
Technical Note for the relevant vehicle). Is the voltage > 0.7 V?
Repair any damaged wires and terminals. If the
connection is faulty and if there is a repair
procedure (see Technical Note 6015A Electrical
wiring repair, Wiring: Precautions for repair),
repair the wiring, otherwise replace the wiring The electrical circuit is in good order.
A
YES
YES
NO
YES
NO
AFTER REPAIRCarry out a complete check with the diagnostic tool.