2008 RENAULT SCENIC ignition

86D-26V1 MR-372-J84-86D050$100.mif
MULTIMEDIA NETWORK INTERFACE UNIT
Fault finding – Conformity check86D
BIC
Vdiag No.: 14
FUNCTION: MULTIMEDIA
SUB-FUNCTION: USER SELECTION
*LPN: Low Price Navigation
NOTESOnly carry out a conformity check after a complete check with the diagnostic tool. The
values shown in this conformity check are given as a guide.
Application conditions: Engine stopped, ignition on, and the radio switched on.
FunctionParameter or status
Checked or actionDisplay and notes Fault finding
ButtonET002:Radio on/off buttonINACTIVE
ACTIVE
This status remains
active until the ignition
is switched off.In the event of an
inconsistency, run fault finding
on the LPN* radionavigation
(see 86A, Radio)
Battery voltagePR002:Battery voltage12 V < X < 15 VIn the event of an
inconsistency, consult the
interpretation of fault DF005
Supply.
Vehicle speedPR003:Vehicle speedIndicates the vehicle
speed in mph (km/h).In the event of an
inconsistency, run fault finding
on the ABS (see 38C,
Anti-lock braking system).
External
temperaturePR004:External
temperature-40˚C < X < 60˚CIn the event of an
inconsistency, run fault finding
on the UCH (see 87B,
Passenger compartment
connection unit).
System
activationAC002:On/Off ButtonUsed to simulate the
pressing of the On/Off
button of the LPN*
radionavigationIn the event of an
inconsistency, consult the
interpretation of fault DF006
Activation signal and run fault
finding on the radio (see 86A,
Radio).

86D-27V1 MR-372-J84-86D050$100.mif
MULTIMEDIA NETWORK INTERFACE UNIT
Fault finding – Conformity check86D
BIC
Vdiag No.: 14
FUNCTION: MULTIMEDIA
SUB-FUNCTION: USER SELECTION (continued)
*LPN: Low Price Navigation
NOTESOnly carry out a conformity check after a complete check with the diagnostic tool. The
values shown in this conformity check are given as a guide.
Application conditions: Engine stopped, ignition on, and the radio switched on.
FunctionParameter or status
Checked or actionDisplay and notes Fault finding
ButtonET009:Repeat button (only
on Scénic II Phase 2)
PRESSED
RELEASEDIn the event of an inconsistency,
consult the interpretation of
status ET009.
ET020:"Mute" buttonIn the event of an inconsistency,
consult the interpretation of
status ET020.
ET011:+ buttonIn the event of an inconsistency,
consult the interpretation of
status ET011.
ET012:- buttonIn the event of an inconsistency,
consult the interpretation of
status ET012.
ET023:Source buttonIn the event of an inconsistency,
consult the interpretation of
status ET023.
ET025:Telephone buttonIn the event of an inconsistency,
consult the interpretation of
status ET025.
ET024:Mode button In the event of an inconsistency,
consult the interpretation of
status ET024.
Wheel actionET017:Wheel actionUPWARDS
DOWNWARDS
INACTIVEIn the event of an inconsistency,
consult the interpretation of
status ET017.

86D-28V1 MR-372-J84-86D050$100.mif
MULTIMEDIA NETWORK INTERFACE UNIT
Fault finding – Conformity check86D
BIC
Vdiag No.: 14
FUNCTION: MULTIMEDIA
SUB-FUNCTION: DISPLAY
NOTESOnly carry out a conformity check after a complete check with the diagnostic tool. The
values shown in this conformity check are given as a guide.
Application conditions: Engine stopped, ignition on, and the radio switched on.
FunctionParameter or status
Checked or actionDisplay and notes Fault finding
Side lightsET004:+12 V Side lightsOFF
ONIn the event of an
inconsistency, run fault
finding on the UCH (see 87B,
Passenger compartment
connection unit).
LightingET007:BrightnessDAY
NIGHTIn the event of an
inconsistency, consult the
interpretation of ALP 3
Steering column switch
fault.

86D-38
AFTER REPAIRWhen communication is established, deal with any faults indicated.
V1 MR-372-J84-86D050$160.mif
MULTIMEDIA NETWORK INTERFACE UNIT
Fault finding – Fault Finding Chart86D
BIC
Vdiag No.: 14
ALP 1
CONTINUED
Check that the diagnostic socket, component code 225, is correctly supplied on the following connections:
–for Espace IV Phase 2:
•BCP4 between components 225 and unitary fuse 710,
•AP10 between components 225 and 260 (+ after ignition feed),
NC and MB of component 225.
–for Scénic II Phase 2:
•BP32 between components 225 and 260,
•AP43 between components 225 and 1337 (+ after ignition feed),
•NAM and MAM of component 225.
Check the continuity, insulation and absence of interference resistance on the following connections:
•107W and 107X between components 1714 and 225,
•133B and 133C between components 1714 and 225 (for Espace IV Phase 2)
•133B and 133C between components 1714 and 645 (for Scénic II Phase 2).
If the connection(s) is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If dialogue is still not established after these various checks, replace the multimedia network interface unit,
component code 1714 (see MR 405 (Espace IV Phase 2) or MR 370 (Scénic II Phase 2) Mechanical, 83C,
On-board telematics system, Multimedia network interface unit: Removal - Refitting).
If the fault is still present, contact Techline.

86D-39
AFTER REPAIRCarry out a complete check with the diagnostic tool.
V1 MR-372-J84-86D050$160.mif
MULTIMEDIA NETWORK INTERFACE UNIT
Fault finding – Fault Finding Chart86D
BIC
Vdiag No.: 14
ALP 2 Multimedia system not switching on
NOTESSwitch on the + after ignition feed to enter fault finding mode with the computer.
Use the Wiring Diagrams Technical Note for Espace IV Phase 2 or Scénic II
Phase 2.
Is it possible to establish dialogue with the
computer?Refer to ALP 1 No dialogue with the computer.
Check the conformity of status ET002 Radio
on/off button (see Conformity check).
Is the result of the check correct?
Check that the LPN* radionavigation on/off
button is operating correctly (see 86A, Radio).
Is the result of the check correct?Contact the Techline.
NO
YES
YESA
NO
NO
YES
B
BIC_V14_ALP2

86D-42
AFTER REPAIRCarry out a complete check with the diagnostic tool.
V1 MR-372-J84-86D050$160.mif
MULTIMEDIA NETWORK INTERFACE UNIT
Fault finding – Fault Finding Chart86D
BIC
Vdiag No.: 14
ALP 3 Steering column switch fault
NOTESSwitch on the + after ignition feed to enter fault finding mode with the computer.
Refer to the Conformity check and to the interpretation of the following statuses:
–ET002 Radio on/off button,
–ET004 +12 V Side lights,
–ET007 Brightness,
–ET009 Repeat button (only on Scénic II Phase 2),
–ET011 + button,
–ET012 - button,
–ET017 Wheel action,
–ET020 Mute button,
–ET023 Source button,
–ET024 Mode button,
–ET025 Telephone button.
BIC_V14_ALP3

86D-43
AFTER REPAIRCarry out a complete check with the diagnostic tool.
V1 MR-372-J84-86D050$160.mif
MULTIMEDIA NETWORK INTERFACE UNIT
Fault finding – Fault Finding Chart86D
BIC
Vdiag No.: 14
ALP 4 Exterior temperature display fault
NOTESSwitch on the + after ignition feed to enter fault finding mode with the computer.
Carry out a fault finding procedure on the computer sending the exterior temperature signal:
–Scénic II Phase 2, see 87B, Passenger compartment connection unit.
–Espace IV Phase 2, see 83A, Instrument panel.
If the fault is still present, contact the Techline.
BIC_V14_ALP4

86D-44
AFTER REPAIRCarry out a complete check with the diagnostic tool.
V1 MR-372-J84-86D050$160.mif
MULTIMEDIA NETWORK INTERFACE UNIT
Fault finding – Fault Finding Chart86D
BIC
Vdiag No.: 14
*LPN: Low Price Navigation
ALP 5Backlighting does not change when the vehicle lights are
switched on.
NOTESSwitch on the + after ignition feed to enter fault finding mode with the computer.
Use the Wiring Diagrams Technical Note for Espace IV Phase 2 or Scénic II
Phase 2.
Switch on the lights. Carry out fault finding on the UCH
(see 87B, Passenger compartment
connection unit). Is the air conditioning control backlighting
correct?
With the lights on, check status ET007 Brightness.Check the voltage on connection BPT
(Scénic II Phase 2) or 13W (Espace IV
Phase 2) of component 1714.
Is status ET007 "Night"?
Are the checks correct?
Check the insulation, continuity and the absence
of interference resistance on the following
connections:
107X between components 1714 and 261,
107W between components 1714 and 261.
Are the checks correct?Contact the Techline.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
NO
YES
NO
YES
YESNO
YES
YES
BIC_V14_ALP5