83A-11
MR-372-J84-83A000$252.mif
V8
INSTRUMENT PANEL
Fault finding - Configurations and programming83A
TDB ph2 (EG/MG)
Prog Version: 04xx
Vdiag No.: 08, 0C
2. PROGRAMMING:
A) Switch on the ignition.
B) Enter the VIN using command VP002 Enter VIN.
C) Program the mileometer using command VP010 Mileometer update.
Check by reading parameter PR009 Mileometer.
D) Enter the oil change frequency in kilometres using command VP006 Oil change frequency in km.
Refer to the information available on the Shared World Information database via RENAULT.NET
(on the maintenance programme page) to check the vehicle configuration.
Ignition on, engine off. Run command VP006 Oil change frequency in KM.
Enter the oil change interval in km.
Example of entry:
Using the CLIP numeric keypad,
enter 20 to display 20,000 km.
or
enter 30 to display 30,000 km.
LC no. CF no. Configuration Note:
LC060 CF002 Language settingCheck the language by using a message.
LC061 CF150 Cruise control/speed limiterIf the vehicle is equipped with a Cruise
Control-Speed Limiter function: check that the
cruise control or speed limiter indicator light
comes on when the cruise control/speed
limiter button is pressed.
LC064 CF158 Seat belt reminder buzzerThis function should only be inhibited on
authorised vehicles.
LC066 CF040 Particle filter
LC090 CF006 Vehicle speed signal systemIf the vehicle is equipped with ESP: check by
pressing the ESP OFF button that the Traction
control deactivated message appears.
If the vehicle is not equipped with ESP: check
that the ESP warning light does not come on
for 3 seconds when the ignition is switched
on.
LC106 CF198O.C.S. (vdiag 08 and program
version 040B and vdiag 0C)Refer to the information available on the
Shared World Information database via
RENAULT.NET (on the maintenance
programme page) to check the vehicle
configuration.
83A-12
MR-372-J84-83A000$252.mif
V8
INSTRUMENT PANEL
Fault finding - Configurations and programming83A
TDB ph2 (EG/MG)
Prog Version: 04xx
Vdiag No.: 08, 0C
Special features for English versions
The newly supplied instrument panel is configured, by default, in kilometres.
In addition to the language configuration CF002 Language setting, carry out the calculation below to allow
the instrument panel to display consistent values between the distance before next oil change and the
desired oil change frequency.
To display the oil change frequency in miles, multiply the value in miles indicated in the Maintenance
booklet by 10 then divide by 6, to find the exact figure in kilometres.
After the value has been entered, the computer automatically performs the conversion into miles for the
oil service interval.
It is imperative to use the following procedure for correct functioning of the range and oil change
frequency.
Example: 18,000 miles x 10 = 180 000 miles, then divide by 6 = 30,000 km (Enter 30)
Check by reading parameter PR005 Oil change frequency in km.
A) Program the distance to next oil service in kilometres using command VP008 Distance to next oil
service: current value in KM.
Check by reading parameter PR007 Distance to next oil service: current value in KM.
B) Program the oil change frequency in months using command VP007 Oil change frequency in
months.
Check by reading parameter PR006 Oil change frequency in months.
C)Program the oil service interval in months using command VP009 Oil service interval: actual value in
months.
Check by reading parameter PR008 Oil service interval: actual value in months.
D) Program the fuel sender using command VP011 Fuel sender calibration.
There are 2 pieces of information to provide:
–Type of fuel (check by reading configuration LC049).
–Fuel level indicator:
–analogue (needle display),
–digital (bargraph display).
