2008 RENAULT SCENIC belt

83A-7
MR-372-J84-83A000$126.mif
V8
83A
INSTRUMENT PANEL
Fault finding - System operation
Instrument panel functions (entry level and mid-range versions):
The instrument panel allows:
–display by needle gauge of the following information:
–Vehicle speed
–Rev counter
–Fuel gauge
–Engine coolant temperature
–Management of 20 warning/indicator lights
–Alphanumeric display of the following information:
–Total and trip mileage
–Oil level
–Messages (68 messages)
–Keyless vehicle messages
–Warning messages
–Management of a multifunction buzzer:
The buzzer is used for the following functions:
–Indicating the operation of the direction indicators.
–Signalling that the lights have been left on.
–Indicating that the driver's or passenger's seat belts are not fastened when driving.
–Indicating that a door or the tailgate is not correctly closed.
–Signalling that the handbrake is on.
–Indicating the low fuel warning.
–Indicating that a speed has been exceeded, for Arabian versions, where an overspeed warning
is legally required.
–Indicating to the driver that the automatic locking when driving has been activated/deactivated.
The following buzzers can sound:
–Side lights on
–Direction indicators
–Management and trip computer display:
–Trip meter
–Fuel consumed
–Average fuel consumption
–Instantaneous fuel consumption
–Fuel range in kilometres and miles
–Distance travelled in kilometres and miles
–Average speed
–Oil service interval in kilometres
–Oil service interval in time
–Programmed speed (if the cruise control and speed limiter feature is present).
–Instrument panel dimmer: when the lights are on, the brightness of the instrument panel can be adjusted
using a button located on the instrument panel.
–In the event that the childproof lock system is not working, the buzzer will sound and a warning message
will appear on the instrument panel.
In vdiag 08 (with program version 040B) and vdiag 0C, the instrument panel can manage a personalised oil service
interval (known as the OCS) by detecting premature oil wear (depending on the engine). If the engine has this oil
wear detection management function, the oil service interval will initially be increased. The oil service interval could
however decrease more quickly if a “severe” type of driving (urban driving, diving in traffic jams, etc.) is detected by
the injection computer. The instrument panel will display a message to request that an oil service be performed
quickly, without necessarily displaying a warning message beforehand.
TDB ph2 (EG/MG)
Prog Version: 04xx
Vdiag No.: 08, 0C
MR-372-J84-83A000$126.mif

83A-11
MR-372-J84-83A000$252.mif
V8
INSTRUMENT PANEL
Fault finding - Configurations and programming83A
TDB ph2 (EG/MG)
Prog Version: 04xx
Vdiag No.: 08, 0C
2. PROGRAMMING:
A) Switch on the ignition.
B) Enter the VIN using command VP002 Enter VIN.
C) Program the mileometer using command VP010 Mileometer update.
Check by reading parameter PR009 Mileometer.
D) Enter the oil change frequency in kilometres using command VP006 Oil change frequency in km.
Refer to the information available on the Shared World Information database via RENAULT.NET
(on the maintenance programme page) to check the vehicle configuration.
Ignition on, engine off. Run command VP006 Oil change frequency in KM.
Enter the oil change interval in km.
Example of entry:
Using the CLIP numeric keypad,
enter 20 to display 20,000 km.
or
enter 30 to display 30,000 km.
LC no. CF no. Configuration Note:
LC060 CF002 Language settingCheck the language by using a message.
LC061 CF150 Cruise control/speed limiterIf the vehicle is equipped with a Cruise
Control-Speed Limiter function: check that the
cruise control or speed limiter indicator light
comes on when the cruise control/speed
limiter button is pressed.
LC064 CF158 Seat belt reminder buzzerThis function should only be inhibited on
authorised vehicles.
LC066 CF040 Particle filter
LC090 CF006 Vehicle speed signal systemIf the vehicle is equipped with ESP: check by
pressing the ESP OFF button that the Traction
control deactivated message appears.
If the vehicle is not equipped with ESP: check
that the ESP warning light does not come on
for 3 seconds when the ignition is switched
on.
LC106 CF198O.C.S. (vdiag 08 and program
version 040B and vdiag 0C)Refer to the information available on the
Shared World Information database via
RENAULT.NET (on the maintenance
programme page) to check the vehicle
configuration.

83A-21
MR-372-J84-83A000$441.mif
V8
83A
INSTRUMENT PANEL
Fault finding - Conformity check
MAIN COMPUTER STATUSES AND PARAMETERS
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application conditions: Ignition on, engine off.
Order FunctionParameter, Status
Check or ActionDisplay and notes Fault finding
1
SupplyPR110:Battery voltage11.5 V < PR110 < 16 VIn the event of a fault, consult
the interpretation of fault
DF019 Battery voltage.
2ET002:+ 12 V after
ignitionAbsent
PresentIn the event of a fault, refer to
the interpretation of status
ET002 + 12 V after ignition.
3
BrakeET097:Parking brakeApplied
ReleasedIn the event of a fault, consult
the interpretation of status
ET097 Parking brake.
4ET066:Brake fluid level
light alertIndicates the brake
fluid level.
PRESENT: Level too
low
ABSENT: Level correctIn the event of a fault, consult
the interpretation of status
ET066 Brake fluid level light
warning.
5Lighting PR111:Lighting dimmer
voltageIgnition on, dipped
headlights lit.
0.3 V < PR111 < 7 VIf the fault is still present,
contact Techline.
6Oil ET096:Oil pressure
contactOpen: indicator light off
Closed: indicator light
onIn the event of a fault, consult
the interpretation of status
ET096 Oil pressure contact.
7
Seat beltET098:Driver's seat belt
contactPresent (fastened)
AbsentIn the event of a fault, consult
the interpretation of status
ET098 Driver's seat belt
contact.
8ET062:Seat belt alarmOff
onIn the event of a fault, consult
the interpretation of status
ET098 Driver's seat belt
contact and of command
AC009 Instrument panel
indicator lights.
TDB_V08_CCONF /TDB_V0C_CCONFTDB ph2 (EG/MG)
Prog version: 04xx
Vdiag No.: 08, 0C
MR-372-J84-83A000$441.mif

83A-26
MR-372-J84-83A000$504.mif
V8
83A
INSTRUMENT PANEL
Fault finding - Status summary table
Tool status Diagnostic tool title
ET002+ 12 V after ignition
ET030ADAC scroll button
ET062Seat belt alarm
ET066Brake fluid level light alert
ET096Oil pressure contact
ET097Parking brake
ET098Driver's seat belt contact
TDB ph2 (EG/MG)
Prog Version: 04xx
Vdiag No.: 08, 0C
MR-372-J84-83A000$504.mif

83A-32
MR-372-J84-83A000$567.mif
V8
INSTRUMENT PANEL
Fault finding - Interpretation of statuses83A
TDB ph2 (EG/MG)
Prog Version: 04xx
Vdiag No.: 08, 0C
ET098
DRIVER'S SEAT BELT CONTACT
NOTESThere must be no present or stored faults.
Fasten the driver's seat belt: status ET098 Driver's seat belt contact should be
PRESENT and the instrument panel warning light should go out.
Test the multiplex network and the airbag (see 88B, Multiplexing and 88C, Airbag and pretensioners).
AFTER REPAIRCarry out another fault finding check on the system.
Deal with any other faults.
Clear the stored faults.
TDB_V08_ET098/TDB_V0C_ET098

83A-44
MR-372-J84-83A000$819.mif
V8
INSTRUMENT PANEL
Fault finding - Interpretation of commands83A
TDB ph2 (EG/MG)
Prog Version: 04xx
Vdiag No.: 08, 0C
AC009
INSTRUMENT PANEL WARNING LIGHTS
NOTESThere must be no present or stored faults.
Activate the instrument panel warning lights using command AC009 Instrument panel warning lights.
The indicator lights are all on, check that the lights are correct.
Check the condition and connection of the instrument panel 24-track grey connector.
If there is a repair method (see Technical note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair) repair the wiring, otherwise replace it.
Check the condition and connection of the 4-track seat belt warning module black connector.
If there is a repair method (see Technical note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair) repair the wiring, otherwise replace it.
Check the insulation, continuity and the absence of interference resistance on the following connections:
Instrument panel grey connector, track 16 Track 3 of the seat belt warning module
connector
Instrument panel grey connector, track 23 Track 4 of the seat belt warning module
connector
Instrument panel grey connector, track 12 Track 1 of the seat belt warning module
connector
Instrument panel grey connector, track 11 Track 2 of the seat belt warning module
connector
If there is a repair method (see Technical note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair) repair the wiring, otherwise replace it.
If the fault is still present, contact Techline.
AFTER REPAIRRepeat the conformity check from the start.