2008 PONTIAC G6 tow

As the switch is being pressed the windows and trunk
lid will open. The hardtop will automatically lower into the
trunk, and the trunk lid will close and latch. If the
engine is on, a chime will sound when the hardtop has
lowered completely. The Driver Information Center
(DIC) will display TOP MOVE COMPLT to signal the
procedure is complete. SeeDIC Warnings and
Messages on page 3-46for more information.After the hardtop has lowered completely, release the
switch. If you continue to press the switch for about
two seconds after the hardtop has completely lowered,
the windows will automatically close.
If pressure is released from the switch before the
hardtop cycle is complete, the cycle will stop and the
Driver Information Center (DIC) will display the
TOP NOT SECURE message. Always press and hold
the switch until a chime sounds, if the engine is on, and
the Driver Information Center (DIC) displays the TOP
MOVE COMPLT to signal the procedure is complete.
SeeDIC Warnings and Messages on page 3-46
for more information.
The hardtop will not operate if the vehicle has an
electrical failure. If an electrical failure occurs, see your
dealer/retailer for service.
If your vehicle has an electrical failure while operating
the hardtop, and must be towed to a dealer/retailer
for service, your vehicle should be towed by atbed with
the vehicle facing backwards. Consult your dealer/
retailer or professional towing service if you need to
have your disabled vehicle towed. SeeRoadside
Assistance Program on page 7-6.
2-48

As the switch is being pressed the hardtop will raise
from the trunk and move into place. The hardtop
and trunk lid will close and latch. If the engine is on, a
chime will sound when the hardtop has raised
completely. The Driver Information Center (DIC) will
display the TOP MOVE COMPLT message to signal the
procedure is complete. SeeDIC Warnings and
Messages on page 3-46for more information.After the hardtop has raised completely, release the
switch. If you continue to press the switch for about
two seconds after the hardtop has raised completely, the
windows will automatically close.
If pressure is released from the switch before the
hardtop cycle is complete, the cycle will stop and the
Driver Information Center (DIC) will display the
TOP NOT SECURE message. Always press and hold
the switch until a chime sounds, if the engine is on, and
the Driver Information Center (DIC) displays the TOP
MOVE COMPLT to signal the procedure is complete.
SeeDIC Warnings and Messages on page 3-46
for more information.
The hardtop will not operate if the vehicle has an
electrical failure. If an electrical failure occurs, see your
dealer/retailer for service.
If your vehicle has an electrical failure while operating
the hardtop, and must be towed to a dealer/retailer
for service, your vehicle should be towed by atbed with
the vehicle facing backwards. Consult your dealer/
retailer or professional towing service if you need to
have your disabled vehicle towed. SeeRoadside
Assistance Program on page 7-6.
2-51

Hazard Warning Flashers
The hazard warning ashers let you warn the police and
others that you have a problem. The front and rear
turn signal lamps will ash on and off.
The hazard warning
asher button is located
towards the center of
the instrument panel.
Press the button to make the front and rear turn signal
lamps ash on and off. Press the button again to
turn the ashers off.
While the hazard warning ashers are on, the turn
signals do not work.
The hazard warning ashers work no matter what
position the key is in, and even if the key is not in the
ignition switch.
Other Warning Devices
If you carry reective triangles, you can set them up at
the side of the road about 300 feet (100 m) behind
your vehicle.
Horn
Press near or on the horn symbols on the steering
wheel pad to sound the horn.
Tilt Wheel
A tilt and telescope wheel allows you to adjust the
steering wheel before you drive. Raise the steering
wheel to the highest level to give your legs more room
when you enter and exit the vehicle.
The lever that allows you to tilt and telescope the
steering wheel is located on the left side of the steering
column.
3-6

Turn and Lane-Change Signals
The turn signal has two upward (for right) and two
downward (for left) positions. These positions let you
signal a turn or a lane change.
To signal a turn, move the lever all the way up or down.
When the turn is nished, the lever returns automatically
to the normal position.
An arrow on the instrument
panel cluster ashes in the
direction of the turn or
lane change.
To signal a lane change, raise or lower the lever until
the arrow starts to ash. Hold it there until you complete
your lane change. The lever returns by itself when it
is released.
If the arrows ash rapidly or do not go on at all as you
signal a turn or lane change, a signal bulb could be
burned out and other drivers will not see your turn
signal.
Replace burned out bulbs to help avoid an accident.
Also, check the appropriate fuses. SeeFuses on
page 5-110.
Headlamp High/Low-Beam Changer
To change the headlamps from low beam to high beam,
push the turn signal/multifunction lever away from you.
This light comes on in the
instrument panel cluster if
the high beam lamps
are turned on while the
ignition is in ON/RUN.
To change the headlamps from high beam to low beam,
pull the turn signal lever toward you.
Flash-to-Pass
This feature lets you use your high-beam headlamps to
signal a driver in front of you that you want to pass.
To use it, pull the turn signal/multifunction lever toward
you until the high-beam headlamps come on, then
release the lever to turn them off.
3-8

When adding electrical equipment, be sure to follow the
proper installation instructions included with the
equipment.
Notice:Improper use of the power outlet can cause
damage not covered by your warranty. Do not
hang any type of accessory or accessory bracket
from the plug because the power outlets are
designed for accessory power plugs only.
Climate Controls
Climate Control System
The heating, cooling, and ventilation for your vehicle
can be controlled with this system. If your vehicle
has the remote start feature, the climate control system
functions as part of the remote start feature. See
Remote Keyless Entry (RKE) System Operation on
page 2-4.
Operation
9
(Fan):Turn the left knob clockwise or
counterclockwise to increase or decrease the
fan speed. The fan must be on to run the air conditioning
compressor.
To change the air delivery settings, turn the right knob
to select one of the following:
H(Vent):Turn the knob to this mode to direct air to
the instrument panel outlets.
)(Bi-Level):Turn the knob to this mode to direct half
of the air to the instrument panel outlets, and the
remaining air to the oor outlets. Some air may be
directed toward the side windows.
3-19

Brake System Warning Light
Your vehicle’s hydraulic brake system is divided into
two parts. If one part is not working, the other part can
still work and stop you. For good braking, though,
you need both parts working well.
If the warning light comes on, there is a brake problem.
Have your brake system inspected right away.
This light should come on briey when you start the
engine. If it does not come on then, have it xed so it will
be ready to warn you if there is a problem.
When the ignition is on, the brake system warning light
will also come on when you set your parking brake.
The light will stay on if your parking brake does
not release fully. If it stays on after your parking brake is
fully released, it means you have a brake problem.If the light comes on while you are driving, pull off the
road and stop carefully. You may notice that the pedal is
harder to push, or the pedal may go closer to the
oor. It may take longer to stop. If the light is still on,
have the vehicle towed for service. SeeTowing
Your Vehicle on page 4-25.
{CAUTION:
Your brake system may not be working
properly if the brake system warning light is
on. Driving with the brake system warning light
on can lead to an accident. If the light is still
on after you have pulled off the road and
stopped carefully, have the vehicle towed for
service. United States
Canada
3-34

This light comes on, as a check to show it is working,
when the ignition is turned ON/RUN but the engine is not
running. If the light does not come on, have it repaired.
This light also comes on during a malfunction in
one of two ways:
Light Flashing— A misre condition has been
detected. A misre increases vehicle emissions
and could damage the emission control system on
your vehicle. Diagnosis and service might be
required.
Light On Steady— An emission control system
malfunction has been detected on your vehicle.
Diagnosis and service might be required.
If the Light is Flashing
The following can prevent more serious damage to your
vehicle:
Reduce vehicle speed.
Avoid hard accelerations.
Avoid steep uphill grades.
If you are towing a trailer, reduce the amount of
cargo being hauled as soon as it is possible.
If the light stops ashing and remains on steady, see “If
the Light Is On Steady” following.If the light continues to ash, when it is safe to do so,
stop the vehicle. Find a safe place to park the vehicle.
Turn the ignition off, wait at least 10 seconds, and restart
the engine. If the light remains on steady, see “If the
Light Is On Steady” following. If the light is still ashing,
follow the previous steps and see your dealer/retailer
for service as soon as possible.
If the Light Is On Steady
You might be able to correct the emission system
malfunction by considering the following:
Did you recently put fuel into your vehicle?
If so, reinstall the fuel cap, making sure to fully install
the cap. SeeFilling the Tank on page 5-9. The
diagnostic system can determine if the fuel cap has
been left off or improperly installed. A loose or missing
fuel cap allows fuel to evaporate into the atmosphere.
A few driving trips with the cap properly installed should
turn the light off.
Did you just drive through a deep puddle of water?
If so, your vehicle’s electrical system might be wet. The
condition is usually corrected when the electrical system
dries out. A few driving trips should turn the light off.
3-39

Setting the Tone
(Bass/Midrange/Treble)
TONE (Bass/Midrange/Treble):Press and release the
tone until BASS, MID (midrange), or TREB (treble)
displays. Turn the ADJ (adjust) knob to increase or to
decrease the tone. The display shows the bass,
midrange, or treble level. If a station is weak or has
static, decrease the treble.
To adjust bass, midrange, or treble to the middle
position, select BASS, MID, or TREB. Then press and
hold the tone button for more than two seconds.
One beep sounds and the tone control adjusts to the
middle position.
To adjust all tone controls to the middle position, press
and hold the tone button while no tone control is
displayed. ALL CENTERED displays and a beep
sounds. The bass, midrange, and treble adjusts to the
middle position.
AUTO TONE (Automatic Equalization):Press to
select customized equalization settings designed
for country, jazz, talk, pop, rock, and classical.
The equalization setting last chosen appears on the
display when you rst press this button. Each time you
press this button, another equalization setting displays
and automatic tone or automatic equalization switches to
that preset equalization setting.To return to the manual mode, press the AUTO TONE
button until CUSTOM displays. The bass, midrange,
and treble can manually be adjusted using the tone
button.
Adjusting the Speakers (Balance/Fade)
BAL/FADE (Balance/Fade):To adjust the balance
between the right and the left speakers, push and
release the balance and fade button until BAL displays.
Turn the ADJ (adjust) knob to move the sound toward
the right or the left speakers.
To adjust the fade between the front and the rear
speakers, push and release the balance and fade button
until FADE displays. Turn the ADJ knob to move the
sound toward the front or the rear speakers.
To adjust balance or fade to the middle position, select
BAL or FADE. Then press and hold the balance and
fade button for more than two seconds. One beep
sounds and the speaker control adjusts to the middle
position.
To adjust both speaker controls to the middle position,
push and hold the balance and fade button while no
speaker control is displayed. ALL CENTERED displays
and One beep sounds.
3-57