2008 Peugeot 407 C ECU
[x] Cancel search: ECUPage 22 of 211
1
25
T y r e u n d e r - i n fl a t i o n
detection system warning
light
This indicates the absence or
malfunction of one or more
tyre pressure sensors or a system fault.
Consult a PEUGEOT dealer.
Electronic engine
immobiliser warning light
This indicates an electronic
engine immobiliser system
malfunction.
Consult a PEUGEOT dealer. Front brake pads wear
warning light
This indicates that the brake
pads are worn.
For your safety, have them replaced
by a PEUGEOT dealer.
Fuel tank cap warning light
(according to version)
With the engine running, this
indicates that the fuel tank
cap is incorrectly secured or
absent.
It comes on in orange if the vehicle
speed is below 6 mph (10 km/h) and
in red if the vehicle speed is above 6
mph (10 km/h).
Door/boot open warning
light
With the engine running, this
indicates that an access has
not been closed correctly.
An illustration on the multifunction
d i s p l a y i d e n t i fi e s t h e a c c e s s ( e s ) c o n -
cerned.
It comes on in orange if the vehicle
speed is below 6 mph (10 km/h) and
in red if the vehicle speed is above 6
mph (10 km/h). Air bags warning light
This indicates an air bag
fault.
Consult a PEUGEOT dealer.
Automatic headlamp
beam adjustment system
warning light
This indicates that the auto-
matic headlamp height ad-
juster is faulty.
Consult a PEUGEOT dealer.
Punctured tyre warning
light
This indicates that one or
more punctured tyres have
been detected.
A message on the multifunction display
i d e n t i fi e s t h e w h e e l ( s ) c o n c e r n e d .
It is linked with the STOP warning
light.
Stop immediately.
Change the damaged wheel and have
it repaired by a PEUGEOT dealer.
Engine oil pressure
warning light
This indicates that the engine
oil pressure is too low.
It is linked with the STOP warning
light.
Stop immediately if it comes on while
the engine is running.
If there is a lack of oil in the lubrication
circuit, top up the level and contact a
PEUGEOT dealer as soon as possible.
Page 60 of 211
3
58
Passenger air bag OFF
CHILD SEATS RECOMMENDED BY PEUGEOT
P E U G E O T o f f e r s a c o m p l e t e r a n g e o f r e c o m m e n d e d c h i l d s e a t s w h i c h a r e
secured using a three point seat belt :
Group 0: from birth to 10 kg
Group 0+: from birth to 13 kg
L1
" R O M E R B a b y - S a f e P l u s "
I n s t a l l e d i n t h e r e a r - f a c i n g p o s i t i o n
Groups 1, 2 and 3: from 9 to 36 kg
L2
" K I D D Y L i f e "
F o r t h e s a f e t y o f y o u n g c h i l d r e n ( f r o m 9 t o 1 8 k g ) , P E U G E O T r e c o m m e n d s use of the restraining cushion.
Groups 2 and 3: from 15 to 36 kg
L3
" R E C A R O S t a r t "
L4
" K L I P P A N O p t i m a "
From the age of 6 y e a r s
( a p p r o x i m a t e l y 2 2 k g ) , the booster is used on its own.
Page 101 of 211
7
91
Steering column air bag *
- Do not sit with your knees any nearer to the steering wheel than
necessary.
Front air bags
- Do not drive holding the steering
wheel by its spokes or resting your
hands on the centre part of the
wheel.
- Passengers must not place their feet on the fascia.
- Smoke as little as possible; de- ployment of the air bags can cause
burns or the risk of injury from a
cigarette or pipe.
- Never remove or pierce the steer- ing wheel or hit it violently.
* According to country.
Front side air bags
- Only put approved covers on the
seats. These will not hamper the
deployment of the side air bags.
Consult a PEUGEOT dealer.
- D o n o t fi x o r g l u e a n y t h i n g t o t h e seat backs. This could cause injury
to the chest or arms when the side
a i r b a g i n fl a t e s .
- Do not sit with the upper part of the body any nearer to the door than
necessary. Curtain air bags
- D o n o t fi x o r g l u e a n y t h i n g t o t h e
pillars or the roof. This could cause
injury to the head when the curtain
a i r b a g i n fl a t e s .
- Do not remove the grab handles in- stalled on the roof, they play a part
in securing the curtain air bags.
For the air bags to be fully ef-
fective, observe the following
safety rules:
- Wear a correctly adjusted seat belt.
- Sit in a normal upright position.
- Do not leave anything between the occupants and the air bags
(a child, pet, object...). This could
hamper the operation of the air
bags or injure the occupants.
- After an accident or if the ve- hicle has been stolen or broken
into, have the air bag systems
checked.
- All work on the air bag system is strictly forbidden unless it is car-
r i e d o u t b y q u a l i fi e d p e r s o n n e l o f
the PEUGEOT network.
- Even if all of the precautions men- tioned are observed, a risk of in-
jury or of slight burns to the head,
chest or arms, when an air bag is
deployed, cannot be ruled out. The
b a g i n fl a t e s a l m o s t i n s t a n t l y ( w i t h i n
a f e w m i l l i s e c o n d s ) t h e n d e fl a t e s
within the same time discharging
the hot gas via openings provided
for this purpose.
Page 114 of 211
9
104
Bonnet strut
Secure the strut in its housing to hold
the bonnet open.
Before closing the bonnet, replace the
strut in its clip.
OPENING THE BONNET
From inside: pull the handle on the
left-hand side under the fascia to-
wards you.
From outside: lift the catch and raise
the bonnet. To avoid any risk of burns, only
handle the bonnet strut by the
protective foam.
To close
Lower the bonnet and release it at the
end of its travel. Check that the bonnet
is properly locked.
Page 121 of 211
1010
110
After changing the wheel:
- have the tightening of the bolts and the tyre pressure of the spare wheel
checked as soon as possible.
-
have the punctured wheel repaired and
r e fi t i t t o t h e v e h i c l e a s s o o n a s p o s s i b l e .
- have the spare wheel checked and replace it in its boot recess.
Fitting a wheel
Position the wheel.
Tighten the bolts by hand.
Partly tighten the bolts using the
wheelbrace 1 .
Fold the jack 2 and remove it.
Fully tighten the bolts using the
wheelbrace 1 .
F o r v e h i c l e s w i t h a l l o y w h e e l s , r e fi t
the covers.
Put the tool holder back in position.
T h i s h e l p s t o k e e p t h e b o o t fl o o r i n
its correct position, to prevent any
d e f o r m a t i o n o f t h e fl o o r w h e n l o a d e d .
Tighten the spare wheel securing
strap to prevent noise and for your
safety in the event of impact.
Reminder: for your safety, always
change a wheel:
- on level, stable, non-slippery ground,
- with the handbrake applied,
- w i t h fi r s t o r r e v e r s e g e a r e n g a g e d (position P for the automatic gear-
box),
- never go underneath a vehicle which is supported only by a jack.
Tools available
The following tools are located in
the holder in the centre of the spare
wheel:
1. Wheelbrace. Permits removal of
the wheel trim and removal of the
wheel securing bolts.
2. Jack with integrated handle.
Permits raising of the vehicle.
3. Removable towing eye. See corre-
sponding section.
4. Bolt cover tool. Permits removal of
the bolt protectors (covers) on al-
loy wheels. Removal
For vehicles with alloy wheels, re-
move the covers using tool 4 .
Loosen the wheel bolts.
Place the jack 2 in one of the four
locations underneath the vehicle
(the nearest one to the wheel to be
changed).
Extend the jack 2 until its base is in
contact with the ground.
Unscrew the bolts and remove the
wheel.
Page 122 of 211
1010
111
Bolt covers
Alloy wheel bolts are covered by
chrome trims.
Use the yellow tool to remove the trims
before slackening the bolts.
Fitting the spare wheel
I f y o u r v e h i c l e i s fi t t e d w i t h a s t e e l
s p a r e w h e e l , w h e n fi t t i n g i t , i t i s nor-
mal when tightening the bolts to
notice that the washers do not come
into contact with the rim. The spare
wheel is secured by the cone shape
of each bolt.
VERY COLD CLIMATE SCREEN *
The very cold climate screen is a par-
t i a l r e m o v a b l e c o v e r w h i c h i s fi x e d
onto the air intake grille to prevent the
accumulation of snow due to direct
splashes.
O n c e i t h a s b e e n fi t t e d o n y o u r v e h i -
cle, it is imperative that it is removed
when the ambient temperature condi-
tions rise above 10°C again.
Consult a PEUGEOT dealer.
* According to country.
Special features of alloy wheels
Anti-theft bolts
Y o u r w h e e l s a r e fi t t e d w i t h a n t i - t h e f t
bolts (one per wheel), placed under
chrome trims which must be removed
using the yellow tool, before the bolts
are unscrewed using the anti-theft
socket and the wheel brace 1 .
Fitting snow tyres
I f y o u fi t s n o w t y r e s m o u n t e d o n s t e e l
wheels onto your vehicle, it is
essen-
tial to use special bolts available from
your PEUGEOT dealer.
Note: this anti-theft socket
was given to you on delivery
of your vehicle with the dupli-
cate keys. Make a careful note
of the code number engraved on the
head of the anti-theft socket. This will
enable you to obtain a duplicate anti-
theft socket from a PEUGEOT dealer.
You are advised to do the same for the
duplicate keys and not to leave the
c o n fi d e n t i a l c a r d i n t h e v e h i c l e .
Punctured tyre warning
light
Information on the instrument
panel:
T y r e u n d e r - i n fl a t i o n
detection system warning
light
T h e s e o r i g i n a l w h e e l s a r e fi t t e d w i t h a
pressure sensor (see paragraph "Tyre
u n d e r - i n fl a t i o n d e t e c t i o n " ) . T h e a l a r m
which detects the removal or absence
o f a w h e e l fi t t e d w i t h t h e i n d i c a t o r
sensor signals the anomaly. Have
the wheel repaired and checked by a
PEUGEOT dealer.
Page 123 of 211
1010
111
Bolt covers
Alloy wheel bolts are covered by
chrome trims.
Use the yellow tool to remove the trims
before slackening the bolts.
Fitting the spare wheel
I f y o u r v e h i c l e i s fi t t e d w i t h a s t e e l
s p a r e w h e e l , w h e n fi t t i n g i t , i t i s nor-
mal when tightening the bolts to
notice that the washers do not come
into contact with the rim. The spare
wheel is secured by the cone shape
of each bolt.
VERY COLD CLIMATE SCREEN *
The very cold climate screen is a par-
t i a l r e m o v a b l e c o v e r w h i c h i s fi x e d
onto the air intake grille to prevent the
accumulation of snow due to direct
splashes.
O n c e i t h a s b e e n fi t t e d o n y o u r v e h i -
cle, it is imperative that it is removed
when the ambient temperature condi-
tions rise above 10°C again.
Consult a PEUGEOT dealer.
* According to country.
Special features of alloy wheels
Anti-theft bolts
Y o u r w h e e l s a r e fi t t e d w i t h a n t i - t h e f t
bolts (one per wheel), placed under
chrome trims which must be removed
using the yellow tool, before the bolts
are unscrewed using the anti-theft
socket and the wheel brace 1 .
Fitting snow tyres
I f y o u fi t s n o w t y r e s m o u n t e d o n s t e e l
wheels onto your vehicle, it is
essen-
tial to use special bolts available from
your PEUGEOT dealer.
Note: this anti-theft socket
was given to you on delivery
of your vehicle with the dupli-
cate keys. Make a careful note
of the code number engraved on the
head of the anti-theft socket. This will
enable you to obtain a duplicate anti-
theft socket from a PEUGEOT dealer.
You are advised to do the same for the
duplicate keys and not to leave the
c o n fi d e n t i a l c a r d i n t h e v e h i c l e .
Punctured tyre warning
light
Information on the instrument
panel:
T y r e u n d e r - i n fl a t i o n
detection system warning
light
T h e s e o r i g i n a l w h e e l s a r e fi t t e d w i t h a
pressure sensor (see paragraph "Tyre
u n d e r - i n fl a t i o n d e t e c t i o n " ) . T h e a l a r m
which detects the removal or absence
o f a w h e e l fi t t e d w i t h t h e i n d i c a t o r
sensor signals the anomaly. Have
the wheel repaired and checked by a
PEUGEOT dealer.
Page 124 of 211
1010
112
CHANGING A FRONT BULB
Handle the bulbs with a dry cloth.
2 - Side lights : W 5 W (COOL BLUE
®).
Turn the access cap a quarter turn,
remove the bulb and change it.
3 - Direction indicators : PY 21 W
(DIADEM
®).
Turn the access cap a quarter turn,
Remove the bulb holder.
Change the bulb.
4 - Front fog lamps
: H11 - 55 W.
T h e h e a d l a m p s a r e fi t t e d w i t h p o l y c a r -
bonate glass with a protective coating. Do
not clean them with a dry or abrasive cloth,
nor with a detergent or solvent product.
E n s u r e t h a t t h e l i q u i d u s e d t o fi l l t h e
wash-wipe and headlamp wash reser-
voir is of good quality. Integrated direction indicator side
repeaters
Push the repeater forwards or
backwards and release it.
Unclip the repeater and change it.
Repeaters can be obtained from a
PEUGEOT dealer.
Front lights
In the engine compartment, remove
the cover secured by one or two but-
t e r fl y s c r e w s , a p l a s t i c r e t a i n e r c l i p a n d
two quarter turn screws.
1 - Dipped beam and main beam head-
lamps : D1S-35W xenon bulb.
WARNING: RISK OF
ELECTROCUTION Coloured bulbs (side lights
and direction indicators) must
be replaced with bulbs of iden-
t i c a l s p e c i fi c a t i o n a n d c o l o u r .
In certain climatic conditions
(low temperature, humidity),
condensation on the inside
surface of the headlamp glass
is normal; it disappears a few minutes
after the lights are switched on.
Xenon bulbs must be replaced by a
PEUGEOT dealer.