2008 Peugeot 207 Dag brake light

!
i
114
"Auto sequential" mode
In the automated mode, you can resume
control temporarily at any time using the
steering wheel controls.
The use of these controls permits man-
ual selection of the gears in situations
which require a more rapid change-
down than in the automated mode (ar-
rival at a roundabout, leaving a car park
with a steep gradient, overtaking...).
The gearbox engages the required gear if
the engine speed permits. AUTO remains
displayed on the instrument panel.
After a few minutes, the gearbox resumes
automatic control of the gears. "Snow" automated mode
In the automated mode, if the vehi-
cle detects poor grip, the gearbox will
change automatically to the "snow" au-
tomated mode.
Stopping the vehicle
Before switching off the engine, you can
change to position
N to be in neutral.
In this case, it is imperative that you
apply the handbrake to immobilise the
vehicle.
Reinitialisation
Following disconnection of the battery,
the gearbox must be reinitialised.

 Switch on the ignition. Operating fault
With the ignition on, if this warn-
ing light comes on and AUTO
fl ashes, accompanied by an au-
dible signal and a message on
the multifunction display, this indicates
a gearbox malfunction.
Have it checked by a PEUGEOT dealer.
It is compulsory to press the brake
pedal while starting the engine.
Never select neutral N while the
vehicle is moving.
Only engage reverse gear R when
the vehicle is immobilised, with
your foot on the brake pedal.
In all cases, it is imperative that you
apply the handbrake to immobilise
the vehicle.
If you press the accelerator pedal
beyond the point of resistance, the
gearbox selects the gear below to
permit sharper acceleration.

AUTO and  appear on the
instrument panel.

AUTO ,  and - appear on the
instrument panel.
 Select position N .

 Press the brake pedal.

 Wait approximately 30 seconds until

N or a gear appears on the instru-
ment panel.

 Release the brake pedal.
The gearbox is operational again.

115
"PORSCHE TIPTRONIC
SYSTEM" AUTOMATIC
GEARBOX
Four-speed automatic gearbox which
offers a choice between the comfort of
fully automatic operation, enhanced by
sport and snow programmes, or manual
gear changing.
Therefore, four driving modes are of-
fered:
- automatic operation for electronic
management of the gears by the
gearbox,
- sport programme for a more dy-
namic style of driving,
- snow programme to improve driv-
ing when traction is poor,
- manual operation for sequential
changing of the gears by the driver. Gear lever

P. Park.
- Immobilisation of the vehicle, hand- brake on or off.
- Starting the engine.

R. Reverse.
- Reversing manoeuvres, vehicle sta- tionary, engine at idle.

N. Neutral.
- Immobilisation of the vehicle, hand- brake on.
- Starting the engine.

D. Automatic operation.

M. +/- Manual operation with sequential
changing of the four gears.

 Press forwards to change up through
the gears.
or

 Press rearwards to change down
through the gears. Displays on the instrument panel
When you move the lever in the gate
to select a position, the corresponding
indicator light is displayed on the instru-
ment panel.

P. Park

R. Reverse

N. Neutral

D. Drive (Automatic driving)

S. Sport programme


. Snow programme

1, 2, 3, 4. Gear engaged during manu-
al operation

-. Invalid value during manual opera-
tion
Gear selection gate

1. Gear lever.

2. Button "S" (sport) .

3. Button "

" (snow). Foot on brake

 Press the brake pedal
when this indicator light
is displayed on the instru-
ment panel (e.g.: starting
the engine).

!i
117
Stopping the vehicle
Before switching off the engine, you
can engage position P or N to place the
gearbox in neutral.
In both cases, apply the handbrake to
immobilise the vehicle. Operating fault
When the ignition is on, the
lighting of this warning light, ac-
companied by an audible signal
and a message on the multi-
function display, indicates a gearbox
malfunction.
In this case, the gearbox switches to
emergency mode and is locked in 3rd
gear. You may feel a substantial knock
when changing from P to R and from N
to R . This will not cause any damage to
the gearbox.
Do not exceed 60 mph (100 km/h), local
speed restrictions permitting.
Contact a PEUGEOT dealer as soon as
possible.
If the battery is fl at and the lever is
in position P , it will not be possible
to change to another position.
Above all, do not force the lever as
this could damage the gearbox.
Manual operation

 Select position M for sequential
changing of the four gears.

 Push the lever towards the + sign to
change up a gear.

 Pull the lever towards the - sign to
change down a gear.

D disappears and the gears
engaged appear in succes-
sion on the instrument panel.
In the event of under-revving
or over-revving, the gear se-
lected fl ashes for a few seconds, then
the actual gear engaged is displayed.
It is possible to change from position D
(automatic) to position M (manual) at
any time.
When the vehicle is stationary or mov-
ing very slowly, the gearbox selects
gear M1 automatically.
The sport and snow programmes do not
operate in manual mode. If the lever is not in position
P ,
when the driver's door is opened or
approximately 45 seconds after the
ignition is switched off, an audible
signal is heard and a message ap-
pears.

 Return the lever to position P ;
the audible signal stops and the
message disappears.
It is only possible to change from one
gear to another if the vehicle speed and
engine speed permit; otherwise, the
gearbox will operate temporarily in au-
tomatic mode.
Invalid value during manual
operation
This symbol is displayed if a gear
is not engaged correctly (selec-
tor between two positions).

ii
138
Rear lights (Saloon)
1. Brake lights (P21 W).
2. Side lights (R 5 W).
3. Fog lamps (P21 W).
4. Direction indicators(PY 21 W amber).
5. Reversing lights (P21 W). Changing bulbs
These fi ve bulbs are changed from out-
side the boot :

 remove the light fi xing bolt,

 take out the light from the outside,

 disconnect the light connector,

 remove the light seal,

 press the four tabs and remove the
bulb holder,

 turn the bulb one quarter of a turn
and change it.
If the vehicle is fi tted with the JBL
audio system, on the right-hand
side, open the fl ap fi rst to gain ac-
cess to the fi xing bolt.
Amber coloured bulbs, such as the
direction indicators, must be re-
placed with bulbs of identical speci-
fi cation and colour. To refi t, carry out these operations in re-
verse order.

!
139
Changing the third brake light bulbs
(4 bulbs W 5 W)

 Press on the fi xing pins on each side
of the light.

 Take out the light from the outside.

 Turn the bulb holder which corre-
sponds to the faulty bulb one quar-
ter of a turn and remove it.

 Pull the bulb and change it. Changing the number plate light
bulbs (W 5 W)

 Insert a thin screwdriver in one of
the exterior holes of the lens.


Push it towards the outside to unclip it.

 Remove the lens.

 Pull the bulb and change it.
To refi t, carry out these operations in re-
verse order.
High pressure washing
When using this type of washing
on stubborn dirt, do not persist on
the headlamps, the lights and their
surrounds to avoid damaging their
varnish and their seal.

i
140
Rear lights (SW)

1. Brake lights (P21 W).

2. Side lights (R 5 W).

3. Direction indicators
(PY 21 W amber).

4. Fog lamps (P21 W).

5. Reversing lights (P21 W). Changing bulbs
These fi ve bulbs are changed from out-
side the boot:

 remove the access fl ap,

 disconnect the light connector,

 remove the light fi xing bolt,

 take out the light from the outside,

 press on the four tabs and remove
the bulb holder,

 turn the bulb a quarter of a turn and
change it.
To refi t, carry out these operations in re-
verse order.
Take care to engage the light in its
guides keeping it in the centreline of the
vehicle.
Tighten the fi xing bolt suffi ciently by
hand to guarantee the sealing of the
light.
Amber coloured bulbs, such as the
direction indicators, must be re-
placed with bulbs of identical speci-
fi cation and colour.

!
141
Changing the third brake light bulbs
(4 bulbs W 5 W)

 Remove the two light fi xing nuts.

 Take out the light from the outside.

 Press on the two tabs and remove
the bulb holder

 Pull the bulb and change it.
To refi t, carry out these operations in re-
verse order.
Tighten the fi xing bolt suffi ciently by
hand to guarantee the sealing of the
light. Changing the number plate bulbs
(W 5 W)

 Insert a thin screwdriver into one of
the exterior holes of the lens.

 Push it towards the outside to unclip it

 Remove the lens.

 Pull the bulb and change it.
High pressure washing
When using this type of washing
on stubborn dirt, do not persist on
the headlamps, the lights and their
surrounds to avoid damaging their
varnish and their seal.

144

Fuse N° Rating Functions

F8 20 A Audio equipment, audio/telephone, CD changer,
multifunction display, clock, steering wheel controls,
tyre under-infl ation detection, trailer fuse box.

F9 30 A Front 12 V socket, rear 12 V socket (SW).

F10 15 A Alarm siren, alarm control unit, directional
headlamps.

F11 15 A Diagnostic socket, low current ignition switch,
automatic gearbox control unit.

F12 15 A Rain/brightness sensor, amplifi er, trailer fuse box,
driving school module.

F13 5 A Engine fuse box, ABS relay, dual-function brake
switch, "2 Tronic" gearbox gear lever.

F14 15 A Instrument panel, seat belt warning lights bar,
headlamp adjustment, air conditioning, hands-free
kit, rear parking assistance control unit, air bags.

F15 30 A Locking and deadlocking.

F17 40 A Rear screen and exterior mirrors de-icing.

SH - PARC shunt.