2008 Peugeot 206 SW display

27
MULTIFUNCTION DISPLAYS
-
Setting the parameters
Press button 1 for two seconds to
access the settings. The informa-
tion lashes to show it is ready to be
modiied.
Then, individual presses on button 1
allow you to scroll through the vari -
ous data in the following sequence:
- language in which the information is displayed,
- unit of distance (kms or miles),
- unit of temperature (degrees Celsius or Fahrenheit),
- time format (12 then 24 hour mode),
- hour,
- minutes,
- year,
- month,
- day.
Pressing button 2 allows you to
change the information selected.
Maintain the pressure for rapid
scrolling.
After 7 seconds without operation,
the screen returns to the normal
display and the modiied data is
recorded.MONOCHROME DISPLAY B
This enables the following informa -
tion to be displayed:
- the time,
- the date,
- the outside temperature (this lashes when there is a risk
of ice),
- the radio displays,
- the status of the doors. The display shows you, by means
of a graphic, whether a door is
open,
- the warning messages
(e.g. "battery charge fault")
or information messages
(e.g. "fuel level low"), displayed
temporarily, can be cleared by
pressing button 1 or 2,
- the trip computer.

AUDIO EQUIPMENT
32 -
Manual station search
Press the "MAN" button.
Briely press button L or N to in-
crease or decrease the frequency
displayed.
By continuing to press the button in
the direction selected, you will obtain
continuous scrolling of the frequency.
The scrolling stops as soon as the
button is released.
Pressing the "MAN" button again
returns you to automatic station
search. Automatic storing of FM stations
in the memory (autostore)
Your radio automatically stores the
6 stations with the strongest signal in
FM
. These stations are stored in the
FMast waveband.
If it is not possible to ind 6 stations,
the remaining memories are empty.
Automatic station search
Manual storing of stations in the
memory
Select the station required.
Press one of the buttons "1" to "6"
for more than two seconds.
The sound stops then becomes audi-
ble again, conirming that the station
has been stored in the memory. Press and hold button
R
for more than two
seconds.
Recalling stations stored in the
memory
For each waveband, briely press
buttons "1" to "6" to recall the cor-
responding station.
Briely press button
L or N to search
for the station immediately above or
below. By continuing to press the
button in the direction selected, you
will obtain continuous scrolling of the
frequency.
The scrolling stops at the irst sta -
tion found as soon as the button is
released.
If the TA trafic programme is select -
ed, only stations broadcasting this
type of programme are selected.
Searching for a station occurs irst in
"LO" sensitivity (selection of the most
powerful transmitters) during scan -
ning of the waveband, then in "DX"
sensitivity (selection of the weakest
and most distant transmitters).
To make a direct search in "DX" sen-
sitivity, press button L or N twice.

33
AUDIO EQUIPMENT
-
RDSTrafic information programme
(TA) Regional following mode
When they are part of a network,

certain stations broadcast regional
programmes in the various areas
they serve. With regional following
mode you can keep listening to the
same programme.
Press the "RDS" button for more
than two seconds to switch the func -
tion on or off.
RDS station following
The display indicates the name of the
station selected. The radio is contin-
ually searching for the station which
has the best reception and which is
transmitting the same programme. Press the
"TA" button
to switch the function
on or off.
The multifunction dis-
play will show:
- "TA" if the function is selected,
- "(TA)" if the function is selected
but not available.
Any trafic information lash will be
given priority, whatever source you
are listening to (radio, CD or CD
changer).
If you wish to interrupt a message,
press the "TA" button; this switches
the function off.
Note: the volume of trafic informa -
tion is independent of the volume
of normal radio listening. You can
adjust it using the volume button.
The setting will be stored and will
be used when the next messages
are broadcast.
Briely press the "RDS"
button to switch the
function on or off.
The multifunction dis-
play will show:
- "RDS" if the function is selected.
- "(RDS)" if the function is
selected but not available.
Using the RDS (Radio Data
System) function on FM
Radio Data System allows you to
continue listening to the same sta-
tion, whatever frequency it is using
for the region you are going through.

COMFORT
44 -
AUTOMATIC AIR CONDITIONING
The air conditioning can only operate when the engine is running.
Automatic operation 2. Control by the AUTO programme
Press the "AUTO" button.
We recommend that you use
this mode: it provides opti-
mised automatic control of
all of the functions, passenger com -
partment temperature, air low, air
distribution and air recirculation, in
accordance with the comfort value
that you have chosen. This system is
designed to operate effectively in all
seasons, with the windows closed. Note:
for your comfort, the values
set when the engine is switched off
are retained on re-starting if the tem-
perature in the passenger compart-
ment has not changed signiicantly;
otherwise, operation resumes in au -
tomatic mode.
When the engine is cold, to prevent
too great a distribution of cold air, the
ventilation will only reach its optimum
level gradually.
On entering the vehicle, if the interior
temperature is much colder or warm -
er than is comfortable, there is no
need to change the value displayed
in order to reach the required level of
comfort. The system eliminates the
temperature difference automatically
and as quickly as possible.
Manual operation
If you wish, you can make a different
choice from that offered by the sys-
tem by changing a setting. The other
functions will still be controlled auto -
matically.
Pressing the AUTO button returns
the system to completely automatic
operation.
1. Temperature adjustment
The value indicated on the
display corresponds to a level
of comfort and not to a tem-
perature in degrees Celsius
or Fahrenheit.
Press the arrows 1 (up and down) to
change this value. A setting around
21 enables a comfortable tempera-
ture to be obtained.

45
COMFORT
-
3. Air conditioning On/Off
Press this button to stop air
cooling.
The symbol ECO is displayed.
Automatic operation of the air condi-
tioning is resumed when the button
is pressed again. The symbol A/C is
displayed.
4. Air distribution
Pressing this button several
times in succession enables
the air low to be directed in
turn towards:
- the windscreen
(de-icing or demisting),
- the windscreen and the
footwells,
- the footwells,
- the centre and side vents and the footwells,
- the centre and side vents. 5. Air low
Press buttons "+" and
"-" respectively to in-
crease or decrease
the air low.
6. Air intake/Air recirculation 7. Switching the system off
The OFF button switches
off all the functions of the
system.
Temperature-related comfort and
demisting are no longer guaranteed
but a slight low of air is maintained.
Pressing the OFF, AUTO , or "vis-
ibility" button again reactivates the
system with the values set before it
was switched off.
Note: if you wish to cut off the low
of air completely, press the air intake
button 7.
Press this button for recir-
culation of the interior air.
Recirculation, shown on the
display, enables the pas
-
senger compartment to be insulated
from exterior odours and smoke.
Avoid prolonged recirculation of interior
air (risk of condensation and deteriora-
tion of the air quality).
Press the button again to resume
automatic management of the intake
of air.
Notes
To prevent condensation on the in-
side of the vehicle in cold or wet
weather, you are advised to avoid
using the
ECO mode.
To guarantee correct operation of
your air conditioning system, we also
recommend that you have it checked
regularly.

57
ACCESS
-
KEYS
The keys allow you to switch on the
ignition and independently oper-
ate the passenger air bag disarming
switch and the steering lock. Locating your vehicle
To locate your vehicle, if you have
locked it, in a car park:
F
press button A, the courtesy
lights come on and the direction
indicators lash for a few
seconds.
Changing the remote control
battery
Battery ref.: CR2016/3 volts.
Warning that the battery is lat is given
by an audible signal accompanied by
the message "Remote control bat-
tery low" on the multifunction display.
To replace the battery, remove the
screw then unclip the casing using a
coin at the ring.
If the remote control does not work
after the battery has been changed,
reprogramme the remote control.
Key in ignition
A buzzer sounds on opening the
driver’s door, if the key has been left
in the ignition. Programming the remote
control
F
Switch off the ignition.
F Switch the ignition on again.
F Press button A immediately for a
few seconds.
F Switch off the ignition and
remove the remote control
key from the ignition lock. The
remote control is now working
again.
Without central locking/
unlocking by hand
The keys also allow you to unlock/
lock the front doors, the boot and the
fuel iller cap.
With central locking/
unlocking
The keys allow you to lock or unlock
all of the doors and the tailgate, from
the front doors.
If one of the doors or the tailgate is
open, the central locking does not
work. With central locking/
unlocking via the remote
control
Press button
A to lock the vehicle.
This is conirmed by ixed lighting of
the direction indicators for approxi-
mately two seconds.
Press button B to unlock the vehicle.
This is conirmed by the rapid lash -
ing of the direction indicators.
Avoid pressing the buttons of your
remote control out of range of your
vehicle. You risk causing it not to
work and the remote control would
then have to be reprogrammed (see
corresponding section).

ACCESS
60 -
CHILD SAFETY LOCK
On each rear door this prevents
opening of the door from the inside.
Turn switch 1 an eighth turn (45 de-
grees) using the ignition key.
Automatic central locking of the
doors
The doors can lock automatically
when you are driving (at a speed of
more than 6 mph (10 km/h)).
Above 6 mph (10 km/h), press but
-
ton B briely to unlock the doors tem -
porarily.
You can activate or deactivate this
function. To switch off
Press and hold button
B.
Notes: if one of the doors is open,
locking from the inside and automatic
central locking are not possible.
If the boot is open, automatic central
locking of the doors is possible.
To switch on
Press and hold button
B.
Activation of the function is accom-
panied by an audible signal and a
message on the multifunction display.The message is displayed each time
the vehicle is started.

VISIBILITY
64 -
"Follow me home" lighting
When you leave your vehicle, the
side lights and dipped headlamps
can be left on for approximately
30 seconds.
To do this:
- place the key in the STOP
position,
- place the lights stalk in the 0 position,
- lash the headlamps,
- get out of the vehicle and lock it.AUTOMATIC SWITCHING ON
OF LIGHTS
The side lights and dipped beam
headlamps switch on automatical -
ly if the light is poor and when the
windscreen wipers operate continu -
ously and switch off when the light
becomes bright enough or the wind -
screen wipers are switched off.
In foggy weather or in snow, the
brightness sensor can detect suf-
icient light, the lights will not
come on automatically. If neces-
sary, the dipped headlamps must
be switched on manually.
This function is active when the ve -
hicle is supplied to the customer.
To disarm or activate the function:
- Place the key in the accessories position (1st notch),
- Place the lights stalk in the AUTO/0 position,
- Press the end of the lights stalk for more than four seconds.
Do not cover the brightness sen-
sor, coupled with the rain sensor,
located in the centre of the wind-
screen, behind the interior mirror.
It is used for automatic switching
on of the lights. Operating check
In good or rainy weather,
both day and night, the
front fog lamps and the
rear fog lamp are dazzling
and are prohibited.
Do not forget to switch them off
when they are no longer needed.
Direction indicators
(lashers) Left: downwards.
Right: upwards. Disarming
The disarmed function is accompa-
nied by an audible signal.
When the driver uses the manual
lighting controls, the function is tem
-
porarily disarmed.
If the brightness sensor does not
function correctly, the lights come
on accompanied by an audible signal
and a message on the multifunction
display.
Consult a PEUGEOT dealer.
Activation
The activated function is accompa-
nied by an audible signal and a mes-
sage on the multifunction display.