2008 PEUGEOT 1007 ignition
[x] Cancel search: ignitionPage 74 of 189
4
75
Make a careful note of the
number on each key. The
key number is coded on the
label attached to the key.
If the keys are lost, a PEUGEOT
dealer can rapidly supply you with
new keys.
The high frequency remote con-
trol is a sensitive system; do not
operate it while it is in your pocket
as there is a possibility that it may
unlock your vehicle, without you
being aware of it.
The remote control does not ope-
rate when the key is in the ignition,
even when the ignition is switched
off, except for reprogramming.
Do not operate the deadlocking
function if there is anyone inside
the vehicle.
Driving with the doors locked may
make access to the passenger
compartment by the emergency
s e r v i c e s m o r e d i f fi c u l t i n a n e m e r -
gency.
As a safety precaution (with chil-
dren on board), remove the ignition
key when you leave the vehicle,
even for a short time.
Do not repeatedly press the button
of your remote control out of range
and out of sight of your vehicle.
You run the risk of stopping it from
working and the remote control
would have to be reprogrammed.
When purchasing a second-hand
vehicle, have the key codes memo-
rised by a PEUGEOT dealer to en-
sure that the keys in your posses-
sion are the only ones which can
start the vehicle.
Do not throw the remote
control batteries away, they
contain metals which are
harmful to the environment.
Take them to an approved collection
point.
D o n o t m a k e a n y m o d i fi c a t i o n s t o
the electronic engine immobiliser
system.
Page 75 of 189
4
76
ALARM
The alarm offers two types of
protection.
- external ; the alarm sounds if
one of the doors, the bonnet
or the tailgate is opened ,
- internal ; the alarm sounds
if there is air movement in
the passenger compartment
(a broken window or movement
within the car).
T h e a l a r m a l s o h a s a n a n t i - t a m p e r
function.
If there is an attempt to tamper with
the following equipment:
- t h e w i r e s t o t h e s i r e n o r t h e control unit, the siren sounds
a c c o m p a n i e d b y fl a s h i n g o f t h e
direction indicators.
- t h e b a t t e r y , t h e s i r e n s o u n d s . Complete setting and
disarming of the alarm
Complete disarming of the alarm
Press the unlocking button on the
remote control.
T h e d i r e c t i o n i n d i c a t o r s fl a s h f o r
two seconds.
The red indicator light on the switch
1 goes out.
Note: if the indicator light continues to
fl a s h a f t e r d e - a c t i v a t i o n o f t h e a l a r m ,
it is a sign that the alarm has been
triggered during your absence. The
fl a s h i n g w i l l s t o p w h e n t h e i g n i t i o n i s
switched on.
When the alarm is set,
if a door, the tailgate or
the bonnet is not closed
correctly, the siren sounds
for a moment. If the vehicle is closed
correctly in the following 45 seconds,
the alarm is set. In all cases, the
alarm is set after 45 seconds. Automatic setting
The alarm is set automatically
2 minutes after the last door or the
boot is closed.
To prevent the alarm being triggered
when a door or the boot is opened,
the remote control unlocking button
must be pressed again.
Locking the vehicle without
alarm
To lock the vehicle without activating
the alarm (for example when washing),
insert the key in the lock, then lock it.
Complete setting of the alarm
Switch off the ignition and get out
of the vehicle.
Lock or deadlock the vehicle.
The direction indicators light for
two seconds.
The red indicator light on the switch 1
fl a s h e s o n c e a s e c o n d .
5 seconds later, external protection
is set.
45 seconds later, internal protection
is set.
Note: when the alarm is triggered,
the siren sounds for thirty seconds.
However, after the siren stops, the
alarm remains set.
Page 76 of 189
4
77
Selection of the type of
protection Remote control failure
Unlock the doors using the key.
Open the door.
The alarm is triggered.
Switch on the ignition.
The electronic engine immobiliser
system recognises the key.
The siren stops and the alarm is
disarmed.
D o n o t m a k e a n y m o d i -
fi c a t i o n s t o t h e a l a r m
system, this could result in
malfunctions.
To de-activate external protection
only
Press the unlocking button on the
remote control.
T h e d i r e c t i o n i n d i c a t o r s fl a s h f o r t w o
seconds.
The red indicator light on the switch
1 goes out. Work on the battery
The alarm must not be set when the
battery is disconnected. Otherwise,
the siren will sound.
After reconnecting the battery:
- l o c k o r d e a d l o c k , t h e n u n l o c k
the vehicle using the remote
control,
- t h e a l a r m w i l l b e o p e r a t i o n a l again the next time the vehicle
is locked or deadlocked.
To set the alarm to external
protection only
If you want to leave a window partially
open, or a pet inside the vehicle, you
need to select external protection
only:
- s w i t c h o f f t h e i g n i t i o n ,
- w i t h i n t h e n e x t t e n s e c o n d s ,
press the control button 1 until
the warning light comes on
continuously,
- g e t o u t o f t h e v e h i c l e ,
- l o c k o r d e a d l o c k t h e v e h i c l e ,
- t h e d i r e c t i o n i n d i c a t o r s l i g h t f o r two seconds,
- t h e r e d i n d i c a t o r l i g h t o n t h e switch 1 fl a s h e s o n c e a s e c o n d .
Page 77 of 189
4
78
ELECTRIC WINDOWS
1. Driver’s electric window
switch.
2. Passenger electric window
switch.
One-touch electric window
with safety auto-reverse
You have two options: - Manual mode:
Press or pull switch 1 gently.
The window stops as soon
as the switch is released.
- Automatic mode:
Press or pull switch 1 f u l l y . T h e w i n -
dow opens or closes completely
when the switch is released.
Pressing the switch again stops the
movement of the window.
Note: the electrical functions of
t h e o n e - t o u c h e l e c t r i c w i n d o w s a r e
deactivated approximately one minute
after the ignition is switched off.
Safety auto-reverse
In automatic mode, when the window
rises and meets an obstacle, it stops
and partially lowers again.
In the case of unwanted
opening of the window on
closing or if the window will
not rise, lower it completely
and raise it again immediately, by
p u l l i n g t h e s w i t c h u n t i l t h e w i n -
dow closes completely. Continue to
press the switch for approximately
one second after closing.
The safety auto-reverse function is not
operational during these operations.
You can close all of the
windows using the remote
control when locking
( r e f e r t o t h e s e c t i o n " A c c e s s -
§ Remote control key").
The electric window switches are not
active when the door concerned is
open.
The movement of a window stops if
the door is opened. A second action
on the electric window switch will
only be taken into account when the
door is closed. Always remove the key from
the ignition when leaving
the vehicle, even for a short
time.
I n t h e e v e n t o f c o n t a c t w h e n o p e r a -
ting the windows, you must reverse
the movement of the window. To do
this, press the switch concerned.
When the driver operates the
passenger window switches, he must
ensure that no one is preventing
correct closing of the window.
The driver must ensure that
passengers use the electric windows
correctly.
Be aware of children when operating
the windows.
Page 79 of 189
4
80
Automatic central locking
The doors can lock automatically
when you are driving (at a speed of
more than 6 mph (10 km/h).
You can activate or deactivate this
function. Driving with the doors locked
may make access to the
passenger compartment by
the emergency services more
d i f fi c u l t i n a n e m e r g e n c y .
Activation
With the ignition on, press and hold
button A .
A c t i v a t i o n o f t h e f u n c t i o n i s a c c o m -
panied by an audible signal and a
message on the multifunction display.
Deactivation
With the ignition on, press and hold
button A .
Deactivation of the function is
accompanied by an audible signal
and a message on the multifunction
display.
"Door open" alert -
when the vehicle is moving,
by lighting of the "door open"
warning light, accompanied by
an audible signal and a message
on the multifunction display for a
few seconds.
Opening/Closing using the
remote control
Press button C or D to open or close
the left or right door.
The opening and closing of the
door is accompanied by an audible
signal.
2nd press on button C or D during
opening/closing interruption of the
movement.
3rd press on button C or D m o v e -
ment of the door in the opposite
direction.
You are advised to use the
r e m o t e c o n t r o l o r t h e c o n -
trols as much as possible.
Opening/Closing from the front
Press switch
B to open or close the
corresponding door.
Choosing the movement of the door
using the controls:
- p u l l opens the door,
- p u s h closes,
- s e c o n d p r e s s stops the
movement,
- t h e c o n t r o l s d o n o t f u n c t i o n above 3 mph (5 km/h).
If a door or the boot is not
closed properly, you are
warned:
- when the engine is running,
by lighting of the "door open"
warning light, accompanied by
a message on the multifunction
display for a few seconds.
Page 84 of 189
4
84
PANORAMIC SUNROOF
This sunroof is a panoramic assembly
which provides maximum brightness
a n d v i s i b i l i t y i n t h e p a s s e n g e r c o m -
partment.
It consists of two parts:
- a fi x e d r e a r p a r t ,
- a m o v i n g f r o n t p a r t .
Each part has an independent
manual shutter.
The sunroof is controlled electrically
by a dial with 9 opening positions. Operation
To open: turn the dial to the left
(nine possible settings).
Once the roof is open, the front
shutter cannot be closed.
To close: return the control to the
initial position "O" . Reinitialisation
F o l l o w i n g r e c o n n e c t i o n o f t h e b a t -
tery, in the event of a malfunction or
in the event of unwanted opening of
t h e r o o f o n c l o s i n g , t h e s a f e t y a u t o -
reverse must be reinitialised:
- p l a c e t h e d i a l i n t h e f u l l y c l o s e d
position (initial position "O" ),
- p r e s s t h e d i a l i m m e d i a t e l y ,
- c o n t i n u e t o p r e s s u n t i l t h e r o o f is fully closed.
Always remove the ignition
key when leaving the vehicle,
even for a short time.
In the event of contact during operation
of the roof, the movement of the roof
must be reversed. To do this, operate
the control concerned.
When the driver operates the roof
control, he must ensure that no one
is preventing the roof from closing
correctly.
The driver must ensure that the
passengers use the sunroof correctly.
Be aware of children when operating
the roof.
Check that the slides are clean
to ensure that the sunroof slides
correctly.
Safety auto-reverse
When the roof meets an obstacle
while closing, it partially opens
again.
You can close the sunroof
using the remote control
when locking (refer to the
corresponding chapter).
The safety auto-reverse function
is not operational during this
operation.
Page 86 of 189
5
86
LIGHTS STALK
Lights off Automatic switching on
of lights.
Side lights Dipped/main beam
headlamps Dipped/Main beam change
Pull the stalk fully towards you.
Front fog lamps and rear fog
lamp
Rotate the ring
B or C forwards to
switch on and backwards to switch
off. The status is displayed by the in-
dicator light on the instrument panel.
V e h i c l e s fi t t e d w i t h a r e a r f o g
lamp (ring B)
Rear fog lamp
V e h i c l e s fi t t e d w i t h f r o n t f o g
lamps and a rear fog lamp (ring C) Front fog lamps (1st rotation
of the ring forwards)
These operate with the side lights
and dipped headlamps.
Lights on
With the ignition off, a buzzer sounds
when the driver’s door is opened, if
you have left your lights on.
If the dipped headlamps remain
on, with the ignition off, they will be
switched off automatically after thirty
minutes maximum to prevent dis-
charging of the battery.
This can only operate with the dipped
and main beam headlamps.
Front and rear lights
Selection is by turning ring
A .
Page 92 of 189
5
90
W i n d s c r e e n w a s h
Pull the wiper stalk towards you. The
windscreen wash, then the wind-
screen wipers, operate for a speci-
fi e d t i m e .
L o w w a s h - w i p e / h e a d l a m p w a s h
fl u i d l e v e l
O n v e h i c l e s fi t t e d w i t h h e a d l a m p
washers, this is indicated by an audi-
ble signal or a message on the multi-
function display.
This information is given each time
the front or rear wash-wipe control is
o p e r a t e d , u n t i l t h e r e s e r v o i r i s fi l l e d .
W h e n y o u s t o p , fi l l t h e w a s h - w i p e /
headlamp wash reservoir or have it
fi l l e d . Do not cover the rain sen-
sor located on the wind-
screen behind the interior
mirror.
When using an automatic car wash,
switch off the ignition.
In winter, it is advisable to wait for the
windscreen to completely clear of ice
before operating the automatic wipe.
R e a r w i n d s c r e e n w i p e r
Turn ring A t o t h e fi r s t n o t c h
for intermittent wiping.
When reverse gear is engaged, if the
windscreen wipers are in operation,
the rear wiper will start wiping.
Turn ring A p a s t t h e fi r s t
notch; the windscreen wash
then the windscreen wiper
o p e r a t e f o r a fi x e d p e r i o d .
A u t o m a t i c w i n d s c r e e n w i p e r s
In
AUTO mode, the windscreen wip-
ers operate automatically and adapt
their speed to the intensity of the
rainfall .
Activation
Activation of the function is accom-
panied by a message on the multi-
function display.
T h e a u t o m a t i c w i n d s c r e e n w i p e r s
function must be reactivated if the
i g n i t i o n h a s b e e n s w i t c h e d o f f f o r
m o r e t h a n o n e m i n u t e , b y p r e s s -
i n g t h e s t a l k d o w n w a r d s .
Deactivation
Deactivation of the function is ac-
companied by a message on the
multifunction display.
The function is deactivated when the
windscreen wipers stalk is moved to
position I , 1 or 2 .
In the event of malfunction of the
automatic windscreen wipers, the
windscreen wipers will operate in in-
termittent mode.
Contact a PEUGEOT dealer to have
the system checked.
R e a r w i n d s c r e e n w a s h To activate or deactivate
this function, go to the
multi-function display
c o n fi g u r a t i o n m e n u .
I f t h e r e i s a s i g n i fi c a n t a c -
cumulation of snow or ice
and when using a bicycle
carrier on the tailgate, deactivate the
automatic rear wiping by going to the
m u l t i f u n c t i o n d i s p l a y c o n fi g u r a t i o n
menu.
Special position of the front
w i n d s c r e e n w i p e r
In the minute following switching off
of the ignition, any action on the stalk
positions the wipers in the centre of
the windscreen.
This action enables you to position
the wiper blades for winter parking,
cleaning or replacement (See corre-
sponding section).
To park the wipers after this has
been done, switch on the ignition and
operate the stalk.