2008 PEUGEOT 1007 brake
[x] Cancel search: brakePage 123 of 189
9
117
Parking the vehicle
- If possible, park the vehicle on level, stable and non-slippery
ground.
- It is imperative that you ensure that the occupants get out of the
vehicle and wait in a safe loca-
tion.
- Apply the handbrake, switch off t h e i g n i t i o n a n d e n g a g e fi r s t o r
reverse gear (position R for the
"2 Tronic" gearbox).
CHANGING A WHEEL
1. Jack with integrated handle.
2. Chock.
3. Wheelbrace.
4. Extension.
5. "Bolt cover" tool.
6. Removable towing eye. Access to the spare wheel and
the jack
The wheel is located outside the ve-
h i c l e , u n d e r t h e r e a r fl o o r , s u p p o r t e d
by a metal carrier.
- Unclip the cover to gain access
to the spare wheel carrier retain-
ing bolt, located on the inside
near the closing system.
- Using the wheelbrace 3 and the
extension 4 , slacken the spare
wheel carrier retaining bolt.
- Lift the carrier to release the hook rearwards, then lower it.
- Remove the spare wheel and the box.
- Remove the jack 1 from the box.
Tools provided
The jack is stored in a box in the cen-
tre of the spare wheel. The chock is
fi x e d o n t h e s i d e o f t h e b o x .
The other tools are stored in a case
in the left boot trim.
Note: i f y o u r v e h i c l e i s fi t t e d w i t h a
towbar, the case is stored in the left
s t o r a g e t r a y ( l o c a t e d i n t h e fl o o r o f
the rear footwell).
Page 124 of 189
9
118
Removing a wheel
-
Place the chock 2 (integrated with the
box) at the rear of the wheel diagonal-
ly opposite the wheel to be changed.
- Remove the wheel trim, using the wheelbrace 3 , by pulling at
the valve passage hole.
-
Remove the chrome-plated bolt
covers and the plastic cover from
the bolts using the "bolt cover" tool 5
(Special features of alloy wheels).
- Slacken the wheel bolts.
- Place the jack 1 under one of the
four locating points A on the sub-
frame closest to the wheel to be
changed. Ensure that the entire
surface of the jack base plate is
in contact with the ground.
-
Extend the jack, completely unscrew
the bolts and remove the wheel.
Refitting the wheel
- Position the wheel on the hub.
- Lightly pre-tighten the bolts us- ing the wheelbrace 3 .
-
Compress the jack 1 and release it.
- Fully tighten the bolts using the
wheelbrace.
- Replace the trim, starting at the valve passage hole, and press it
on using the palm of the hand.
For your safety, always
change a wheel:
- Stow the tools in the case, then
put it back in the left boot trim.
T h e j a c k a n d t h e t o o l k i t a r e s p e c i fi c
to your vehicle. Do not use them for
other purposes.
Replacing the wheel in the
carrier
- Replace the jack 1 in the box.
- Replace the box in the wheel.
- Replace the wheel in the carrier.
- Lift the wheel then the carrier and reposition the hook.
- Do not forget to fully tighten the spare wheel carrier retaining bolt. After changing the wheel
- Have the tightening of the bolts
and the pressure of the spare
tyre checked as soon as possi-
ble by a PEUGEOT dealer.
-
Do not exceed its maximum autho-
rised speed: 50 mph (80 km/h).
- Have the punctured tyre repaired and replace it on the vehicle as
soon as possible.
- 15 and 16 inch punctured wheels cannot be placed in the carrier.
- on level, stable and non-slippery
ground,
- with the handbrake applied,
- w i t h fi r s t o r r e v e r s e g e a r e n g a g e d (position R for the "2 Tronic"
gearbox),
- with the vehicle chocked,
- never go underneath a vehicle raised using a jack (use an axle
stand).
Page 128 of 189
9
122
Rear lights
1. Brake/side lights
(P21 W/5 W).
2. Direction indicators
(P21 W).
3. Reversing light
(P21 W), left side.
Fog lamp (P21 W), right side.
These 4 bulbs are changed by re-
moving the light:
R e m o v e t h e a c c e s s fl a p i n t h e
corresponding boot side trim to
access the light,
R e m o v e t h e t w o l i g h t fi x i n g n u t s
inside the boot,
Unclip the harness,
Remove the light pressing on the
retaining tabs,
Remove the seal,
Remove the bulb holder moving
aside the two tabs A ,
Turn the bulb a quarter of a turn,
Remove the bulb and change it.
Note: if necessary, use the wheel-
brace to remove the nuts.
W h e n r e fi t t i n g , p r o c e e d i n t h e r e -
verse order and take care to position
the bulb holder, the seal and the light
correctly. Third brake light
(4 W 5 W bulbs)
Using a 10 mm box spanner, un-
s c r e w t h e 2 fi x i n g n u t s A .
Release the lamp unit by push-
ing it outwards.
Disconnect the connector and
the rear wash-wipe pipe.
Turn the bulb holder a quarter of
a turn and remove it.
Remove the bulb and change it.
W h e n r e fi t t i n g , p r o c e e d i n t h e r e v e r s e
order and ensure that the lamp unit
seal and the rear wash-wipe pipe have
been put back in place correctly.
Do not tighten the nuts more than is
necessary at the risk of breaking the
light.
Number plate lights (W 5 W)
Insert a thin screwdriver into one
of the external holes of the lens.
Push it outwards to unclip it.
Remove the lens.
Remove the bulb and change it.
Page 131 of 189
9
124
Fuse N° Rating
Functions
1 15 A Rear wiper.
3 5 A Air bags and pre-tensioners control unit.
4 10 A Diagnostic socket - Clutch switch - Steering wheel angle sensor
-
P a r t i c l e e m i s s i o n fi l t e r p u m p .
5 30 A Electric windows - Sunroof.
6 - Not used.
7 5 A Courtesy light - Glove box light.
8 20 A T y r e u n d e r - i n fl a t i o n d e t e c t i o n c o n t r o l u n i t - F o l d i n g o f t
h e e l e c t r i c m i r r o r s - A l a r m s i r e n -
Multifunction display - Alarm control unit - Audio equipment - Aud io/telephone.
9 30 A Audio equipment - Lighter/12 V socket (100 W max.).
10 15 A Steering wheel controls.
11 15 A Diagnostic socket - Low current ignition switch - Motorised strik ers.
12 15 A Air bags and pre-tensioners control unit - Rain/brightness sens or.
13 5 A ABS relay - Speed sensor - Engine Fuse Box - "2 Tronic" gear lever - Brake switch.
14 15 A Parking assistance control unit - "Sesame" doors control unit and swit
ches -
Instrument panel - Seat belt warning lights bar - Air condition ing control panel -
Headlamp adjustment - Hands-free kit.
15 30 A Locking - Deadlocking - Unlocking.
17 40 A Rear screen and exterior mirrors demisting.
SH - PARC shunt.
Page 133 of 189
9
126
Fuse N° Rating
Functions
1 20 A Engine control unit and fan assembly control supply - Injection
control unit (Diesel) -
I n j e c t i o n p u m p ( D i e s e l ) - A i r h e a t i n g s o l e n o i d v a l v e s ( D i e s e l ) - A i r fl o w s e n s o r ( D i e s e l ) .
2 15 A Horn.
3 10 A Front and rear wash-wipe pump.
4 20 A Headlamp wash pump.
5 15 A Fuel pump (petrol).
6 10 A Power steering control unit - Water in diesel sensor - Vehicl e speed sensor.
7 10 A Switching and protection unit (Diesel) - Engine coolant l evel detector (Diesel).
8 25 A Starter.
9 10 A ABS/ESP control unit - ABS cut-off relay - Brake switch.
10 30 A Engine control unit actuators (petrol: ignition coils, oxygen
sensors, injectors,
purge canister and variable timing solenoid valves, controlled t hermostat)
( D i e s e l : i n j e c t i o n c o n t r o l u n i t , a i r fl o w s e n s o r , i n j e c t i o n p u m p , d i e s e l h i g h p r e s s u r e
regulator, EGR and Turbo pressure regulation solenoid valves) - Blow-by heaters -
Diesel heater.
11 40 A Air blowers.
12 30 A Windscreen wipers (low/high speed).
13 40 A (Ignition positive) Built-In Systems Interface.
14 - Not used.
15 10 A Right main beam headlamp.
16 10 A Left main beam headlamp.
17 15 A Left dipped headlamp.
18 15 A Right dipped headlamp.