Page 49 of 194
3
52
4 - Access to the rear seats
If necessary, detach the seat belt
from the handle and position it along
the door pillar.
Lift control A with one hand and
guide the movement of the seat for-
wards with the other hand (keeping
the control in the lifted position).
The driver has a courtesy handle B ,
located on the inner side of the pas-
senger seat, for tilting the seat to
allow a child access to the rear for
example.
When it is put back in place, the seat
returns to its initial position. 5 - Head restraint height and
angle adjustment
To raise the head restraint, pull it up-
wards.
To lower it, it is necessary to push si-
multaneously:
- the button, located on the left guide at the base of the head re-
straint frame,
- the head restraint downwards.
No person or object should
prevent the seat from returning
t o i t s i n i t i a l p o s i t i o n ; t h e r e t u r n
to this position is necessary in
order for it to be secured. T h e h e a d r e s t r a i n t i s fi t t e d w i t h a f r a m e
which has notches which prevent it
f r o m l o w e r i n g ; t h i s i s a n i m p a c t s a f e t y
device.
Never drive with the head re-
s t r a i n t s r e m o v e d ; t h e y m u s t
be in place and correctly
adjusted.
The adjustment is correct
when the upper edge of
the head restraint is level
with the top of the head.
To adjust the angle of the head restraint,
tilt it.
To remove it, press the lug and pull
it upwards.
Page 50 of 194
3
53
6 - Heated seats control
Press the switch. The temperature is
controlled automatically.
Pressing the switch again switches
the function off. 7 - Storage drawer
Your vehicle has a storage drawer
under each seat.
To open it, lift it and pull.
To remove it, bring it to the end of its
travel, press the ends of the slides
and lift it, then pull it fully.
To put it back in place, at the end
of its travel, press on the top of the
drawer to secure it.
Do not place objects weighing
more than 1 kg in the drawers.
8 - Placing the passenger seat in
the table position
Use one of the two red controls located
at the base, on each side of the seat.
To place the seat in the table position,
lift this control with one hand and guide
the seat back to the table position with
the other hand.
To return the seat to the upright posi-
tion, carry out exactly the same pro-
cedure in reverse (always lift the red
control).
As a safety precaution, a
passenger sitting in the rear
of the vehicle must not place
his feet on the front seat
when placed in the table
position.
Page 52 of 194
3
55
Never drive with the head re-
straints removed, they must
be in place and correctly
adjusted.
Locked Released
In order to ensure that the
seat covers have a long ser-
vice life, do not leave the seat
in the table or "fully folded"
position after loading.
Avoid placing luggage on the seats
when they are in the table position.
REAR HEAD RESTRAINTS
The rear head restraints can be re-
m o v e d a n d h a v e t w o p o s i t i o n s ;
- high, position for use
- low, storage position
Repositioning the seat
Press the control D upwards to check
that the rear feet are released.
Tilt the folded seat rearwards.
The rear feet are secured automati-
cally.
Check that the seat is secured correctly.
R a i s e t h e s e a t b a c k , r e l e a s i n g i t fi r s t
by pulling the control C . To raise a head restraint, pull it up-
wards.
To lower it, press the lug then the
head restraint.
To remove it, place it in the high posi-
tion, push the lug and pull it upwards.
T o r e fi t i t , e n g a g e t h e h e a d r e s t r a i n t
rods in the holes taking care to remain
in the centreline of the seat back.
Page 64 of 194
3
67
4 - Seat cushion trims Fitting
Position the new trim on the seat
cushion or on the seat back.
Engage the zip pull, located at
the base of the seat cushion or
seat back.
Guide the zip pull along the three
sides of the seat cushion or seat
back.
Position the velcro on the last
side of the seat cushion or seat
back trim.
On the rear seats, take care to
position the velcro correctly so
that the ISOFIX mountings are not
covered.
Fold down the zip pull tab in
the seat cushion or seat back
location.
6 - Rear side storage
compartment cover trims
Removal
Remove the tab from the zip pull,
located at the base of the seat
cushion or seat back.
Guide the zip pull along the three
sides of the seat cushion or seat
back.
Remove the zip pull.
Pull on the last side to detach the
velcro, then remove the old seat
cushion or seat back trim.
Removal
Open the cover to 45°.
Unclip the lug located under the
cover.
Remove the old cover trim.
R e fi t t i n g
Open the cover to 45°.
Position the new trim on the cover
by means of the two notches.
Tilt the trim on the cover.
Clip the lug located under the
cover.
Some Cameleo seat trims
can be dry cleaned. Please
ask a PEUGEOT dealer for
details.
5 - Seat back trims
Follow these instructions starting, for
each seat, with the complete seat
c u s h i o n r e m o v a l a n d fi t t i n g o p e r a t i o n s ,
then repeat them for the seat back.
Page 68 of 194
3
71
REAR INTERIOR LAYOUT
5. Retaining straps
These secure the warning triangle,
the tool kit, oil cans...
1. Rear parcel shelf
To remove the shelf:
- tilt and slightly raise the shelf,
- pull upwards on each side to de-
tach it from its fasteners.
There are several options for storing
the shelf:
- either behind the rear seats,
- o r fl a t i n t h e b o o t .
2. Retaining hooks
3. Stowing rings
4. Luggage retaining net
Hooked onto the stowing rings, this
enables your luggage to be secured. 6 . S t o r a g e t r a y s i n t h e fl o o r
The right storage tray houses the
s u b w o o f e r o f t h e J B L a u d i o s y s t e m .
7. Armrests/Side storage trays
These have recesses for storing a
can and a bottle.
8. Grab handles with coat hook
