2008 PEUGEOT 1007 DAG engine
[x] Cancel search: enginePage 87 of 194
5
87
Front fog lamps and rear
fog lamp (2nd rotation of
the ring forwards).
Note : to switch off the
rear fog lamp and the front fog
lamps, turn the ring backwards twice
in succession.
Notes:
When the main beam headlamps are
switched on, the front fog lamps are
switched off.
When the lights are switched off au-
tomatically, with the engine running,
the front fog lamps and the side lights
will remain on (turn the ring back-
wards to switch the fog lamps off).
D i r e c t i o n i n d i c a t o r s ( fl a s h e r s )
Left
: downwards.
Right
: upwards.
When the lights are switched
off automatically or when
the dipped headlamps are
switched off manually, with
the engine running, the fog
lamps and the side lights
will remain on.
In good or rainy weather, both day
and night, the front fog lamps and
the rear fog lamp are dazzling and
are prohibited.
Do not forget to switch them off when
they are no longer needed. F o l l o w m e h o m e l i g h t i n g
Leaving the dipped headlamps on
temporarily, after switching off the
ignition, facilitates the driver's exit
from the vehicle when the light is
poor.
S w i t c h i n g o n
W i t h t h e i g n i t i o n o f f , " fl a s h " t h e
headlamps.
A s e c o n d " h e a d l a m p fl a s h "
switches the function off.
S w i t c h i n g o f f
The follow me home lighting is
switched off automatically following
l o c k i n g o f t h e d o o r s , a f t e r a s p e c i fi e d
time.
Page 94 of 194
5
91
COURTESY LIGHT
1. Front courtesy light
2. Map reading lights In the permanently on posi-
tion, there are different dura-
tions of lighting:
Boot light
The boot light is located in the left
boot trim.
It comes on automatically when the
boot is opened and switches of auto-
matically when the boot is closed.
Front courtesy light Permanently off.
Permanently on.
In this position, the courtesy
light comes on gradually:
- when the vehicle is unlocked,
- when the key is removed from the ignition,
- when the remote control locking button is pressed, in order to
locate your vehicle.
It switches off gradually:
- when the vehicle is locked,
- when the ignition is switched on,
- 30 seconds after the last door is closed. Map reading lights
With the ignition on, press
the corresponding switch 2 .
- when the ignition is off, approxi-
mately ten minutes,
- in energy economy mode, ap- proximately thirty seconds,
- when the engine is running, no limit.
Page 99 of 194
6
95
If this warning light comes on
on the instrument panel and
the indicator light on the but-
ton comes on, this indicates
that the ASR and ESP sys-
tems are disarmed.
TRACTION CONTROL (ASR) AND DYNAMIC STABILITY CONTROL (ESP)
Operation of the ASR and ESP
systems T h e w a r n i n g l i g h t fl a s h e s i f
t h e A S R o r E S P i s a c t i v a t e d . Disarming
I n e x c e p t i o n a l c o n d i t i o n s ( s t a r t i n g a
v e h i c l e w h i c h i s b o g g e d d o w n , s t u c k
in snow, on soft ground, ...), it may
b e a d v i s a b l e t o d i s a r m t h e A S R a n d
ESP systems, so that the wheels can
m o v e f r e e l y a n d r e g a i n g r i p .
Press the "ESP OFF" button,
located in the centre of the
fascia.
Reactivation T h e s e s y s t e m s a r e r e a c t i v a t e d a u t o -
matically each time the ignition is
switched back on or from 30 mph
(50 km/h).
Press the "ESP OFF" button again
t o r e a c t i v a t e t h e m m a n u a l l y .
Operating fault
If this warning light comes on,
accompanied by an audible
signal and a message on the
multifunction display, this indi-
cates a malfunction of these
systems.
H a v e t h e s y s t e m s c h e c k e d b y a
PEUGEOT dealer.
T h e E S P / A S R s y s t e m s o f f e r e x c e p -
t i o n a l s a f e t y i n n o r m a l d r i v i n g , b u t
t h i s s h o u l d n o t e n c o u r a g e t h e d r i v e r
t o t a k e e x t r a r i s k s o r d r i v e a t h i g h
speed.
The correct functioning of these
s y s t e m s d e p e n d s o n o b s e r v a t i o n o f
the manufacturer's recommenda-
tions regarding the wheels (tyres
and rims), the braking components,
the electronic components and the
PEUGEOT assembly and operation
procedures.
A f t e r a n i m p a c t , h a v e t h e s e s y s t e m s
checked by a PEUGEOT dealer.
Activation of the ASR and ESP
systems
When the ignition is on, the ASR and
E S P s y s t e m s a r e a l w a y s a c t i v e .
These systems are linked and com-
plement the ABS.
T h e A S R s y s t e m o p t i m i s e s d r i v e t o
p r e v e n t t h e w h e e l s s k i d d i n g , b y a c t -
i n g o n t h e b r a k e s o f t h e d r i v e w h e e l s
and on the engine. It also allows the
d i r e c t i o n a l s t a b i l i t y o f t h e v e h i c l e t o
b e i m p r o v e d o n a c c e l e r a t i o n .
I f t h e r e i s a v a r i a t i o n b e t w e e n t h e t r a -
j e c t o r y f o l l o w e d b y t h e v e h i c l e a n d
t h a t r e q u i r e d b y t h e d r i v e r , t h e E S P
system automatically acts on the
engine and the brake of one or more
w h e e l s , i n o r d e r t o p u t t h e v e h i c l e
back on course, within the limits of
the laws of physics.
Page 101 of 194
6
97
Seat belt not fastened warning I f t h e d r i v e r a n d / o r t h e
front passenger has not
fastened his seat belt,
the corresponding warn-
ing light comes on when
the ignition is on, then, at a speed
a b o v e 1 2 m p h ( 2 0 k m / h ) , t h i s i s a c c o m -
p a n i e d b y a n a u d i b l e s i g n a l t h e v o l u m e
o f w h i c h i n c r e a s e s ( f o r a p p r o x i m a t e l y
two minutes) and a message on the
multifunction display.
Note: a bag or an animal placed on
the front passenger seat may trigger
lighting of the warning light.
Seat belt unfastened warning
I f t h e d r i v e r a n d / o r o n e
of the passengers has
unfastened his seat
belt, the corresponding
warning light comes on
when the engine is running, then, at a
s p e e d a b o v e 1 2 m p h ( 2 0 k m / h ) , t h i s
is accompanied by an audible signal
t h e v o l u m e o f w h i c h i n c r e a s e s ( f o r
a p p r o x i m a t e l y t w o m i n u t e s ) a n d a
message on the multifunction display.
Rear seat belts
T h e r e a r s e a t s a r e fi t t e d w i t h t w o
three-point inertia reel seat belts.
The retaining of the rear seat belt
buckle by the sliding block makes
folding down or complete folding of
the seats easier.
Fastening
Pull the strap, then insert the
buckle in the stalk.
Check that the seat belt is
fastened correctly by pulling the
strap.
Unfastening
Press the red button on the stalk.
Version with colour display
I f t h e d r i v e r a n d / o r o n e o f t h e p a s -
sengers has not fastened (or has
unfastened) his seat belt, a message
appears on the multifunction display.
Page 110 of 194
7
103
Functions of the steering
wheel controls
+
:
manual gear changing in sequential
mode.
Press behind the "+" steering wheel
control to change up.
-
:
manual gear changing in sequential
mode.
Press behind the "-" steering wheel
control to change down. Stopping - Starting on a slope
The "2 Tronic" gearbox is a controlled
manual gearbox which does not have
a clutch pedal.
Do not use the accelerator pedal to
immobilise the vehicle on a slope,
apply the handbrake instead.
When starting on a slope, accelerate
gradually while releasing the hand-
brake.
Moving off
Select position N . Switching to sequential mode
Once you have moved off, you can
switch to sequential mode by select-
ing position
M .
"AUTO" disappears and the gears
engaged appear in succession on
the instrument panel display.
The gear change requests are only
carried out if the engine speed
permits it.
Take your foot off the accelerator
pedal gently to engage the gear.
At low speeds, when approaching a
s t o p o r t r a f fi c l i g h t s f o r e x a m p l e , t h e
g e a r b o x c h a n g e s d o w n t o fi r s t g e a r
automatically.
P r e s s t h e b r a k e p e d a l fi r m l y
while starting the engine.
Start the engine. "N" appears on the
instrument panel display.
S e l e c t fi r s t g e a r ( p o s i t i o n M or A ) or
r e v e r s e ( p o s i t i o n R ).
Release the handbrake.
Release the brake pedal then acce-
lerate.
"AUTO" and "1" or "R" appear on
the instrument panel display.
It is possible to start in 2nd gear
using the gear lever, in sequential
mode only.
Page 111 of 194
7
104
Switching to automated mode Reinitialisation
Following disconnection of the battery,
the gearbox must be reinitialised: The brake pedal must be
pressed while starting the
engine.
Never select neutral N while the vehi-
cle is moving.
Only engage reverse gear R with the
vehicle immobilised and the brake
pedal pressed.
In all cases, it is imperative that
you apply the handbrake in order to
immobilise the vehicle.
On a steep gradient, it is preferable
to switch to sequential mode.
"Auto sequential" mode
In the automated mode, you can
resume control temporarily at any
time using the steering wheel controls.
The use of these controls permits
manual selection of the gears in situ-
ations which require a faster change-
down than that offered in automated
m o d e ( a r r i v a l a t a r o u n d a b o u t , e x i t
from a car park with a steep gradient,
overtaking...).
The gearbox engages the gear re-
quested if the engine speed permits
it.
"AUTO" is still displayed on the
instrument panel.
After a few moments, the gearbox
again controls the gears automatically.
Stopping the vehicle
Before switching off the engine, you
can:
- move to position N to leave the
gearbox in neutral.
- leave a gear engaged, such as fi r s t o r r e v e r s e .
In both cases, it is imperative that
you apply the handbrake to immobi-
lise the vehicle. Operating anomaly
W i t h t h e i g n i t i o n o n , t h e fl a s h i n g o f
"AUTO" and lighting of the service
warning light, accompanied by an
audible signal and a message on the
multifunction display, indicate a gear-
box malfunction.
Contact a PEUGEOT dealer without
delay.
If you press the accelerator
pedal beyond the point of
resistance, the gearbox
selects the gear below to
permit sharper acceleration. - switch on the ignition,
"AUTO"
and "-" appear on the instrument
panel display,
- press the brake pedal,
- wait approximately 30 seconds until "N" or a gear appears on
the instrument panel display,
- release the brake pedal.
The gearbox is operational again.
Automated mode
After using the sequential mode, you
can return to the automated mode by
selecting position
A .
"AUTO" and the gear engaged appear
on the instrument panel display.
The gearbox then operates in auto-
active mode, without any action on
the part of the driver.
It continuously selects the gear most
suited to the following parameters:
- driving style,
- road characteristics,
- vehicle load.
To optimise driving comfort and
obtain the most suitable gear, avoid
sharp variations in the pressure on
the accelerator pedal.
Page 117 of 194
7
110
If there is an operating fault,
when reverse gear is enga-
ged, the service warning
light comes on, accompa-
nied by an audible signal
( s h o r t b l e e p ) a n d a m e s s a g e
on the multifunction display.
In bad or wintry weather, ensure that
the sensors are not covered with
mud, frost or snow.
Deactivation
With the engine running, press button A
to deactivate the system permanently.
The indicator light on the button comes
on.
The system will be deactivated
automatically when towing a trailer or
w h e n a b i c y c l e c a r r i e r i s fi t t e d ( v e h i c l e
fi t t e d w i t h a t o w b a r o r b i c y c l e c a r r i e r
recommended by PEUGEOT ).
Reactivation
Press button A again to reactivate
the system. The indicator light on the
button is switched off.
Page 118 of 194
8
112
From outside: lift the catch A and
raise the bonnet. Bonnet strut
Secure the strut to hold the bonnet
open.
Before closing the bonnet, replace
the strut in its housing.
To close
Lower the bonnet and release it at
the end of its travel. Check that the
bonnet is properly locked.
OPENING THE BONNET
From inside: pull the handle on the
left-hand side under the fascia.
RUNNING OUT OF FUEL (DIESEL)
I f y o u r v e h i c l e i s fi t t e d w i t h a n H D I
engine, the fuel circuit must be rep-
rimed if you run out of fuel (refer to
the corresponding graphic).
This system consists of a repriming
pump and a transparent pipe.
1.4 litre Turbo HDI engine
Open the bonnet.
F i l l t h e f u e l t a n k w i t h a t l e a s t fi v e
litres of diesel.
Squeeze and release the rep-
riming pump until fuel appears in
the transparent pipe.
Operate the starter until the en-
gine starts.
Close the bonnet.
1.6 litre Turbo HDI 16V engine
Open the bonnet.
Fill the fuel tank with at least
fi v e l i t r e s o f d i e s e l .
Unclip the style cover to gain
access to the repriming pump.
Squeeze and release the rep-
riming pump until fuel appears
in the transparent pipe with the
green connector.
Operate the starter until the
engine starts.
Put the style cover back in posi-
tion and clip it in place.
Close the bonnet.
Opening the bonnet may
cause serious injuries,
please observe the following
recommendations:
- protect your hands and clothing,
- always allow the engine to cool before opening the bonnet,
- place the strut in its housing on the wing correctly,
- c h e c k t h a t t h e b o n n e t i s fi r m l y secured in the open position,
- be aware of gusts of wind as they could cause the bonnet to
close suddenly.