2008 PEUGEOT 1007 DAG boot

9
117
Parking the vehicle
- If possible, park the vehicle on level, stable and non-slippery
ground.
- It is imperative that you ensure that the occupants get out of the vehi-
cle and wait in a safe location.
- Apply the handbrake, switch off the ignition and engage fi rst or
reverse gear (position R for the
"2 Tronic" gearbox).
CHANGING A WHEEL

1. Jack with integrated handle.

2. Chock.

3. Wheelbrace.

4. Extension.

5. "Bolt cover" tool.

6. Removable towing eye. Access to the spare wheel and
the jack
The wheel is located outside the ve-
hicle, under the rear fl oor, supported
by a metal carrier.
- Unclip the cover to gain access
to the spare wheel carrier retain-
ing bolt, located on the inside
near the closing system.
- Using the wheelbrace 3 and the
extension 4 , slacken the spare
wheel carrier retaining bolt.
- Lift the carrier to release the hook rearwards, then lower it.
- Remove the spare wheel and the box.
- Remove the jack 1 from the box.
Tools provided
The jack is stored in a box in the cen-
tre of the spare wheel. The chock is
fi xed on the side of the box.
The other tools are stored in a case
in the left boot trim.
Note: if your vehicle is fi tted with a
towbar, the case is stored in the left
storage tray (located in the fl oor of
the rear footwell).

9
118
Removing a wheel
- Place the chock 2 (integrated
with the box) at the rear of the
wheel diagonally opposite the
wheel to be changed.
- Remove the wheel trim, using the wheelbrace 3 , by pulling at
the valve passage hole.
- Remove the chrome-plated bolt covers and the plastic cover from
the bolts using the "bolt cover" tool 5
(Special features of alloy wheels).
- Slacken the wheel bolts.
- Place the jack 1 under one of the
four locating points A on the sub-
frame closest to the wheel to be
changed. Ensure that the entire
surface of the jack base plate is
in contact with the ground.
-
Extend the jack, completely unscrew
the bolts and remove the wheel.
Refitting the wheel
- Position the wheel on the hub.
- Lightly pre-tighten the bolts us- ing the wheelbrace 3 .
-
Compress the jack 1 and release it.
- Fully tighten the bolts using the wheelbrace.
- Replace the trim, starting at the valve passage hole, and press it
on using the palm of the hand.
For your safety, always
change a wheel:
- Stow the tools in the case, then
put it back in the left boot trim.
The jack and the tool kit are specifi c
to your vehicle. Do not use them for
other purposes.
Replacing the wheel in the
carrier
- Replace the jack 1 in the box.
- Replace the box in the wheel.
- Replace the wheel in the carrier.
- Lift the wheel then the carrier and reposition the hook.
- Do not forget to fully tighten the spare wheel carrier retaining bolt. After changing the wheel
- Have the tightening of the bolts
and the pressure of the spare
tyre checked as soon as possi-
ble by a PEUGEOT dealer.
- Do not exceed its maximum au- thorised speed: 50 mph (80 km/h).
- Have the punctured tyre repaired and replace it on the vehicle as
soon as possible.
- 15 and 16 inch punctured wheels cannot be placed in the carrier.
- on level, stable and non-slippery
ground,
- with the handbrake applied,
- with fi rst or reverse gear engaged (position R for the "2 Tronic" gear-
box),
- with the vehicle chocked,
- never go underneath a vehicle raised using a jack (use an axle
stand).

9
122
Rear lights

1. Brake/side lights
(P21 W/5 W).

2. Direction indicators (P21 W).

3. Reversing light (P21 W), right
side.
Fog lamp (P21 W), left side.
These 4 bulbs are changed by re-
moving the light:

 Remove the access fl ap in the
corresponding boot side trim to
access the light,

 Remove the two light fi xing nuts
inside the boot,

 Unclip the harness,

 Remove the light pressing on the
retaining tabs,

 Remove the seal,
 Remove the bulb holder moving
aside the two tabs A ,

 Turn the bulb a quarter of a turn,

 Remove the bulb and change it.

Note: if necessary, use the wheel-
brace to remove the nuts.
When refi tting, proceed in the re-
verse order and take care to position
the bulb holder, the seal and the light
correctly. Third brake light
(4 W 5 W bulbs)

 Using a 10 mm box spanner, un-
screw the 2 fi xing nuts A .

 Release the lamp unit by push-
ing it outwards.

 Disconnect the connector and
the rear wash-wipe pipe.

 Turn the bulb holder a quarter of
a turn and remove it.

 Remove the bulb and change it.
When refi tting, proceed in the re-
verse order and ensure that the lamp
unit seal and the rear wash-wipe pipe
have been put back in place correctly.
Do not tighten the nuts more than is
necessary at the risk of breaking the
light.
Number plate lights (W 5 W)

 Insert a thin screwdriver into one
of the external holes of the lens.

 Push it outwards to unclip it.

 Remove the lens.

 Remove the bulb and change it.

9
129
TOWING YOUR VEHICLE
From the rear:

 Unclip the side of the cover using
the fl at part of the towing eye,

 Screw in the towing eye until it
locks. When towing with the en-
gine switched off, there is no
braking assistance.
Special features of
the "2 Tronic" gearbox
When towing with four wheels on the
ground, the following rules must be
obeyed:
- gear lever in position
N ,
- tow the vehicle at less than 30 mph (50 km/h) over a maxi-
mum distance of 30 miles (50 km).
- do not add oil to the gearbox.
From the front:

 Unclip the bottom of the cover,
using the fl at part of the towing
eye.

 Screw in the towing eye until it
locks. Lifting
(2 wheels only on the road)
It is preferable to raise the vehicle by
the wheels.

Never use the radiator crossmember.
Without lifting
(4 wheels on the road)
You should always use a towbar.
The removable towing eye is stored
in the tool case, located in the left
boot trim.
Vehicles fitted with a manual
gearbox (diesel version)
In the case of vehicles fi tted with a
manual gearbox, the gear lever must
be in the neutral position.
Failure to observe this special condi-
tion may result in damage to certain
braking components and the absence
of braking assistance the next time
the engine is started.

9
131
ACCESSORIES FOR YOUR 1007
A wide range of accessories recom-
mended by PEUGEOT and original
parts are offered by the Network.
They all benefi t from PEUGEOT's
recommendation.
These accessories and parts, having
been tested and approved for reli-
ability and safety, are all adapted to
your PEUGEOT vehicle. The fi tting of electrical equip-
ment or accessories which
are not recommended by
PEUGEOT may result in a
failure of your vehicle's electronic
system.
Please note this specifi c warning.
You are advised to contact a repre-
sentative of the Marque to be shown
the range of recommended equip-
ment and accessories.
Depending on the country in which
the vehicle is sold, it is compulsory to
have a safety jacket, warning trian-
gle and spare bulbs available in the
vehicle.

"Protection": anti-theft
alarm , engraved windows,
wheel anti-theft devices,
system which assists with
the identifi cation of a stolen
vehicle, fi rst aid kit, warn-
ing triangle, high visibility
safety jacket, fog lamps kit,
snow chains, non-skid cov-
ers, audible rear parking
assistance.

"Touring": central arm-
rest, storage under the rear
shelf, mats * , boot tray, sun
blinds.
For leisure pursuits: roof
bars, transportation ac-
cessories (bicycle carrier,
ski carrier), roof box, child
seats and booster cushions, audio/
telephone console, cool box.

"In-Car Technology": hands-
free kits, satellite navigation
systems, CD changer, DVD
player, multimedia, audio
equipment, speakers, auxil-
iary audio socket permitting
the connection of a portable
MP3 player (compatible with
WIP Sound), USB socket.

"Styling": seat covers, al-
loy wheels, wheel trims,
spoiler, styling strips, door
spoilers, sill protectors,
aluminium footrest, rear si-
lencer, exhaust tail pipe.

"Universal": windscreen
wash fl uid, interior and ex-
terior cleaning and mainte-
nance products.
You can obtain "Van" conver-
sion kits for conversion from
a private vehicle to a van.
You can obtain other
"Cameleo" customising kits
from PEUGEOT dealers.
You will be offered either a
complete kit, like the original kit, or a
partial kit consisting of the vent trims
only.
Should you need to change one or
more elements of the Cameleo kit of
your vehicle, due to damage..., you
will be offered replacement elements
from the exchange kits available at
that time.
This product range offered by PEUGEOT
Accessories is structured around 5 catego-
ries: PROTECTION - TOURING - IN-CAR
TECHNOLOGY - STYLING - UNIVERSAL.
* To prevent jamming under the
pedals:
- ensure that the mat is positioned and secured correctly,
- never fi t one mat on top of an- other.
Trailer towbar which must be fi tted by
the PEUGEOT network.