2008 NISSAN TEANA check engine

DLK-82
< COMPONENT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
INTELLIGENT KEY WARNING BUZZER
INTELLIGENT KEY WARNING BUZZER
DescriptionINFOID:0000000003794889
Answers back and warns for an inappropriate operation.
Component Function CheckINFOID:0000000003794890
1.CHECK FUNCTION
Check Intelligent Key warning buzzer (“OUTSIDE BUZZER”) in Active Test mode.
Is the inspection result normal?
YES >> Intelligent Key warning buzzer (engine room) is OK.
NO >> Refer to DLK-82, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000003794891
1.CHECK FUSE
1. Turn ignition switch OFF.
2. Check 10 A fuse, [No.6, located in fuse block (J/B)].
Is fuse fusing?
YES >> Replace the blown fuse after repairing the affected circuit if a fuse is blown.
NO >> GO TO 2.
2.CHECK INTELLIGENT KEY WARNING BUZZER POWER SUPPLY CIRCUIT
1. Disconnect Intelligent Key warning buzzer connector.
2. Check voltage between Intelligent Key warning buzzer harness connector and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace Intelligent Key warning buzzer power supply circuit.
3.CHECK INTELLIGENT KEY WARNING BUZZER CIRCUIT
1. Disconnect BCM connector.
2. Check continuity between BCM harness connector and Intelligent Key warning buzzer harness connector.
3. Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair or replace harness.
4.CHECK INTELLIGENT KEY WARNING BUZZER
Check DLK-83, "
Component Inspection".
Is the inspection result normal?
(+)
(–)Voltage (V)
(Approx.) Intelligent Key warning buzzer
Connector Terminal
E25 1 Ground Battery voltage
BCM Intelligent Key warning buzzer
Continuity
Connector Terminal Connector Terminal
M121 64 E25 3 Existed
BCM
GroundContinuity
Connector Terminal
M121 64 Not existed

DLK-84
< COMPONENT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
INTELLIGENT KEY
INTELLIGENT KEY
DescriptionINFOID:0000000003794893
The following functions are available when having and carrying electronic ID.
 Door lock/unlock
 Trunk lid open
 Engine start
Remote control entry function and panic alarm function have specific buttons.
Component Function CheckINFOID:0000000003794894
1.CHECK FUNCTION
Check remote keyless entry receiver (“RKE OPE COUN1”) in Data Monitor mode with CONSULT-III.
Is the inspection result normal?
YES >> Intelligent Key is OK.
NO >> Refer to DLK-84, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000003794895
1.CHECK INTELLIGENT KEY BATTERY
Check by connecting a resistance (approximately 300 Ω) so that the
current value becomes about 10 mA.
Is the measurement value within the specification?
YES >> Replace Intelligent Key.
NO >> Replace Intelligent Key battery. Refer to DLK-84, "
Com-
ponent Inspection".
Component InspectionINFOID:0000000003794896
1. REPLACE INTELLIGENT KEY BATTERY
1. Release the lock knob at the back of the Intelligent Key and remove the mechanical key.
2. Insert a flat-bladed screwdriver (A) wrapped with a cloth into the
slit of the corner and twist it to separate the upper part from the
lower part.
CAUTION:
 Never touch the circuit board or battery terminal.
 The key fob is water-resistant. However, if it does get wet,
immediately wipe it dry.
3. Replace the battery with new one.
Monitor item Condition
RKE OPE COUN1 Check that the numerical value is changing while operating on the Intelligent Key.
Standard : Approx. 2.5 - 3.0 V
OCC0607D
PIIB6221E

EC-2
Component Parts Location ...................................53
Component Description .........................................58
CAN COMMUNICATION ...................................59
System Description .................................................59
COOLING FAN CONTROL ...............................60
System Diagram .....................................................60
System Description .................................................60
Component Parts Location ...................................62
Component Description ..........................................67
ELECTRONIC CONTROLLED ENGINE
MOUNT ..............................................................
68
System Diagram .....................................................68
System Description .................................................69
Component Parts Location ...................................70
Component Description .........................................75
EVAPORATIVE EMISSION SYSTEM ...............76
System Diagram .....................................................76
System Description .................................................76
Component Parts Location ...................................80
Component Description .........................................85
INTAKE VALVE TIMING CONTROL .................86
System Diagram .....................................................86
System Description .................................................86
Component Parts Location ...................................87
Component Description ..........................................92
VARIABLE INDUCTION AIR SYSTEM .............93
System Diagram .....................................................93
System Description .................................................93
Component Parts Location ...................................96
Component Description ........................................101
ON BOARD DIAGNOSTIC (OBD) SYSTEM ...102
Diagnosis Description ............................................102
CONSULT-III Function ..........................................113
Diagnosis Tool Function ......................................122
COMPONENT DIAGNOSIS .......................124
TROUBLE DIAGNOSIS - SPECIFICATION
VALUE .............................................................
124
Description .............................................................124
Component Function Check ..................................124
Diagnosis Procedure .............................................125
POWER SUPPLY AND GROUND CIRCUIT ...132
Diagnosis Procedure .............................................132
U1000, U1001 CAN COMM CIRCUIT .............135
Description .............................................................135
DTC Logic ..............................................................135
Diagnosis Procedure .............................................135
P0011, P0021 IVT CONTROL .........................136
DTC Logic ..............................................................136
Diagnosis Procedure .............................................137
Component Inspection ..........................................138
P0031, P0032, P0051, P0052 A/F SENSOR 1
HEATER ...........................................................
140
Description ............................................................140
DTC Logic .............................................................140
Diagnosis Procedure .............................................140
Component Inspection ..........................................142
P0037, P0038, P0057, P0058 HO2S2 HEAT-
ER .....................................................................
143
Description ............................................................143
DTC Logic .............................................................143
Diagnosis Procedure .............................................144
Component Inspection ..........................................145
P0075, P0081 IVT CONTROL SOLENOID
VALVE ..............................................................
146
Description ............................................................146
DTC Logic .............................................................146
Diagnosis Procedure .............................................146
Component Inspection ..........................................147
P0102, P0103 MAF SENSOR ..........................149
Description ............................................................149
DTC Logic .............................................................149
Diagnosis Procedure .............................................150
Component Inspection ..........................................151
P0112, P0113 IAT SENSOR ............................154
Description ............................................................154
DTC Logic .............................................................154
Diagnosis Procedure .............................................155
Component Inspection ..........................................155
P0117, P0118 ECT SENSOR ...........................157
Description ............................................................157
DTC Logic .............................................................157
Diagnosis Procedure .............................................158
Component Inspection ..........................................158
P0122, P0123 TP SENSOR ..............................160
Description ............................................................160
DTC Logic .............................................................160
Diagnosis Procedure .............................................160
Component Inspection ..........................................162
Special Repair Requirement .................................162
P0130, P0150 A/F SENSOR 1 .........................163
Description ............................................................163
DTC Logic .............................................................163
Component Function Check .................................165
Diagnosis Procedure .............................................165
P0131, P0151 A/F SENSOR 1 .........................167
Description ............................................................167
DTC Logic .............................................................167
Diagnosis Procedure .............................................168
P0132, P0152 A/F SENSOR 1 .........................170
Description ............................................................170

EC-3
C
D
E
F
G
H
I
J
K
L
M
ECA
N
O
P DTC Logic .............................................................
170
Diagnosis Procedure .............................................171
P0133, P0153 A/F SENSOR 1 .........................173
Description ............................................................173
DTC Logic .............................................................173
Diagnosis Procedure .............................................175
P0137, P0157 HO2S2 ......................................178
Description ............................................................178
DTC Logic .............................................................178
Component Function Check ..................................179
Diagnosis Procedure .............................................180
Component Inspection ..........................................182
P0138, P0158 HO2S2 ......................................184
Description ............................................................184
DTC Logic .............................................................184
Component Function Check ..................................186
Diagnosis Procedure .............................................187
Component Inspection ..........................................190
P0139, P0159 HO2S2 ......................................192
Description ............................................................192
DTC Logic .............................................................192
Component Function Check ..................................193
Diagnosis Procedure .............................................194
Component Inspection ..........................................195
P0171, P0174 FUEL INJECTION SYSTEM
FUNCTION .......................................................
198
DTC Logic .............................................................198
Diagnosis Procedure .............................................199
P0172, P0175 FUEL INJECTION SYSTEM
FUNCTION .......................................................
202
DTC Logic .............................................................202
Diagnosis Procedure .............................................203
P0222, P0223 TP SENSOR .............................206
Description ............................................................206
DTC Logic .............................................................206
Diagnosis Procedure .............................................206
Component Inspection ..........................................207
Special Repair Requirement .................................208
P0300, P0301, P0302, P0303, P0304, P0305,
P0306 MISFIRE ................................................
209
DTC Logic .............................................................209
Diagnosis Procedure .............................................210
P0327, P0328, P0332, P0333 KS ....................215
Description ............................................................215
DTC Logic .............................................................215
Diagnosis Procedure .............................................215
Component Inspection ..........................................216
P0335 CKP SENSOR (POS) ............................218
Description ............................................................218
DTC Logic .............................................................218
Diagnosis Procedure .............................................219
Component Inspection ...........................................221
P0340, P0345 CMP SENSOR (PHASE) .........222
Description .............................................................222
DTC Logic ..............................................................222
Diagnosis Procedure .............................................223
Component Inspection ...........................................224
P0420, P0430 THREE WAY CATALYST
FUNCTION ......................................................
226
DTC Logic ..............................................................226
Component Function Check ..................................227
Diagnosis Procedure .............................................228
P0444 EVAP CANISTER PURGE VOLUME
CONTROL SOLENOID VALVE ......................
231
Description .............................................................231
DTC Logic ..............................................................231
Diagnosis Procedure .............................................231
Component Inspection ...........................................232
P0500 VSS ......................................................234
Description .............................................................234
DTC Logic ..............................................................234
Component Function Check ..................................235
Diagnosis Procedure .............................................235
P0550 PSP SENSOR ......................................236
Description .............................................................236
DTC Logic ..............................................................236
Diagnosis Procedure .............................................236
Component Inspection ...........................................237
P0603 ECM POWER SUPPLY .......................238
Description .............................................................238
DTC Logic ..............................................................238
Diagnosis Procedure .............................................238
P0605 ECM .....................................................240
Description .............................................................240
DTC Logic ..............................................................240
Diagnosis Procedure .............................................241
P0607 ECM .....................................................242
Description .............................................................242
DTC Logic ..............................................................242
Diagnosis Procedure .............................................242
P0643 SENSOR POWER SUPPLY ................243
DTC Logic ..............................................................243
Diagnosis Procedure .............................................243
P0850 PNP SWITCH .......................................245
Description .............................................................245
DTC Logic ..............................................................245
Component Function Check ..................................246
Diagnosis Procedure (VQ35DE engine) ................246
Diagnosis Procedure (VQ25DE engine) ................247
P1212 TCS COMMUNICATION LINE .............249
Description .............................................................249

EC-4
DTC Logic ..............................................................249
Diagnosis Procedure .............................................249
P1217 ENGINE OVER TEMPERATURE .........250
DTC Logic ..............................................................250
Component Function Check ..................................250
Diagnosis Procedure .............................................251
P1225 TP SENSOR .........................................254
Description .............................................................254
DTC Logic ..............................................................254
Diagnosis Procedure .............................................254
Special Repair Requirement ..................................255
P1226 TP SENSOR .........................................256
Description .............................................................256
DTC Logic ..............................................................256
Diagnosis Procedure .............................................256
Special Repair Requirement ..................................257
P1550 BATTERY CURRENT SENSOR ..........258
Description .............................................................258
DTC Logic ..............................................................258
Diagnosis Procedure .............................................258
Component Inspection ...........................................259
P1551, P1552 BATTERY CURRENT SEN-
SOR ..................................................................
261
Description .............................................................261
DTC Logic ..............................................................261
Diagnosis Procedure .............................................261
Component Inspection ...........................................262
P1553 BATTERY CURRENT SENSOR ..........264
Description .............................................................264
DTC Logic ..............................................................264
Diagnosis Procedure .............................................264
Component Inspection ...........................................265
P1554 BATTERY CURRENT SENSOR ..........267
Description .............................................................267
DTC Logic ..............................................................267
Component Function Check ..................................267
Diagnosis Procedure .............................................268
Component Inspection ...........................................269
P1564 ASCD STEERING SWITCH .................270
Description .............................................................270
DTC Logic ..............................................................270
Diagnosis Procedure .............................................270
Component Inspection ...........................................272
P1572 ASCD BRAKE SWITCH .......................273
Description .............................................................273
DTC Logic ..............................................................273
Diagnosis Procedure .............................................274
Component Inspection (ASCD Brake Switch) .......277
Component Inspection (Stop Lamp Switch) ..........277
P1574 ASCD VEHICLE SPEED SENSOR ......278
Description .............................................................278
DTC Logic .............................................................278
Diagnosis Procedure .............................................278
P1700 CVT CONTROL SYSTEM .....................280
Description ............................................................280
P1715 INPUT SPEED SENSOR (PRIMARY
SPEED SENSOR) .............................................
281
Description ............................................................281
DTC Logic .............................................................281
Diagnosis Procedure .............................................281
P1720 VSS ........................................................283
Description ............................................................283
DTC Logic .............................................................283
Diagnosis Procedure .............................................283
P1800 VIAS CONTROL SOLENOID VALVE 1 ..285
Description ............................................................285
DTC Logic .............................................................285
Diagnosis Procedure .............................................285
Component Inspection ..........................................286
P1801 VIAS CONTROL SOLENOID VALVE 2 ..288
Description ............................................................288
DTC Logic .............................................................288
Diagnosis Procedure .............................................288
Component Inspection ..........................................289
P1805 BRAKE SWITCH ...................................291
Description ............................................................291
DTC Logic .............................................................291
Diagnosis Procedure .............................................291
Component Inspection (Stop Lamp Switch) ..........292
P2100, P2103 THROTTLE CONTROL MO-
TOR RELAY .....................................................
294
Description ............................................................294
DTC Logic .............................................................294
Diagnosis Procedure .............................................294
P2101 ELECTRIC THROTTLE CONTROL
FUNCTION ........................................................
296
Description ............................................................296
DTC Logic .............................................................296
Diagnosis Procedure .............................................296
Component Inspection ..........................................298
Special Repair Requirement .................................299
P2118 THROTTLE CONTROL MOTOR ..........300
Description ............................................................300
DTC Logic .............................................................300
Component Inspection ..........................................300
Special Repair Requirement .................................300
P2119 ELECTRIC THROTTLE CONTROL
ACTUATOR ......................................................
302
Description ............................................................302
DTC Logic .............................................................302
Diagnosis Procedure .............................................303
Special Repair Requirement .................................303

EC-5
C
D
E
F
G
H
I
J
K
L
M
ECA
N
O
P
P2122, P2123 APP SENSOR ...........................304
Description ............................................................304
DTC Logic .............................................................304
Diagnosis Procedure .............................................304
Component Inspection ..........................................306
Special Repair Requirement .................................306
P2127, P2128 APP SENSOR ...........................307
Description ............................................................307
DTC Logic .............................................................307
Diagnosis Procedure .............................................307
Component Inspection ..........................................309
Special Repair Requirement .................................310
P2135 TP SENSOR ..........................................311
Description ............................................................311
DTC Logic .............................................................311
Diagnosis Procedure .............................................311
Component Inspection ..........................................313
Special Repair Requirement .................................313
P2138 APP SENSOR .......................................314
Description ............................................................314
DTC Logic .............................................................314
Diagnosis Procedure .............................................314
Component Inspection ..........................................316
Special Repair Requirement .................................317
P2A00, P2A03 A/F SENSOR 1 ........................318
Description ............................................................318
DTC Logic .............................................................318
Diagnosis Procedure .............................................319
ASCD BRAKE SWITCH ...................................321
Description ............................................................321
Component Function Check ..................................321
Diagnosis Procedure .............................................321
Component Inspection (ASCD Brake Switch) .......322
ASCD INDICATOR ...........................................323
Description ............................................................323
Component Function Check ..................................323
Diagnosis Procedure .............................................323
COOLING FAN .................................................324
Description ............................................................324
Component Function Check ..................................324
Diagnosis Procedure .............................................324
Component Inspection (Cooling Fan Motor) .........327
Component Inspection (Cooling Fan Relay) .........328
ELECTRICAL LOAD SIGNAL .........................329
Description ............................................................329
Component Function Check ..................................329
Diagnosis Procedure .............................................329
ELECTRONIC CONTROLLED ENGINE
MOUNT .............................................................
331
Description ............................................................331
Component Function Check ..................................331
Diagnosis Procedure .............................................331
Component Inspection ...........................................332
FUEL INJECTOR ............................................334
Description .............................................................334
Component Function Check ..................................334
Diagnosis Procedure .............................................334
Component Inspection ...........................................336
FUEL PUMP ....................................................337
Description .............................................................337
Component Function Check ..................................337
Diagnosis Procedure .............................................337
Component Inspection (Fuel Pump) ......................340
Component Inspection (Condenser) ......................340
IGNITION SIGNAL ..........................................341
Description .............................................................341
Component Function Check ..................................341
Diagnosis Procedure .............................................341
Component Inspection (Ignition Coil with Power
Transistor) .............................................................
344
Component Inspection (Condenser) ......................345
MALFUNCTION INDICATOR .........................346
Description .............................................................346
Component Function Check ..................................346
Diagnosis Procedure .............................................346
POSITIVE CRANKCASE VENTILATION .......347
Description .............................................................347
Component Inspection ...........................................347
REFRIGERANT PRESSURE SENSOR ..........348
Description .............................................................348
Component Function Check ..................................348
Diagnosis Procedure .............................................348
VARIABLE INDUCTION AIR SYSTEM ..........351
Description .............................................................351
Component Function Check (VQ35DE engine) .....351
Component Function Check (VQ25DE engine) .....353
Diagnosis Procedure (VQ35DE engine) ................353
Diagnosis Procedure (VQ25DE engine) ................355
ECU DIAGNOSIS .......................................357
ECM .................................................................357
Reference Value ....................................................357
Wiring Diagram—ENGINE CONTROL SYS-
TEM— ...................................................................
371
Fail safe .................................................................386
DTC Inspection Priority Chart .............................388
DTC Index .............................................................389
How to Set SRT Code ........................................392
Test Value and Test Limit ...................................394
SYMPTOM DIAGNOSIS ............................400
ENGINE CONTROL SYSTEM SYMPTOMS ...400
Symptom Table .....................................................400
NORMAL OPERATING CONDITION .............404

INSPECTION AND ADJUSTMENT
EC-11
< BASIC INSPECTION >[VQ25DE, VQ35DE]
C
D
E
F
G
H
I
J
K
L
MA
EC
N
P O
INSPECTION AND ADJUSTMENT
BASIC INSPECTION
BASIC INSPECTION : Special Repair RequirementINFOID:0000000003856444
1.INSPECTION START
1. Check service records for any recent repairs that may indicate a related malfunction, or a current need for
scheduled maintenance.
2. Open engine hood and check the following:
- Harness connectors for improper connections
- Wiring harness for improper connections, pinches and cut
- Vacuum hoses for splits, kinks and improper connections
- Hoses and ducts for leaks
- Air cleaner clogging
- Gasket
3. Confirm that electrical or mechanical loads are not applied.
- Head lamp switch is OFF.
- Air conditioner switch is OFF.
- Rear window defogger switch is OFF.
- Steering wheel is in the straight-ahead position, etc.
4. Start engine and warm it up until engine coolant temperature
indicator points the middle of gauge.
Ensure engine stays below 1,000 rpm.
5. Run engine at about 2,000 rpm for about 2 minutes under no
load.
6. Check that no DTC is displayed with CONSULT-III or GST.
Are any DTCs detected?
YES >> GO TO 2.
NO >> GO TO 3.
2.REPAIR OR REPLACE
Repair or replace components as necessary according to corresponding Diagnostic Procedure.
>> GO TO 3
3.CHECK TARGET IDLE SPEED
1. Run engine at about 2,000 rpm for about 2 minutes under no load.
SEF983U
SEF976U
SEF977U

EC-12
< BASIC INSPECTION >[VQ25DE, VQ35DE]
INSPECTION AND ADJUSTMENT
2. Rev engine between 2,000 and 3,000 rpm 2 or 3 times under no
load, then run engine at idle speed for about 1 minute.
3. Check idle speed.
For procedure, refer to EC-14, "
IDLE SPEED : Special Repair
Requirement".
For specification, refer to EC-414, "
Idle Speed".
Is the inspection result normal?
YES >> GO TO 10.
NO >> GO TO 4.
4.PERFORM ACCELERATOR PEDAL RELEASED POSITION LEARNING
1. Stop engine.
2. Perform EC-15, "
ACCELERATOR PEDAL RELEASED POSITION LEARNING : Special Repair Require-
ment".
>> GO TO 5.
5.PERFORM THROTTLE VALVE CLOSED POSITION LEARNING
Perform EC-16, "
THROTTLE VALVE CLOSED POSITION LEARNING : Special Repair Requirement".
>> GO TO 6.
6.PERFORM IDLE AIR VOLUME LEARNING
Perform EC-16, "
IDLE AIR VOLUME LEARNING : Special Repair Requirement".
Is Idle Air Volume Learning carried out successfully?
YES >> GO TO 7.
NO >> Follow the instruction of Idle Air Volume Learning. Then GO TO 4.
7.CHECK TARGET IDLE SPEED AGAIN
1. Start engine and warm it up to normal operating temperature.
2. Check idle speed.
For procedure, refer to EC-14, "
IDLE SPEED : Special Repair Requirement".
For specification, refer to EC-414, "
Idle Speed".
Is the inspection result normal?
YES >> GO TO 10.
NO >> GO TO 8.
8.DETECT MALFUNCTIONING PART
Check the Following.
 Check camshaft position sensor (PHASE) and circuit. Refer to EC-223, "
Diagnosis Procedure".
 Check crankshaft position sensor (POS) and circuit. Refer to EC-219, "
Diagnosis Procedure".
Is the inspection result normal?
YES >> GO TO 9.
NO >> 1. Repair or replace malfunctioning part.
2. GO TO 4.
9.CHECK ECM FUNCTION
1. Substitute with a non-malfunctioning ECM to check ECM function. (ECM may be the cause of the incident,
although this is rare.)
2. Perform initialization of NVIS (NATS) system and registration of all NVIS (NATS) ignition key IDs. Refer to
SEC-8, "
ECM RE-COMMUNICATING FUNCTION : Description".
>> GO TO 4.
10.CHECK IGNITION TIMING
1. Run engine at idle.
PBIA8513J