2008 NISSAN TEANA display

AV-38
< ON-VEHICLE REPAIR >[AUDIO SYSTEM]
AUDIO DISPLAY
AUDIO DISPLAY
Exploded ViewINFOID:0000000003765613
Removal and InstallationINFOID:0000000003765614
REMOVAL
1. Remove cluster lid D. Refer to IP-12, "Removal and Installation".
2. Remove audio display unit and A/C display with bracket as a
single unit (1).
3. Remove bracket screws, and then remove audio display unit.
INSTALLATION
Install in the reverse order of removal.
1. Audio display unit 2. Front cover 3. A/C display
4. Bracket
JPNIA1028ZZ
JPNIA1029ZZ

AV
DIAGNOSIS AND REPAIR WORKFLOW
AV-45
< BASIC INSPECTION >[BASE AUDIO AND DISPLAY SYSTEM]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
BASIC INSPECTION
DIAGNOSIS AND REPAIR WORKFLOW
Work FlowINFOID:0000000003882692
OVERALL SEQUENCE
 Reference 1··· Refer to AV-68, "CONSULT-III Function (MULTI AV)".
 Reference 2··· Refer to AV-126, "
DTC Index".
 Reference 3··· Refer to AV-164, "
Symptom Table".
DETAILED FLOW
1.INTERVIEW AND SYMPTOM CONFIRMATION
Check the malfunction symptoms by performing the following items.
 Interview the customer to obtain the malfunction information (conditions and environment when the malfunc-
tion occurred).
 Check the symptom.
Is the occurred symptom malfunction?
YES >> GO TO 2.
NO >> INSPECTION END
2.DIAGNOSIS WITH CONSULT-III
JSNIA0732GB

AV-46
< BASIC INSPECTION >[BASE AUDIO AND DISPLAY SYSTEM]
DIAGNOSIS AND REPAIR WORKFLOW
1. Connect CONSULT-III and perform a self-diagnosis for “MULTI AV”. Refer to AV-68, "CONSULT-III Func-
tion (MULTI AV)".
NOTE:
Skip to step 4 of the diagnosis procedure if “MULTI AV” is not displayed.
2. Check if any DTC is displayed in the self-diagnosis results.
Is DTC displayed?
YES >> GO TO 3.
NO >> GO TO 4.
3.TROUBLE DIAGNOSIS FOR DTC
1. Check the DTC indicated in the self-diagnosis results.
2. Perform the relevant diagnosis referring to the DTC Index. Refer to AV-126, "
DTC Index".
>> GO TO 5.
4.TROUBLE DIAGNOSIS FOR SYMPTOMS
Perform the relevant diagnosis referring to the diagnosis chart by symptom. Refer to AV-164, "
Symptom
Table".
>> GO TO 5.
5.ERROR PART REPAIR
1. Repair or replace the identified malfunctioning parts.
2. Perform a self-diagnosis for “MULTI AV” with CONSULT-III.
NOTE:
Erase the stored self-diagnosis results after repairing or replacing the relevant components if any DTC
has been indicated in the self-diagnosis results.
3. Check that the symptom does not occur.
Does the symptom occur?
YES >> GO TO 1.
NO >> INSPECTION END

AV
INSPECTION AND ADJUSTMENT
AV-47
< BASIC INSPECTION >[BASE AUDIO AND DISPLAY SYSTEM]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
INSPECTION AND ADJUSTMENT
ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL
ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL : De-
scription
INFOID:0000000003882693
WITH AROUND VIEW MONITOR
Always correct the center position of the predicted course line after disconnecting the battery negative termi-
nal.
ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL : Spe-
cial Repair Requirement
INFOID:0000000003882694
1.CORRECTION OF CENTER POSITION OF PREDICTED COURSE LINE
Refer to the following for details.
>> Refer to AV-47, "
PREDICTED COURSE LINE CENTER POSITION ADJUSTMENT : Special
Repair Requirement".
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Description
INFOID:0000000003882695
When camera control unit is replaced, the center position of predicted course line shall be corrected.
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Re-
quirement
INFOID:0000000003882696
1.CORRECTION OF CENTER POSITION OF PREDICTED COURSE LINE
Refer to the following for details.
>> Refer to AV-47, "
PREDICTED COURSE LINE CENTER POSITION ADJUSTMENT : Special
Repair Requirement".
PREDICTED COURSE LINE CENTER POSITION ADJUSTMENT
PREDICTED COURSE LINE CENTER POSITION ADJUSTMENT : Description
INFOID:0000000003882697
Adjust the center position of the possible route line of the rear view monitor if it is shifted.
PREDICTED COURSE LINE CENTER POSITION ADJUSTMENT : Special Repair
Requirement
INFOID:0000000003882698
1.STEERING OPERATION
Steer the steering wheel to the leftmost and rightmost ends.
>> GO TO 2.
2.DRIVING
Drive the vehicle straight ahead 100 m (328.1 ft) or more at a speed of 30 km/h (18.6 MPH) or more.
>> END

AV-48
< FUNCTION DIAGNOSIS >[BASE AUDIO AND DISPLAY SYSTEM]
MULTI AV SYSTEM
FUNCTION DIAGNOSIS
MULTI AV SYSTEM
System DiagramINFOID:0000000003882699
NOTE:
 The name MULTIFUNCTION SWITCH indicates the integration of PRESET SWITCH and MULTIFUNCTION
SWITCH virtually.
 A radio antenna base integrated with radio antenna amp. is adopted.
 Woofer illustrated in the above figure, integrates two woofers and a woofer amp.
System DescriptionINFOID:0000000003882700
Multi AV system means that the following systems are integrated.
 AV control unit controls by transmitting/receiving data one by one with each unit (slave unit) that configures
them completely as a master unit by connecting between units that configure MULTI AV system with two AV
communication lines (H, L).
 Two AV communication lines (H, L) adopt a twisted pair line that is resistant to noise.
 AV control unit is connected by CAN communication, and it receives data signal from ECM, combination
meter. It computes and displays fuel economy information value with the obtained information. Transmitting/
receiving of data signal is performed by BCM. Also, it transmits the required signal of vehicle setting and
receives the response signal.
JSNIA1431GB
System name System explanation
AUDIO SYSTEMAV- 5 3 , "
System Diagram"
REAR VIEW MONITOR SYSTEMAV- 5 6 , "System Description"
VEHICLE INFORMATION SYSTEM Status of audio, climate control system, fuel economy, mainte-
nance and navigation is displayed.
 AV control unit displays the fuel consumption status while re-
ceiving data signal through CAN communication from ECM and
combination meter.
 AV control unit is connected to BCM via CAN communication
transmitting/receiving for the vehicle settings function.
AUXILIARY INPUT SYSTEM Refer to “AUXILIARY INPUT SYSTEM” shown below.

AV
MULTI AV SYSTEM
AV-49
< FUNCTION DIAGNOSIS >[BASE AUDIO AND DISPLAY SYSTEM]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
 AV control unit is connected with display unit and serial communication, and it transmits the required signal
of display and display control and receives the response signal from display unit.
NOTE:
AV control unit can perform CONSULT-III self-operating function and on board self-diagnosis.
 CONSULT-III self diagnosis: Refer to AV-68, "
CONSULT-III Function (MULTI AV)".
 On board self diagnosis: Refer to AV-60, "
Diagnosis Description".
AUXILIARY INPUT SYSTEM
 Image and sound can be output from an external device by connecting a device with auxiliary input jacks.
 Operation can be performed with multifunction switch, steering switch and rear control switch. Multifunction
switch and rear control switch transmits operation signal to AV control unit by AV communication.
JSNIA1432GB

AV-50
< FUNCTION DIAGNOSIS >[BASE AUDIO AND DISPLAY SYSTEM]
MULTI AV SYSTEM
Component Parts Location
INFOID:0000000003882701
1. Front squawker RH 2. Front squawker LH 3. Front door speaker LH
4. Rear door speaker LH 5. Rear control switch 6. Rear view camera
7. Camera control unit 8. Antenna amp. 9. Rear door speaker RH
10. Front door speaker RH 11. Steering angle sensor 12. Steering switch
13. AV control unit 14. Auxiliary input jacks 15. Preset switch
16. Multifunction switch 17. Display unit
A. Trunk room side RH B. Within rear pillar finisher RH C. Spiral cable part
D. In center console
JSNIA1433ZZ

AV
MULTI AV SYSTEM
AV-51
< FUNCTION DIAGNOSIS >[BASE AUDIO AND DISPLAY SYSTEM]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
Component DescriptionINFOID:0000000003882702
Part name Description
AV CONTROL UNIT It is the master unit of the MULTI AV system, and it is connected to each control
unit by communication. It operates each system according to communication
signals from the AV control unit.
 AV control unit includes audio function and vehicle information function.
 It is connected to ECM and combination meter via CAN communication to ob-
tain necessary information for the vehicle information function.
 It is connected to BCM via CAN communication transmitting/receiving for the
vehicle settings function.
 AUX image signal is input from auxiliary jacks.
 Camera image signal is input from camera control unit.
 Composite image (AUX and camera images) signal is output to display unit.
 AUX sound signal is input from the auxiliary jacks.
 Power (signal VCC and inverter VCC) is transmitted to front display unit.
DISPLAY UNIT Display image is controlled by the serial communication from AV control unit.
 It receives the power (signal VCC and inverter VCC) from the AV control unit
and operates.
 RGB image signal is input from AV control unit (RGB, RGB area and RGB syn-
chronizing).
 Composite image (AUX and camera images) signal is input from AV control
unit.
 Synchronize signal (HP, VP) is output to AV control unit.
FRONT SPEAKER Outputs sound signal from front speaker.
 Outputs sound (mid and low range).
REAR SPEAKER Outputs sound signal from rear speaker.
 Outputs sound (mid and low range).
FRONT SQUAWKER Outputs sound signal from front squawker.
 Outputs sound (high and mid range).
MULTIFUNCTION SWITCH Operation panel is equipped with the centralized switch where camera, audio
and auxiliary input operations are integrated.
 The multifunction switch is connected to the preset switch by wiring harness,
and it transmits the operation signal to the preset switch.
PRESET SWITCH Operation panel is equipped with the centralized switch where audio and air
conditioner operations are integrated.
 The preset switch is connected via AV communication, and it transmits the op-
eration signals of the preset switch and multifunction switch.
 The disk ejection operating signal is performed by wiring harness.
CAMERA CONTROL UNIT Camera image signal is input from rear view camera. Camera image signal
output to AV control unit.
 Power supply is transmitted to rear view camera.
 AV control unit recognizes the presence of camera system with camera con-
nection recognition signal.
 Camera control unit is connected via AV communication.
REAR VIEW CAMERA The image of vehicle rear view is transmitted to camera control unit.
 It receives the power supply from the camera control unit and operates.
STEERING ANGLE SENSOR Sensor signal (steering angle) is transmitted to camera control unit.
STEERING SWITCH The operations of audio, etc. can be performed.
 Steering switch signal (operation signal) is output to AV control unit.
AUXILIARY INPUT JACKS The image signal of the auxiliary input is output via the AV control unit to the
display unit.
 The sound signal of the auxiliary input is output via the AV control unit to the
each speaker.