2008 MITSUBISHI LANCER EVOLUTION X trim

GENERAL DESCRIPTION
TSB Revision
INTERIOR52A-2
GENERAL DESCRIPTIONM1521000100429
OPERATION
.
SEAT BELT WARNING SYSTEM
If the driver turns the ignition switch to the "ON" posi-
tion without fastening the seat belt, the seat belt
warning light illuminates.
SPECIAL TOOLM1521000600576
INSTRUMENT PANEL ASSEMBLY
REMOVAL AND INSTALLATIONM1521001701591
WARNING
For removal and installation of the passenger's side air bag module, always observe the ser-
vice procedures described in GROUP 52B, Air Bag Module and Clock Spring P.52B-367.
The following bolts and screws are used for installing the in strument panel. Bolts and screws are indicated as
marks shown in the illustration in the sections of "R emoval and Installation" and "Disassembly and Assem
-
bly."
D: Thread diameter, L: Effective thread length
ToolTool number and nameSupersessionApplication
MB990784
Ornament remover
General service toolRemoval of switch, trim,
etc.
MB990784
NameSymbolSize (D × L) mmColorShape
Tapping screwa5 × 12−
b5 × 16−
c5 × 12−
Bolt with washerd5 × 20−
e6 × 16−
AC104450
AC104436
AC104417
AC104429

INSTRUMENT PANEL ASSEMBLY
TSB Revision
INTERIOR52A-3
CAUTION
•Refer to GROUP 52B-SRS Service Precautions P.52B-24 and Air bag Module and Clock Spring
P.52B-367 before removing the passenger side air bag module.
•Do not subject the SRS-ECU to any shocks when removing or installing the instrument panel.
Pre-removal and Post-installation Operation
•Removal and Installation of Front Pillar Trim (Refer to P.52A-10).
•Removal and Installation of Instrument Under Cover
(Refer to P.52A-10).
•Removal and Installation of Glove Box (Refer to P.52A-10).
•Removal and Installation of Instrument Cover Lower, Air
Outlet Garnish (Refer to P.52A-10).
•Removal and Installation of Audio Unit (Refer to GROUP
54A, Radio with CD Player P.54A-307).
•Removal and Installation of Audio Visual Navigation Unit,
GPS antenna (Refer to GROUP 54A, MMCS P.54A-391).
•Removal and Installation of Steering shaft (Refer to
GROUP 37, Steering Column Shaft P.37-25).
•Removal and Installation of Hands-free Cellular Phone
System (Refer to GROUP 54A, Hands-free Module
P.54A-435).
•Removal and Installation of Sensors (Refer to GROUP
55B, Interior Temperature Sensor
P.55B-25).

TRIMS
TSB Revision
INTERIOR52A-10
TRIMS
REMOVAL AND INSTALLATIONM1521001101049
Required Special Tool:
•MB990784: Ornament Remover
AC610310
45
1 3
6
2 79
11
12
10
13
AB
8
14
22 ± 4 N·m
16 ± 3 ft-lb
Removal steps
1.Front scuff plate
2.Cowl side trim
•Rear seat cushion (Refer
to
P.52A-23).
3.Rear scuff plate
4.Front door opening trim
5.Rear door opening trim
<>6.Front pillar trim
7.Lower center pillar trim
8.Upper center p illar trim cap
•Outer seat belt (Refer toP.52A-28).
9.Upper center pillar trim
10.Rear pillar trim
•Seat side back (Refer toP.52A-23).
11 .Rear shelf trim
12.Rear end trim
13.Trunk side trim
14.Child restraint fitting
Removal steps (Continued)

TRIMS
TSB Revision
INTERIOR52A-11
CLIP POSITION
NOTE: Each number in the illustration indicates a
part number.
AC610026AB
Note
: Clip positions
: Claw positions
Section A – A Section B – B Section C – C Section D – D
Section E – E Section F – F Section G – G Section H – H
Section I – I Section J – J Section K – K Section L – L Claw
Clip
Clip
Clip
Clip
Claw
Clip
Claw
Claw
Claw
Clip
Claw
Claw
A
B
B A
C
E
E
B DD
C A
B
J
J
KL
L
K
B
AB
F
F
G
G H
I
I I
H H
H
I
6, 10
6, 7, 10
99
7
7
1, 3
2
1212111, 3

TRIMS
TSB Revision
INTERIOR52A-12
REMOVAL SERVICE POINT
.
<> UPPER CENTER PILLAR TRIM CAP
REMOVAL
Remove the opening trim. Remove the upper center pillar trim
cap by inserting the special tool MB990784 between the upper
center pillar trim and body as shown in the illustration.
AC606516
A
A
MB990784
AIMB990784
Section A – A
Upper center
pillar trim cap

DOOR TRIM
TSB Revision
INTERIOR52A-13
DOOR TRIM
REMOVAL AND INSTALLATIONM1521006400752
Required Special Tool:
•MB990784: Ornament Remover
AC611164
15
7
12 6
2
8
9
10 11
3
4
A
Section A – A
Note
: Clip positions

A
Clip
Front door trim
assembly
AB
Removal steps
1.Front door trim assembly
2.Front door ornament
3.Front door pocket
4.Front lower pad energy absorption
5.Front door trim upper
6.Door inside handle
7.Decoration panel
8.Front door power window switch
panel assembly
9.Remote control mirror switch
10.Front door power window switch
11 .Front power window switch panel
12.Front door trim lower
Removal steps (Continued)

DOOR TRIM
TSB Revision
INTERIOR52A-14
Required Special Tool:
•MB990784: Ornament Remover
AC611175
A
ASection A – A
Clip
Rear door trim
assembly
16
11 2
3
8
10
9 5
4
NOTE : Clip positions

AB
7
Removal steps
1.Rear door trim assembly
2.Rear upper pad energy absorption
3.Rear door ornament
4.Rear door pocket
5.Rear lower pad energy absorption
6.Rear door trim upper
7.Door inside handle
8.Rear door powe r window switch
panel assembly
9.Rear door powe r window switch
10.Rear power window switch panel
11 .Rear door trim lower
Removal steps (Continued)

HEADLINING
TSB Revision
INTERIOR52A-15
HEADLINING
REMOVAL AND INSTALLATIONM1521001400973
Pre-removal and Post-installation Operation
•Removal and Installation of Front Pillar Trim, Upper Cen-
ter Pillar Trim, Rear Pillar Trim (Refer to P.52A-10).
•Removal and Installation of Instrument Under Cover
(Refer to
P.52A-6).
AC609656
2
6
1
1
1
1
3 4
45
5
7
7
8
8
9 8
9 10
10
8
AB
A
A
Section A – AClip
Claw
8
3


Note
(1) : Clip positions
(2) : Claw positions