2008 MERCEDES-BENZ SL65AMG turn signal

410 Practical hints
Replacing bulbs
Front lamps Rear lamps
LampType
1 Additional turn signalLED
2Turn signal lamp1156 NA
3Low beam1,2
1Vehicles with Bi-Xenon* headlamps: Low beam
and high beam use the same D2S-35W lamp.
2Vehicles with Bi-Xenon* headlamps: Do not
replace the Xenon and Bi-Xenon* bulbs yourself.
Contact an authorized Mercedes-Benz Center.
D2S-35W
4Xenon headlamp:
High beam, high beam
flasherH7 (55 W)
Bi-Xenon headlamp*:
High beam flasherH7 (55 W)
Parking and standing
lampW 5 W
5Front fog lamp,
Corner-illuminating
front fog lamp*H11 (55 W)
6Side marker lampW 5 W
LampType
7 Rear fog lamp
(driver’s side only)P 21 W
8 High mounted brake
lampLED
9 Backup lampP 21 W
a Tail, parking and
standing lamp, side
marker lampLED
b Brake lampLED
c License plate lampC 5 W
d Turn signal lampPY 21 W

411 Practical hints
Replacing bulbs
Notes on bulb replacement

Only use 12-volt bulbs of the same type
and with the specified watt rating.

Switch the lights off before changing a
bulb to prevent short circuits.

Always use a clean lint-free cloth when
handling bulbs.

Your hands should be dry and free of oil
and grease.

If the newly installed bulb does not
come on, visit an authorized
Mercedes-Benz Center.Have the LEDs and bulbs for the following
lamps replaced by an authorized
Mercedes-Benz Center:

the additional turn signals in the
exterior rear view mirrors

the high mounted brake lamp

the brake lamps

the parking lamps and the side marker
lamps in the tail lamp unit

the rear fog lamps

the low beam (Xenon or Bi-Xenon*)
lamps

the front fog lamps

the front side marker lamps
Replacing bulbs for front lamps
Before you start to replace a bulb for a
front lamp, do the following first:
Turn the exterior lamp switch to
position M (
page 131).
Open the hood (page 282).
1Bulb socket for turn signal lamp
2High beam headlamp cover
3Low beam headlamp cover (Xenon or
Bi-Xenon* lamp). Do not remove.
!Do not replace the LEDs yourself. You could
otherwise damage the LEDs or parts of the
vehicle. Only have the LEDs replaced by an
authorized Mercedes-Benz Center.

412 Practical hints
Replacing bulbs
4High beam bulbs
5Locking mechanism
6Parking and standing lampsFront turn signal bulb
Turn bulb socket 1 (page 411)
counterclockwise and pull it out.
Push the bulb into socket 1, turn
socket 1 counterclockwise and
remove it.
Insert the new bulb in bulb socket 1,
push and turn bulb socket 1 clock-
wise.
Reinsert bulb socket 1 in lamp hous-
ing and turn bulb socket 1 clockwise.High beam/high beam flasher bulbs
Press ends of headlamp cover tab
together and remove high beam head-
lamp cover 2 (
page 411).
Pull the electrical connector off.
Turn locking mechanism 5 counter-
clockwise and take out the bulb.
Insert the new bulb so that the base
locates in the recess on the holder.
Turn locking mechanism 5 clockwise.
Plug the connector onto the bulb.
Align high beam headlamp cover 2
and click it into place.Warning!G
Do not remove the cover for the Xenon or
Bi-Xenon* headlamp. Because of high
voltage in Xenon and Bi-Xenon* lamps, it is
dangerous to replace the bulb or repair the
lamp and its components. We recommend
that you have such work done by a qualified
technician.

413 Practical hints
Replacing bulbs
Parking and standing lamp bulbs
Press ends of headlamp cover tab
together and remove high beam
headlamp cover 2.
Pull out bulb socket 6 with the bulb.
Pull the bulb out of bulb socket 6.
Insert a new bulb in bulb socket 6.
Reinstall bulb socket 6.
Align high beam headlamp cover 2
and click it into place.Additional turn signal lamp bulbs
The additional turn signal lamps in the
exterior rear view mirrors have LEDs.
If a malfunction occurs or LEDs fail to func-
tion, the entire turn signal unit must be re-
placed. Have the turn signal unit replaced
by an authorized Mercedes-Benz Center.Front side marker lamp bulbs
Since replacing the side marker lamp bulbs
is a technically highly demanding process,
we recommend you have the side marker
lamp bulbs replaced by an authorized
Mercedes-Benz Center.

414 Practical hints
Replacing bulbs
Replacing bulbs for rear lamps
Before you start to replace a bulb for a rear
lamp, do the following first:
Turn the exterior lamp switch to
position M (
page 131).
Open the trunk (page 114).
Tail lamp unit
1Backup lamp
2Driver’s side: Rear fog lamp
Passenger’s side: Substitute lamp
3Turn signal lamp
Fold the trim to the side and remove it.
Turn the bulb socket counterclockwise
and pull it out.
Gently push the bulb into the socket,
turn it counterclockwise and remove it.
Insert the new bulb and reinstall the
bulb socket.
The bulb socket should audibly click
into place.
Reinstall the trim.License plate lamp
1Screws
Loosen both screws 1.
Remove the license plate lamp.
Replace the bulb.
Reinstall the license plate lamp.
Retighten screws 1.

435 Practical hints
Towing the vehicle
!If the vehicle is towed with the front axle
raised, the gear selector lever must be in
positionN and the engine must be shut off
(SmartKey in starter switch position0 or1).
Active braking action through the ESP
® may
otherwise seriously damage the brake system.
When towing the vehicle with all wheels on the
ground, the gear selector lever must be in
positionN and the SmartKey must be in starter
switch position2.
When towing the vehicle with all wheels on the
ground or the front axle raised, the vehicle
may be towed only for distances up to
30 miles (50 km) and at a speed not to exceed
30 mph (50 km/h).
!Towing of the vehicle should only be done
using the properly installed towing eye bolt.
Never attach a tow cable, tow rope or tow rod to
the vehicle chassis, frame or suspension parts.
iWhen towing the vehicle with all wheels on
the ground, please note the following:
With the automatic central locking activated and
the SmartKey in starter switch position2, or
KEYLESS-GO* start/stop button in position2,
the vehicle doors lock if the left front wheel as
well as the right rear wheel are turning at vehicle
speeds of approximately 9 mph (15 km/h) or
more.
To prevent the vehicle door locks from locking,
deactivate the automatic central locking
(
page 122).
iTo signal turns while being towed with the
hazard warning flasher in use, turn SmartKey in
starter switch to position2 and activate the
combination switch for the left or right turn
signal in the usual manner – only the selected
turn signal will operate.
Upon canceling the turn signal, the hazard warn-
ing flasher will operate again.
iIf the battery is disconnected or discharged

the SmartKey will not turn in the starter
switch

the gear selector lever will remain locked in
positionP.
For more information, see “Batteries”
(
page 427) and “Jump starting” (page 432).

469 Index
Brake system
Messages in the multifunction
display 382
Brakes 268
BAS 91
Brake fluid 280, 458, 460
Electro-hydraulic brake system 94
High-performance brake system
(AMG vehicles only) 270
Warning lamp 345
Break-in period 266
Bulbs
Messages in the multifunction
display 392
Replacing 409
C
California retail buyers and lessees,
important notice for 11
Call priority, Tele Aid 256
Capacities and recommended
fuel/lubricants 457
Cargo area see Trunk
Carpets, cleaning 339
Catalytic converter 277
CD changer 155, 240CD player
Operating 155
Center console
Lower part 32
Upper part 31
Central locking
Automatic 122, 166
Central locking/unlocking
switch 31, 122
Locking/unlocking from inside 122
Certification label 444
Check engine see Lamps, indicator and
warning
Checking tire pressure electronically with
the Advanced Tire Pressure Monitoring
System (Advanced TPMS)*, (Canada
only) 308
Children in the vehicle
Air bags 84
Infant and child restraint systems 84
Occupant Classification System
(OCS) 74
Passenger front air bag off indicator
lamp 78, 357
Cigarette lighter 244
Clock 25, 161Cockpit 24
Cold tire inflation pressure 323
Collapsible tire (spare wheel) 453
COMAND system 31
Driving instructions 276
Combination switch
High beam 57, 135
Turn signals 57
Windshield wipers 58
Consumer battery 290
Control and operation of radio
transmitters 276
Control system 143, 146
Control system menus
AMG 150
AUDIO 153
Distronic* 156, 222
NAV 155
Settings 157
Standard display 149
TEL* 169
Trip computer 167
Vehicle status message memory 156

475 Index
Key, SmartKey with KEYLESS-GO* 108
Batteries 407
Battery check lamp 108
Checking the batteries 113
Factory setting 111
Global locking 111, 112
Global unlocking 111, 112
Locking/unlocking 39, 65, 108
Loss of 113
Messages in the multifunction
display 390, 391
Opening, Trunk 115
Opening/closing retractable
hardtop 206
Remote control 108
Replacing batteries 407
Reprogramming 112
Restoring to factory settings 112
Selective setting 112
Starter switch positions 41
Starting the engine 54
Turning off the engine 64
Unlocking, Trunk lid 114KEYLESS-GO*
Closing windows 203
Important notes 109
Locking/unlocking 39, 65, 108
Messages in the multifunction
display 390
Start/stop button 31, 41, 54
Starter switch positions 41
Starting the engine 54
Turning off the engine 64
Unlocking, Trunk lid 114
Kickdown 175
Kilopascal 323
Knee bag 74
L
Labels, identification 444
Lamp bulbs, exterior 409
Lamps, exterior
Delayed switch-off 164
Exterior lamp switch 25, 57
Front 410
Light sensor 392
Replacing bulbs for rear 410, 414
Switching off 131
Switching on 131Lamps, indicator and warning
ABS 29, 344
ABS/ESP
®342
Brakes 345
CHECK ENGINE 346, 347
Coolant 348
Distronic* indicator and warning
lamp 27, 221
Electro-hydraulic brake system 94
Engine diagnostics 346, 347
Engine malfunction 29
ESP
®91
Fuel reserve 350
Passenger front air
bag off 74, 78, 357
Seat belt telltale 352
Seat belts 352–353
SRS 69, 354
Turn signals 27
Language
Multifunction display 160
Leather upholstery
Cleaning 340
License plate lamps 163, 410, 414
Light alloy wheels, cleaning 338