2008 MERCEDES-BENZ SL600 change time

58 Getting started
Driving
The combination switch resets automati-
cally after major steering wheel move-
ments.Windshield wipers
The combination switch is located on the
left of the steering column.
Combination switch
1Switching on windshield wipers
2Single wipe
Wiping with windshield washer fluid
Switch on the ignition (page 40).
iTo signal minor directional changes such as
changing lanes, press combination switch only
to point of resistance and release.
The corresponding turn signals will flash three
times.
!Do not operate the windshield wipers when
the windshield is dry. Dust that accumulates on
a windshield might scratch the glass and/or
damage the wiper blades when wiping occurs on
a dry windshield. If it is necessary to operate the
windshield wipers in dry weather conditions,
always operate the windshield wipers with
windshield washer fluid (
page 60).
!If anything blocks the windshield wipers
(leaves, snow, etc.), switch them off imme-
diately.

For safety reasons, stop the vehicle in a safe
location and

remove the SmartKey from the starter
switch
or

turn off the engine by pressing the
KEYLESS-GO* start/stop button and
open the driver’s door (with the driver’s
door open, the starter switch is in
position 0, same as with the SmartKey
removed from the starter switch)
before attempting to remove any blockage.

Remove blockage.

Turn the windshield wipers on again.

59 Getting started
Driving
Switching on windshield wipers
Turn the combination switch in
direction of arrow 1 to the desired
position, depending on the intensity of
the rain.
0Windshield wipers off
IIntermittent wiping
IINormal wiper speed
IIIFast wiper speedIntermittent wiping
Only switch on intermittent wiping under
wet weather conditions or in the presence
of precipitation.
Turn the combination switch in
direction of arrow 1 to positionI.
After the initial wipe, pauses between
wipes are automatically controlled by the
rain sensor.Single wipe
Press the combination switch briefly in
direction of arrow2 (
page 58) to
the resistance point.
The windshield wipers wipe one time
without washer fluid.
If the windshield wipers fail to function at all with
the combination switch in positionI,

set the combination switch to the next
higher wiper speed

have the windshield wipers checked at the
nearest authorized Mercedes-Benz Center
!Do not leave windshield wipers on an inter-
mittent setting when the vehicle is taken to an
automatic car wash or during windshield clean-
ing. Windshield wipers will operate in the pres-
ence of water sprayed on the windshield, and
windshield wipers may be damaged as a result.
!If you have set intermittent wiping, dirt on
the surface of the rain sensor or optical effects
may cause the windshield wipers to wipe in an
undesired fashion. This could then damage the
windshield wiper blades or scratch the wind-
shield. You should therefore switch off the wind-
shield wipers when weather conditions are dry.
iIntermittent wiping is interrupted when the
vehicle is at a standstill and a door is opened.
This protects persons getting into or out of the
vehicle from being sprayed.
Intermittent wiping will be continued when

all doors are closed
and

the gear selector lever is in positionDorR
or

the wiper setting is changed using the
combination switch

72 Safety and Security
Occupant safety
Safety guidelines for the seat belt,
emergency tensioning device and
air bag
In case of other types of impacts and impacts be-
low air bag deployment thresholds, air bags will
not deploy. The driver and passenger will then be
protected to the extent possible by a properly
fastened seat belt. A properly fastened seat belt
is also needed to provide the best possible
protection in a rollover.
We caution you not to rely on the presence of the
air bags in order to avoid wearing your seat belt.
It is important to your safety and that of your pas-
senger that you replace deployed air bags and
repair any malfunctioning air bags to make sure
that the vehicle will continue to provide supple-
mental crash protection for occupants.
Warning!G

Damaged seat belts or seat belts that
were highly stressed in an accident
must be replaced and their anchoring
points must also be checked. Only use
seat belts installed or supplied by an
authorized Mercedes-Benz Center.

Air bags and Emergency Tensioning
Devices (ETDs) contain Perchlorate
material, which may require special han-
dling and regard for the environment.
Check with your local government’s
disposal guidelines. California residents,
see http://www.dtsc.ca.gov/Hazard-
ousWaste/Perchlorate/index.cfm.

Air bags and Emergency Tensioning
Devices (ETDs) are designed to function
on a one-time-only basis. An air bag or
ETD that has deployed must be re-
placed.

Do not pass seat belts over sharp edges.
They could tear.

Do not make any modification that could
change the effectiveness of the seat
belts.

Do not bleach or dye seat belts as this
may severely weaken them. In a crash,
they may not be able to provide ade-
quate protection.

No modifications of any kind may be
made to any components or wiring of
the SRS. This includes changing or
removing any component or part of the
SRS, the installation of additional trim
material, badges, etc. over the steering
wheel hub, passenger front air bag
cover, door frame trims, or door trim
panels, and installation of additional
electrical/electronic equipment on or
near SRS components and wiring. Keep
area between air bags and occupants
free from objects (e.g. packages,
purses, umbrellas, etc.).

Air bag system components will be hot
after an air bag has inflated. Do not
touch.

Never place your feet on the instrument
panel, dashboard, or on the seat. Always
keep both feet on the floor in front of the
seat.

85 Safety and Security
Occupant safety
Infant and child restraint systems
We recommend all infants and children be
properly restrained at all times while the
vehicle is in motion.
The passenger lap-shoulder belt has a
special seat belt retractor for secure fas-
tening of child restraints.
To fasten a child restraint follow child re-
straint instructions for mounting. Then pull
the shoulder belt out completely and let it
retract. During seat belt retraction, a ratch-
eting sound can be heard to indicate that
the special seat belt retractor is activated.
The seat belt is now locked. Push down on
child restraint to take up any slack.
To deactivate, release seat belt buckle
and let seat belt retract completely. The
seat belt can again be used in the usual
manner.The use of infant or child restraints is re-
quired by law in all 50 states, the District of
Columbia, the U.S. territories, and all
Canadian provinces.
Infants and small children should be
seated in an appropriate infant or child
restraint system which is properly secured
by a lap-shoulder belt and that complies
with U.S. Federal Motor Vehicle Safety
Standards 213 and 225 and Canadian
Motor Vehicle Safety Standards 213 and
210.2.
A statement by the child restraint manu-
facturer of compliance with this standard
can be found on the instruction label on
the restraint and in the instruction manual
provided with the restraint.Do not expose the child restraint system to
direct sunlight. The child restraint system’s
metal parts, for example, could become very
hot, and the child could be burned on these
parts.
If children open a door, they could

injure other persons

get out of the car and injure themselves
or be injured by following traffic
Do not carry heavy or hard objects in the
passenger compartment unless they are
firmly secured in place.
For more information, please refer to the
“Useful features” section (
page 238)
through (
page 243).
Unsecured or improperly positioned cargo
increases a child’s risk of injury in the event
of

strong braking maneuvers

sudden changes of direction

an accident
Warning!G
Never release the seat belt buckle while the
vehicle is in motion, since the special seat
belt retractor will be deactivated.

110 Controls in detail
Locking and unlocking

To lock or unlock the vehicle, the
SmartKey with KEYLESS-GO must be
located outside the vehicle within ap-
proximately 3 ft (1 m) of a door or the
trunk.

If the vehicle has been parked for more
than 72 hours, you must pull an outside
door handle in order to activate the
KEYLESS-GO function.

In order to start the engine with the
SmartKey with KEYLESS-GO:

The SmartKey with KEYLESS-GO
must be located in the vehicle.

All doors must be closed.

The brake pedal must be firmly
depressed. Do not depress the
accelerator.

If you have started the engine with the
KEYLESS-GO start/stop button
(
page 41), you can only turn it off
again with this button, even if you have
put the SmartKey in the starter switch
in the meantime.

This does not apply if, after starting, the
selector lever is still in positionP and
the SmartKey is then inserted in the
starter switch. The SmartKey will then
have priority over the KEYLESS-GO
function and the vehicle’s electrical
system will operate according to the
position of the SmartKey in the starter
switch, even stopping the engine.

If the SmartKey with KEYLESS-GO is
positioned farther away from the vehi-
cle, the system may no longer recog-
nize the SmartKey with KEYLESS-GO.
The vehicle then cannot be locked or
the engine started via the KEYLESS-GO
system.

If the SmartKey with KEYLESS-GO is re-
moved from the vehicle while the en-
gine is running (e.g. if passenger exits
the vehicle with the SmartKey with
KEYLESS-GO), the message
Key Not
Detected
will appear in the multifunc-
tion display while driving off.Find the SmartKey or change its
present location immediately (e.g.
place it on the passenger seat or insert
it in shirt pocket).

Remember that the engine can be
started by anyone with a SmartKey
with KEYLESS-GO that is left inside the
vehicle. If you leave the SmartKey with
KEYLESS-GO behind when exiting and
locking the vehicle, the message
Key
Detected In Vehicle
will appear in the
multifunction display.

158 Controls in detail
Control system
Resetting all settings
You can reset the functions of most of the
submenus to the factory settings.
For safety, the
Light Circuit Headlamp
Mode
submenu in the Lighting menu can
be reset with the vehicle at standstill only.
Press button è or ÿ repeatedly
until the
Settings menu appears in the
multifunction display.
Press the reset button in the instru-
ment cluster for approximately
3 seconds.
In the right multifunction display you
will see the request to press the reset
button again to confirm.
Press the reset button again.
The functions of most submenus will
reset to factory settings.
Submenus in the Settings menu
Press button è or ÿ repeatedly
until the
Settings menu appears in the
multifunction display.
Press button j.
In the right multifunction display you
see the collection of submenus. There
are more submenus than can be simul-
taneously displayed.
Press button ç.
The selection marker moves to the next
submenu.
Scroll down with the ç button,
scroll up with the æ button.
With the selection marker on the de-
sired submenu, use the j button to
access the individual functions within
that submenu.
Once within the submenu, use
thej button to move to the next
function or the k button to move to
the previous function within that sub-
menu.
Use buttons æ or ç to change
the settings of the respective function.
iThe settings you have changed will not be
reset unless you confirm the action by pressing
the reset button a second time.

159 Controls in detail
Control system
The table below shows what settings can
be changed within the various menus.
Detailed instructions on making individual
settings can be found on the following
pages.
Instrument clusterTimeLightingVehicleConvenience
(page 160)(page 161)(page 163)(page 166)(page 166)
Selecting speedometer
display modeSynchronizing time with
head unitSetting daytime running
lamp mode (USA only)Setting automatic lockingActivating
easy-entry/exit feature
Selecting standard
displaySetting the time (hour)Setting locator lighting
Selecting languageSetting the time
(minutes)Setting night security
illumination
Setting interior lighting
delayed switch-off

161 Controls in detail
Control system
Press button æ or ç to select
the language to be used for the
multifunction display messages.
Available languages:

German

English

French

Italian

Spanish

Dutch

Swedish

Danish

Turkish

PortugueseSelecting standard display
Move the selection marker with
buttonæ or ç to the
Inst. Cluster submenu.
Press button j or k repeatedly
until the message
Select Display ap-
pears in the multifunction display.
The selection marker is on the current
setting.
Press button æ or ç to select
the desired setting.
The selected option appears in the left
multifunction display.
The option not selected will appear in
the right multifunction display when
scrolling through the standard display
(
page 149).Time submenu
Access the
Time submenu via the Settings
menu. Use the
Time submenu to change
the time and date settings. The following
functions are available:
Synchronizing time with head unit
Move the selection marker with
theæ or ç button to the
Time
submenu.
Press button j or k repeatedly
until the message
Time Synchron.
With Head Unit
appears in the multi-
function display.
The selection marker is on the current
setting.
FunctionPage
Synchronizing time with head
unit161
Setting the time (hour)162
Setting the time (minutes)162