402 Practical hints
Where will I find ...?
Storing the spare wheel after use
If you wish to store the spare wheel after
use, carry out the following steps. Other-
wise, the spare wheel may not fit the spare
wheel well.
Unscrew the valve cap from the valve
of the collapsible tire.
Take the valve extractor from the
vehicle tool kit (
page 400).
Unscrew the valve insert from the valve
and allow the air to escape.
Screw the valve insert back into the
valve.
Screw the valve cap back onto the
valve.
Store the spare wheel by carrying out
the steps described in “Removing the
spare wheel” (
page 401) in reverse
order.
Compressing the collapsible tire
(vehicles with 19" spare wheel only)
The collapsible tire on a 19" spare wheel
must be compressed with two tensioning
straps before you can store it back in the
trunk.
Extend the tensioning strap by pulling
the slider.
Place tensioning strap around spare
wheel rim and collapsible tire with the
buckle facing the inside of the rim.
Close the buckle.
Pull the loose end of the tensioning
strap.
The tensioning strap must be pulled as
tight as possible.
!Make sure the spare wheel is dry before
storing it.
iIt may take a few minutes for the collapsible
tire to deflate completely.
iVehicles with 19" spare wheel only: Before
storing the spare wheel in trunk fasten tension-
ing straps, see “Compressing the collapsible tire
(vehicles with 19" spare wheel only)”
(
page 402).
iThe tensioning straps are shown in red for
illustration purposes. The tensioning straps on
the spare wheel of your vehicle are black.
417 Practical hints
Flat tire
Flat tire
Preparing the vehicle
Park the vehicle in a safe distance from
moving traffic on a hard, flat surface
when possible.
Turn on the hazard warning flashers.
Turn the steering wheel so that the
front wheels are in a straight ahead
position.
Set the parking brake (page 63).
Move the gear selector lever to
position P.
Turn off the engine (page 64).
Have any passenger exit the vehicle at
a safe distance from the roadway.
Vehicles with Smartkey: Remove the
SmartKey from the starter switch.
Vehicles with KEYLESS-GO*: Open the
driver’s door (this puts the starter
switch in position 0, same as with the
SmartKey removed from the starter
switch). The driver’s door then can be
closed again.Mounting the spare wheel
iOpen door only when conditions are safe to
do so.
Warning!G
The dimensions of the spare wheel are dif-
ferent from those of the road wheels. As a
result, the vehicle handling characteristics
change when driving with a mounted spare
wheel. Adapt your driving style accordingly.
The spare wheel is for temporary use only.
When driving with spare wheel mounted, en-
sure proper tire inflation pressure and do
not exceed vehicle speed of 50 mph
(80 km/h).
Drive to the nearest Mercedes-Benz Center
as soon as possible to have the spare wheel
replaced with a regular road wheel.
Never operate the vehicle with more than
one spare wheel mounted.
Do not switch off the ESP
® when a spare
wheel is mounted.
418 Practical hints
Flat tire
Preparing the vehicle
Prepare the vehicle as described
(
page 417).
Turn spare wheel bracket counter-
clockwise to loosen.
Take the spare wheel out of the trunk
(
page 401).
Removing tensioning straps
(vehicles with 19" spare wheel only)
A 19" spare wheel has two tensioning
straps on it that must both be removed be-
fore mounting the spare wheel.1Buckle
2Clip
Press on both clips 2 simultaneously
to release buckle 1.Lifting the vehicle
Prevent the vehicle from rolling away
by blocking wheels with wheel chocks
(not included) or other sizeable
objects.
When changing wheel on a level
surface:
Place one wheel chock or other
sizeable object in front of and
another wheel chock or sizeable
object behind the wheel that is
diagonally opposite to the wheel
being changed.
Always try lifting the vehicle using the
jack on a level surface. However,
should circumstances require you to do
so on a hill, place a wheel chock or
other sizeable object and the other
wheel chock or sizeable object as
follows:
Place wheel chocks or other size-
able objects on the downhill side
blocking both wheels of the axle not
being worked on.
iThe tensioning straps are shown in red for
illustration purposes. The tensioning straps on
the spare wheel of your vehicle are black.iKeep the tensioning straps in a safe place.
You will need them to store the spare wheel in
the trunk after use (
page 402).
421 Practical hints
Flat tire
Keeping jack in this position, turn
crank3 clockwise until the jack base
meets the ground. Make sure the jack
is vertical (plumb line).
Continue to turn the crank until the tire
is a maximum of 1.2 in (3 cm) from the
ground.Removing the wheel
1Alignment bolt
Unscrew upper-most wheel bolt and
remove.
Replace this wheel bolt with alignment
bolt1 supplied in the tool kit.
Remove the remaining bolts.
Remove the wheel.Mounting the new wheel
Clean contact surfaces of wheel and
wheel hub.
Guide the spare wheel onto the align-
ment bolt and push it on.
Insert wheel bolts and tighten them
slightly.
!Do not place wheel bolts in sand or dirt. This
could result in damage to the bolt and wheel hub
threads.
Warning!G
Inflate spare wheel tire only after the wheel
is properly mounted.
Inflate the spare wheel tire using the
electric pump (
page 422) before lowering
the vehicle.
422 Practical hints
Flat tire
Unscrew the alignment bolt, install last
wheel bolt and tighten slightly.
Inflating the spare tire (collapsible tire)
Take the electric air pump out of the
trunk (
page 400).1Flap
2Air pump switch
3Electrical plug
4Air hose with pressure gauge and vent
screw
5Union nut
Open flap 1 on air pump.
Pull out electrical plug 3 and air hose
with the pressure gauge 4.
Remove the valve cap from the tire
valve.
Screw union nut 5 onto the tire valve.
Warning!G
Always replace wheel bolts that are dam-
aged or rusted.
Never apply oil or grease to wheel bolts.
Damaged wheel hub threads should be
repaired immediately. Do not continue to
drive under these circumstances! Contact
an authorized Mercedes-Benz Center or call
Roadside Assistance.
Incorrect wheel bolts or improperly tight-
ened wheel bolts can cause the wheel to
come off. This could cause an accident. Be
sure to use the correct wheel bolts.
Warning!G
Only use genuine Mercedes-Benz wheel
bolts. They are identified by the Mercedes
star. Other wheel bolts may come loose.
Do not tighten the wheel bolts when the ve-
hicle is raised. Otherwise the vehicle could
fall off the jack.
!Do not lower the vehicle before inflating the
spare wheel tire. Otherwise the rim may be dam-
aged.
Warning!G
Observe instructions on air pump label.
423 Practical hints
Flat tire
Insert electrical plug 3 into vehicle
cigarette lighter socket (
page 244)
or the power outlet in the trunk
(
page 246).
Turn the SmartKey in the starter switch
to position1.
or
Press the KEYLESS-GO* start/stop
button on the gear selector lever once
without depressing the brake pedal.
PressI on the electric air pump
switch2.
The electric air pump should now
switch on and inflate the tire.
Inflate the spare tire:
SL 550 to 36 psi (2.5 bar)
SL 600, SL 55 AMG, SL 55 AMG
(Performance Package*), and
SL 65 AMG to 51 psi (3.5 bar)
This takes about 5 minutes.
Air hose4 and union nut5 can be-
come hot during inflation. Exercise
proper caution to avoid burning your-
self when using the equipment.
Press0 on the electric air pump
switch2.
Turn the SmartKey in the starter switch
to position0.
or
Press KEYLESS-GO* start/stop button
on the gear selector lever twice without
depressing the brake pedal.
The electric air pump should now be
switched off.
If the spare tire inflation pressure is
above the recommended tire inflation
pressure for the respective collapsible
tire (
page 453), release excess spare
tire inflation pressure using the vent
screw.
!Compare the recommended tire inflation
pressure for your vehicle with the tire inflation
pressure on the yellow label located on the spare
wheel rim.
If the tire inflation pressure on the yellow label
on the spare wheel rim differs from the values
given in this Operator’s Manual, inflate the tire to
the recommended tire inflation pressure given
on the yellow label on the spare wheel rim.
!Do not operate the electric air pump longer
than 8 minutes without interruption. Otherwise it
may overheat.
You may operate the air pump again after it has
cooled off.
424 Practical hints
Flat tire
Detach the electric air pump.
Stow the electrical plug and the air
hose behind the flap and place the air
pump back in the trunk.
Lowering the vehicle
Lower vehicle by turning crank coun-
terclockwise until the full weight of the
vehicle is resting on the ground.
Pull the jack out of the jack support
tube.1 - 5 Wheel bolts
Tighten the five wheel bolts evenly,
following the diagonal sequence
illustrated (1 to 5), until all bolts
are tight. Observe a tightening torque
of 96 lb-ft (130 Nm).
Warning!G
Follow recommend inflation pressures.
Do not overinflate tires. Overinflating tires
can result in sudden deflation (blowout) be-
cause they are more likely to become punc-
tured or damaged by road debris, potholes,
etc.
Do not underinflate tires. Underinflated tires
wear unevenly, adversely affect handling
and fuel economy, and are more likely to fail
from being overheated.
Do not overload the tires by exceeding the
specified load limit as indicated on the Tire
and Loading Information placard on the
driver’s door B-pillar. Overloading the tires
can overheat them, possibly causing a
blowout. Overloading the tires can also
result in handling or steering problems, or
brake failure.
iThe flat tire may be transported in the trunk
when the retractable hardtop is raised. If avail-
able, use a protective sheet on the spare wheel.
Vehicles with TPMS or Advanced TPMS*:
Do not activate the tire inflation pressure moni-
tor until a full size wheel/tire with functioning
sensor has been placed back into service on the
vehicle.
Warning!G
Have the tightening torque checked after
changing a wheel. The wheels could come
loose if they are not tightened to a torque of
96 lb-ft (130 Nm).
425 Practical hints
Flat tire
Before storing the jack in the trunk,
crank back to storage position and fold
in the arm.Replacing jack support tube cover
Slide tongue of cover under the upper
edge of the tube opening.
Applying even pressure, press cover
until it snaps into place.
Be careful not to damage the locking
tabs or clamp the plastic retaining
strap.
MOExtended system*
The MOExtended system allows you to
continue driving your vehicle even if there
is a total loss of pressure in one or more
tires.
You may only use the MOExtended system
in conjunction with the Run Flat Indicator*
(Canada vehicles) (
page 303), TPMS
(U.S. vehicles) (
page 305), or Advanced
TPMS* (Canada vehicles) (
page 308).
Warning!G
When turning the wheel wrench to tighten
the wheel bolts, make sure you position
hands on the wrench in such a way that you
avoid injury to yourself, such as scraping
your hands against the wheel. Make sure
turning the wheel wrench will not scratch or
damage the wheel rim.
iFor information on storing the spare wheel
back into the trunk, see “Storing the spare wheel
after use” (
page 402).
!The maximum distance in emergency
mode depends on the vehicle’s load. It is
30 miles (50 km) if the vehicle is partially
loaded and 18 miles (30 km) if the vehicle is
fully loaded.
The point at which the maximum driving distance
begins in emergency mode is when the warning
message appears in the multifunction display
indicating that there is a loss of tire inflation
pressure.
Do not exceed the maximum speed of
50 mph (80 km/h).