2008 MERCEDES-BENZ SL55AMG Battery

131 Controls in detail
Lighting
Lighting
For information on how to switch on the
headlamps and use the turn signals, see
“Switching on headlamps” (
page 57)
and “Turn signals” (
page 57).
Exterior lamp switch
Exterior lamp switch
iIf you drive in countries where vehicles drive
on the other side of the road than the country in
which the vehicle is registered, you must have
the headlamps modified for symmetrical low
beams. Relevant information can be obtained at
any authorized Mercedes-Benz Center.
1‚Standing lamps, left
(turn left two stops)
2ˆStanding lamps, right
(turn left one stop)
3MOff
Daytime running lamp mode
(
page 133)
4UAutomatic headlamp mode
Daytime running lamp mode
(
page 133)
5CParking lamps (also side marker
lamps, tail lamps, license plate
lamps, instrument panel lamps)
6BLow beam headlamps or high
beam headlamps.
7‡Front fog lamps
8†Rear fog lamp
iIf you hear a warning signal, you have forgot-
ten to switch off the low beam headlamps or the
parking lamps before opening the driver’s door.
In addition, the message
Lights Are Still
On
appears in the multifunction display.
Switch off the low beam headlamps or the park-
ing lamps.
If the message
Switch off lights or
remove key.
appears in the multifunction
display, remove the SmartKey from the starter
switch or switch off the automatic headlamp
mode.
!Failure to switch off the exterior lamps when
leaving the vehicle may result in a discharged
battery.

187 Controls in detail
Good visibility
Glare through a door window
Swing respective sun visor down.
Disengage the sun visor from
mounting1.
Pivot the sun visor to the side.
Vanity mirror
Swing respective sun visor down.
Flip up vanity mirror cover2 to access
the vanity mirror.
Vanity mirror lamp 3 comes on.
After using the vanity mirror, flip down
vanity mirror cover 2.
Swing the sun visor up.
Rear window defroster
The rear window defroster uses a large
amount of power. To keep the battery
drain to a minimum, switch off the defrost-
er as soon as the rear window is clear. The
defroster is automatically deactivated af-
ter approximately 6 to 17 minutes of oper-
ation depending on the outside
temperature.
Switch on the ignition (page 40).
Activating
Press button F on the automatic cli-
mate control panel (
page 190).
The indicator lamp on the button
comes on.Deactivating
Press button F (page 190) once
more.
The indicator lamp on the button goes
out.
iWhen the sun visor is disengaged from
mounting1, vanity mirror lamp3 switches
off.
!To avoid damage to vanity mirror cover 2,
make sure it is closed before pivoting the sun
visor to the side.
Warning!G
Any accumulation of snow and ice should be
removed from the rear window before driv-
ing. Visibility could otherwise be impaired,
endangering you and others.
!The rear window defroster cannot be
switched on when the retractable hardtop is
open. The indicator lamp will start flashing if the
hardtop is open.

Close the retractable hardtop.
The rear window defroster can then be switched
on.
!If the rear window defroster switches off too
soon and the indicator lamp starts flashing, too
many electrical consumers are operating simul-
taneously and there is insufficient voltage in the
battery. The system responds automatically by
switching the rear window defroster off.
As soon as the battery has sufficient voltage, the
rear window defroster automatically switches
back on automatically.

200 Controls in detail
Automatic climate control
Deactivating
Press button T (page 190).
The indicator lamp on the button goes
out.
The residual heat is automatically turned
off:

when the ignition is switched on

after about 30 minutes

if the battery voltage drops
Ventilated glove box
The glove box has its own air vents that
allow for cooling ventilation when the auto-
matic climate control system is activated.
Glove box
1Thumbwheel
2Air ventOpening the air vent
Make sure the air vent in the glove box
is unobstructed.
Turn thumbwheel1 upwards.
Closing the air vent
Turn thumbwheel1 downwards.
iYou should keep air vent 2 closed when
outside temperatures are low.

203 Controls in detail
Power windows
Fully closing the door windows
(Express-close)
Pull switch1 or2 past the resis-
tance point and release.
The corresponding door window closes
completely.
If the upward movement of the door win-
dow is blocked during the closing proce-
dure, the door window will stop and open
slightly.
Stopping windows
Press or pull the respective switch
again.Closing the windows with
KEYLESS-GO*
Press and hold lock button on an out-
side door handle (
page 66) until the
windows are closed.
Synchronizing power windows
The power windows must be synchronized
each time

after the battery has been dis-
connected

if the power windows cannot be fully
opened (Express-open) or closed
(Express-close)
Synchronizing the power windows
Switch on the ignition (page 40).
Pull the power window switches until
the side windows are closed.
Hold the switches for approximately
1 second.
The power windows are synchronized.
Warning!G
Driver’s door only:
If within 5 seconds the switch is again
pulled past the resistance point and
released, the automatic reversal will not
operate.
Warning!G
When closing the windows make sure that
there is no danger of anyone being harmed
by the closing procedure.
The windows will not automatically re-open
if blocked during convenience closing.
If potential danger exists, proceed as
follows:

Release the lock button.

Pull on the door handle and hold firmly.
The side windows open for as long as
the door handle is held but the door not
opened.

208 Controls in detail
Retractable hardtop
Unlocked status noticed when stopped
Switch on the ignition (page 40).
To lock the retractable hardtop in its
fully closed position, press retractable
hardtop switch forward (
page 205).
or:
To lock the retractable hardtop in its
fully opened position, pull up on the re-
tractable hardtop switch (
page 205).Unlocked status noticed while drivingStop the vehicle in a safe location or as
soon as it is safe to do so.
Leave the ignition switched on.
To lock the retractable hardtop in its
fully closed position, press retractable
hardtop switch forward (
page 205).
or:
To lock the retractable hardtop in its
fully opened position, pull up on the re-
tractable hardtop switch (
page 205).Problems when operating the
retractable hardtop
Several conditions may cause the retract-
able hardtop to not open, close, or lock
properly:

The luggage cover in the trunk is not
closed.
Close the luggage cover in the
trunk.

The trunk lid is open.
Close the trunk lid.

The battery voltage is too low.
Start engine and let run while open-
ing/closing the retractable hard-
top.
Warning!G
Stop the vehicle in a safe location or as soon
as it is safe to do so and lock the hardtop be-
fore continuing to drive. You could other-
wise endanger yourself and others.

249 Controls in detail
Useful features
If applicable, remove the cover for the
external antenna connection from the
back of the mobile phone and store it in
a s a f e p l a c e . B e s u r e t o c o m p l y w i t h t h e
mobile phone’s operating instructions
as well.
Example illustration
1Insert the mobile phone
2Connector contact
3Mobile phone cradle
Slide the lower end of the mobile phone
into connector contact 2 on
cradle3.
Push the top of the mobile phone in di-
rection of arrow 1, until the lug on the
mobile phone release button engages.
The mobile phone is connected to the
network via the external antenna.
The mobile phone is linked to the
hands-free device and the multifunc-
tion steering wheel.
The battery is charged depending on its
charge status and the position of the
SmartKey in the starter switch. The
charge procedure will be indicated in
the mobile phone’s display.
You can place or receive phone calls. You
can control other functions of the mobile
phone via the control system
(
page 169), the Voice Control System*
(see separate operating instructions), or
COMAND (see separate operating
instructions). Removing mobile phone from mobile
phone cradle
Example illustration
1Release catch for mobile phone
2Mobile phone cradle
iWhen you take the SmartKey out of the
starter switch, the mobile phone remains
switched on for approximately 10 minutes. If you
place or receive a call during this time, the
mobile phone switches off 10 minutes after the
call has been completed.
iWhen using a flip-style mobile phone, open
flip top before removing from the cradle while a
call is connected. Otherwise, the call will be dis-
connected.


251 Controls in detail
Useful features
The Tele Aid system
(Tele
matic Alarm Identification on De-
mand)
The Tele Aid system consists of three
types of response:

Automatic and manual emergency

Roadside Assistance

Information
The Tele Aid system is operational provid-
ing that the vehicle’s battery is charged,
properly connected, not damaged and cel-
lular and GPS coverage is available.
The speaker volume of a Tele Aid call can
be adjusted when using the volume control
on the multifunction steering wheel. To
raise, press buttonæ and to lower,
press buttonç or use the volume knob
on your COMAND headunit.
To activate, press the SOS button, the
Roadside Assistance button• or
the Information button¡, depend-
ing on the type of response required.Shortly after the completion of your Tele
Aid acquaintance call, you will receive a
user ID and password. By visiting
www.mbusa.com and selecting “Tele Aid”
(USA only), you will have access to account
information, remote door unlock, and
more.
System self-check
Initially, after switching on the ignition,
malfunctions are detected and indicated
(the indicator lamps in the SOS button, the
Roadside Assistance button• and the Information button¡ stay on longer
than 10 seconds or do not come on). The
message
Tele Aid Inoperative appears
for approximately 10 seconds in the multi-
function display.
iThe SOS button is located above the interior
rear view mirror (
page 253).
The Roadside Assistance button• and the
Information button¡ are located below the
center armrest cover (
page 239).
!The Tele Aid system utilizes the cellular
network for communication and the GPS (Global
Positioning System) satellites for vehicle loca-
tion. If either of these signals are unavailable, the
Tele Aid system may not function and if this
occurs, assistance must be summoned by other
means.
Warning!G
If the indicator lamps in the SOS button, in
the Roadside Assistance button, and/or in
the Information button do not come on dur-
ing the system self-check, or if any of these
indicators remain illuminated continuously
in red and/or the message
Tele Aid
Inoperative
is displayed in the multifunc-
tion display after the system self-check,
a malfunction in the system has been
detected.
If a malfunction is indicated as outlined
above, the system may not operate as ex-
pected. Have the system checked at the
nearest Mercedes-Benz Center as soon as
possible.

262 Controls in detail
Useful features
Operation of integrated remote control
Switch on the ignition (page 40).
Select and press the appropriate inte-
grated signal transmitter button (2,
3 or4) to activate the remote con-
trolled device.
The integrated remote control trans-
mitter continues to send the signal as
long as the button is pressed – up to
20 seconds.
Erasing the integrated remote control
memory
Switch on the ignition (page 40).
Simultaneously press and hold outer
signal transmitter buttons2 and 4,
for approximately 20 seconds, until the
indicator lamp1 flashes rapidly. Do
not hold for longer than 30 seconds.
The codes of all three channels are
erased.Programming tips
If you are having difficulty programming
the integrated remote control, here are
some helpful tips:

Check the frequency of hand-held re-
mote control5 (typically located on
the reverse side of the remote). The in-
tegrated remote control is compatible
with radio-frequency devices operating
between 280-390 MHz.

Put a new battery in hand-held remote
control5. This will increase the likeli-
hood of the hand-held remote control
sending a faster and more accurate sig-
nal to the integrated remote control.

While performing step 3, hold
hand-held remote control5 at
different lengths and angles from the
signal transmitter button (2, 3 or4)
you are programming. Attempt varying
angles at the distance of
2 to 5 in (5 to 12 cm) away or the
same angle at varying distances.

If another hand-held remote control is
available for the same device, try the
programming steps again using that
other hand-held remote control. Make
sure new batteries are in the hand-held
remote control before beginning the
procedure.

Straighten the antenna wire from the
garage door opener assembly. This
may help improve transmitting and/or
receiving signals.
iIf you sell your vehicle, erase the codes of all
three channels.
iCertain types of garage door openers are in-
compatible with the integrated remote control. If
you should experience further difficulties with
programming the integrated remote control,
contact an authorized Mercedes-Benz Center, or
call Mercedes-Benz Customer Assistance
Center (in the USA only) at
1-800-FOR-MERCedes, or Customer Service (in
Canada) at 1-800-387-0100.